1、Bc _ AN102101 THRU AN102200 REV 3 53 W 9479915 O000232 5 = PROFILE K k.000 PART NO. - .o60 (a) 102106 AN102107 AN102108 .i25 AN102109 .i88 AN102110 ,250 AN102111 .3U. AN102112 AN102112 -500 AN102115 10211 .562 102116 .625 AN102117 .688 AN102118 .750 AN102119 .812 AN102120 .a75 AN102121 .938 AN102122
2、 1.000 AN10212 1.062 AN102122 PED. SUP CLASS. 5306 -4 O L 1 .a75 2.000 2,125 2,250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3,250 3.375 3.500 3.625 3.750 2: 4.125 4.250 4.375 AHs2800. RAISED OR DEPRESSED MATERIAL IDENTIFICATION PER .O10 MAX CHAMFER APPROX- .O47 x 45 K TO PULL THD zz a .O16 OR CHMER
3、 102134 AN102135 AN102136 mio2137 102138 AN102139 J 5.625 6.ooo 120f AIR FORCE-NAVY AERONAUTICAL STANDARD P.A. Af-II CUIT. NAVY - A9 BOLT - HEX HEAD, DRILLED SHANK, .3125-24 ARMY-AV I - AN 102101 ANI 02 200 THRU L 625 .688 -750 .e12 .a75 .938 L. 06.2 1.000 1.125 1.188 1.250 1.312 1.375 1.438 i .500
4、1.562 1.625 1.688 1.750 DRILL NO. 51 CSINK BOTH SIDES 60 To .lo0 DIA SECTION THRU THRE - A - .515 2x0 .TO2 .?65 .828 .ago .952 1 .O15 1 .W8 1.140 1.202 1.265 1.328 1. go 1.252 1.515 1.578 1.640 - CHAMFER 30 TO .500 DIA (OPPOSITE SIDE OPTIONAL) - A 1.765 1.890 2.915 2.140 2.390 2.515 2.640 2.765 2.89
5、0 3.015 3.140 3.265 3.515 3.640 3.765 3.890 4.015 2.265 3.390 . 3125-24UNF-3AJ SPEC n1s-7742 THIS SURFACE MUST BE SQUAW WITH SHANK WITHIN ,003 FIR. K +.o00 - * 060 1.188 1.312 1.438 1.562 i .688 1.812 1.938 2.062 2.188 ;:i; 2.562 2.688 2.812 2.938 3.062 3.188 3.312 3.438 3.562 3 .a8 AN102128 4 .e75
6、AN102129 / 5.000 AN102130 5.125 AN102131 11 5.250 AN102132 5.375 AN102133 5.500 A 4.390 4.515 4.640 4.765 4.890 5.015 5.140 5.265 5.390 5.515 5.640 5 -890 - 5.765 II: 1- 2 HOLES ON AXIS OP THD WITHIN .005. ANOULAR LOCATION OP THIS OROUP AS A UNIT WAY VARY PREBLY K + , O00 3 .812 4.062 4.188 -.o60 3.
7、938 - :i; 4,562 4.688 4.812 4.938 5.062 5.188 5.312 PART NO, 102146 AN102147 AN102148 . AN102149 AN102150 AN102151 AN102152 AN10215 AN102152 AN102155 AN102156 AN 1021 57 102158 (a) THREAD TO HEAD. MAXIMUM ?wo IMPERFECT THREADS. SHANK SHALL BE STRAIOHT WITHIN .O03 FIR.PER INCH OP BOLT LENOTH. THE CON
8、CENTRICITY OP THREAD PD IN RELATION TO THE SHANK SHALL BE YITHIN ,006 FIR. THE CONCENTRICITY OP THE SHANK IN RELATION M THE WASHER FACE DIAHETER AND HEXION SHALL BE WITHIN ,015 FIR. MATERIAL: SlEEL AMS6322 HARDHESS: ROCKWELL C26-32 FINISH: CADIIZRI PLATE AM2400 ._ SIIRPACE ROUOHNESS: ASlW IIANWACTURINO SPECIFICATION: AMs7452 BREAK SHARP EDQES .003-.O15 UNLESS 0THERWISE.SPECIFIED. DUENSION3 IN INCHES. M NOT USE UNASSIONED PART NUMBERS. UpSS OTHERWISE SPECIBIED: TOLERANCES; LIMAR DIWISIONS *.010. ANGULAR DIMENSIONS i2 . Licensed by Information Handling Services
