1、AN104701 THRU ANLOLiBOO REV 3 53 W 777771!i 0000257 T = MATERIAL IENTIFICATIOH PER AMS 2800. RAISED OR DEPRESSED .O10 MAX .156 L .500 .562 .625 .688 -750 .812 .938 1.000 1.062 1.125 1. i88 1.250 -875 K +.o00 - .o60 13 13 .125 . i88 .250 .312 .375 .438 .500 .562 .625 PfST NO. AN104706 AN104707 AN1047
2、08 AN104709 AN104710 AN104711 AN104712 AN104713 ANl.64714 AN104715 AN104716 AN104717 AN104718 K TO FULG T - SECTION THRU THREAD TFJS SURFACE MUST BE SQUARE WITH READING SHANK WITHIN .o03 PULL INDICATOR i CHAMFER 30. TO .438DIA (OPPOSITE SIDE OPTIONAL) L 1,312 1.375 1.438 1.500 1.562 1.625 1.688 1 *
3、750 1 - 875 2.000 2.125 2.250 2.375 2.500 - K +.o00 - .O60 .688 .812 a750 - 875 * 938 1.000 1.062 1.80 1.375 1.500 1.625 1.875 1.125 1.750 PART NO. AN104719 AN104720 AN104721 AN104722 A I il O 4 7 2 3 AN104724 AN104725 AN104726 AN104727 AN104728 AN104729 AN 1 O 4 7 3 O AN104731 AN104732 L - 2.625 2.
4、750 2 *875 .O0 3.125 3 * 250 3.375 3.500 3.625 4 .ao0 3.750 3 * 875 4.125 4.250 K +.o00 - .O60 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 PART NO. AN104733 AN104734 AN104735 AN104736 AN10473 AN10473g AN104739 AN104740 AN104741 AN104742 AN104743 AN104744 An047
5、45 Am04746. L - 4.375 4.500 4.625 4.750 4.875 5.000 5- 125 5 250 5.375 5.500 5.625 6.000 5.750 5 * 875 - - K +.o00 - .o60 3.750 3.875 4.125 4.375 4.000 4.250 4.500 4.625 4 750 4.875 5.000 5.125 5.250 5.375 PART NO AN 1 O 4 7 % AN10474i AN 1 O 4 7 4 : AN10475C AN104751 AN10475: AN10475: AN104754 AN10
6、475: AN104756 AN104757 AN10475E AN10475C AN104762 (a) THREAD TO HEAD. MAXIMUM TWO IHPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O03 FIR. PER INCH OF BOLT LENGTH, (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN
7、 RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL BE ULTHIN ,013 FIR. HATBRIAL: CORROSION RESISTANT STEEL - SEE MANUFACTURING SPECIFICAT104 SWPACE ROUGHNESS: 107 MANUFACTURING SPECIFICATION: AMs 7472 iNSPECIIOH: ALL PARIS SMALL UADERCO ILUDRESGCII IFISPECIIOA Il4 ACCORDANCS YITA AUS2645 BREAK
8、SHARP EDGES .003-.O15 UNLESS OTHERWISE SPECIFIED DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIMENSIONS 2.010, ANGULAR DIMENSIONS 2. DO NOT USE UNASSIGNED PART NUMBERS. INACTIVE FOR NEW DESIGN AFTER 27DEC 1966 ND SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVEL
9、Y BY THE ENGINE AND PROPELLER UTILITY PARTS COMHITTEE OF THE SAE. AIR FORCE-NAVY AERONAUTICAL STANDARD AN I0478 I AN I ?%e00 P.A. Other Cust USAF - 11 Navy - AS Army - AV BOLT - CRES HEX HEAD .250-28 u L o r E - c r v .d L e P h r h L i! 0 CI e r c E - U n o u a c e 0: C LI n - / “qolect No. 5306-1031 . - - THIS DOCUMENT CONTAINS -! -. - PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
