1、ANLOL1303 THRU ANLOL1200 REV 3 53 7777735 0000251 7 -t e . - 3-1749 THIS SURFACE MUST BE SQUnRE WITH SHANK WITHIN -003 FIR. L .750 .87.5 .938 1.ooO 1.062 1.125 1.188 .812 1.250 1.312 1.375 1.438 1.500 K .o00 . O60 - la1 (II (il .!$I .250 .312 .375 SECTION THRU THREAD PROFILE PART NO L 1.562 AN104106
2、 1.625 AN104107 1.688 AN104108 1.750 AN104109 1.812 AN104111 1.938 AN104112 . 2,000 AN104113 2.062 AN104114 2.125 AN104115 2.250 104116 2.375 ANlOh117 2.500 104110 1.875 niriii8 2.625 - K .k .o00 .438 .500 .625 .688 .750 .812 .875 .938 1.000 1.125 1.250 1.375 1.500 - .562 - CHAMFER 30 TO ,625 DIA (O
3、PPOSITE SIDE OPTIONAL) PART NO. L AN104119 2.750 AN104121 3.000 AN104122 3.125 AN104123 3.250 AN104124 3.375 AN104125 3.500 AN104126 3.625 AN104127 3.750 AN104128 3.875 AN104129 4 .O00 AN104130 4.125 AN104131 4.250 AN104132 4.375 104120 2.875 - K t.000 -.o60 1.625 - 1.750 1.875 2.000 2 .I25 2.250 2.
4、375 2.500 2.750 2,875 3.000 3.125 3.250 2.625 - PART NO. L AN104133 4.500 104134 4.625 AN104135 4.750 104136 4.875 AN104137 5 .O00 lurio4138 5.125 AN1041 9 5.250 AN104120 5.375 AN104141 5.500 104142 5.625 AN104143 -5.750 AN104144 5.875 AN104145 6.000 AN104146 K +.O00 -.o60 3.375 3.500 3.625 3.750 .8
5、75 4.125 4.250 4.375 4.500 4 625 4.750 4.875 - 2.000 PART NO. AN104147 AN104148 AN104149 AN104150 AN104151 AN104152 AN104153 AN104154 AN104155 104156 AN104157 104158 AN104159 (a) THREAD TO HEAD. MAXIMUM WO IMPERFECT TKREADS. NOTE: 1) I; THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE D
6、IMETER AND HEXAGON SHANK SHALL BE STRAIGHT WITHIN .O025 FIR.PER INCH OF BOLT LENGTH. THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. SHALL BE WITHIN .O19 FIR. MATERIAL: STEEL AM6322 HARDNESS: ROCKYELL C26-32 FINISH: CADMIW P-LATE M2400 SURPACE ROUGHNESS : AS 107 MAN
7、UFACTURING SPECIFICATION: AX37452 INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AMs2640 BREAK SHARP EWES .003-.O15 UNLESS OTHERWISE SPECIFIED. DMENSIOEIS IN INCHES- UNLESS OTHERWISE SPECIFIEn: TOLERANCES; LINEAR DIMENSIONS I.010, ANQULAR 3 :sf4 THRU 2 gI:! ,A. A-11 AN104
8、200 CUIT. NAVY-AS BOLT - DRILLED HEX HEAD, 6 HOLES, .4375;20 -1. I ARMY - AV Project No.5306-1025 DIHENSIONS f2. DO NOTUSE UNASSIQNED PART NUMBERS. INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 NO SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS CWITTEE OF THE SAE. I AIR FORCE-NAVY AERONAUTICAL STANDARD I AN104101 fl THIS DOCUMENT CONTAINS 1 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
