1、AN107801 THRU AN107700 REV 3 53 = 7777735 0000288 T K TO FULL TI CHAMFER .o47 x 45 .I60 TO POINT .O16 OR CHAHFE APPROX &i- SECTION THRU THREAD PROFILE .500-20 UNF-3A SPEC HTL-S-Z THIS SURFACE MUST BE SQUARE WITH SHANK KITHIN .O03 FULL INDICATOR DRILL NO. 50 (.070) CSINK 90 TO _ L - . O00 .O62 .125 .
2、I88 .250 .3L2 .375 .438 .500 ,562 .625 .688 .750 .IO0 DIA 6 HOLES SPACED AS SHOWN WITHIN .O20 OF TRUE POSLTION PART NO. AH107806 AN107807 AN107808 AN107809 AMI 0781 O AN I O78 I I AN 1078 I2 AN107813 ANI07814 ANI O 78 15 AN 1078 I6 ANI0781 7 AN107818 L 1.812 1.875 I .Y38 2.000 2.062 2.125 2.188 2.25
3、0 2.375 2.500 2.625 2.750 2.875 3.000 LCHAMFER 30 TO .750 DIA (OPPOSITE SIDE OPTIONAL) K f.000 -.O60 .562 .625 .688 .750 .a12 .875 .938 I .o00 1.125 1.250 I. 375 1.500 I .625 1.750 PART NO AN1078 19 AN I O 7820 AN IO78 2 I AN IO7822 AN107823 AN 107824 AN107825 AN LO7826 AN107827 AN107828 AN 107829 A
4、N107830 AN107831 AN107832 _ L - 3,125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 K t. O00 -. O60 I .75 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3,000 3.125 3.250 3.375 3.500 PART NO. AN107833 AN107834 AN107835 AN 107836 AN I07837 AN 107838 AN 107839 AN107840
5、 AN107841 AN107842 AN107843 AN 107844 AN107845 AN107846 +.o00 - . O60 4.875 3.625 5.000 3.750 ! 5.125 3.875 5.250 4.000 5.375 4.125 5.500 4.250 5.625 4.375 5.750 4-500 5.875 4.625 6.000 4.750 I (a) THREAD TO HEAD. UAXIUUU TWO IUPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT YITHIN .O02 FIR. PER
6、INCH OF BOLT LENGTH. (2) THE CONCELTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE YITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK I RELATIOI TO THE YASHER FACE DIAUETER AND HEXAGON SHALL BE UITHIN ,023 FIR. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. UATERIAL: CORROSIO
7、N RESISTANT STEEL - SEE UANUPACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 UANUFACTURING SPECIFICATION: AUS 7472 PART NO. AN107847 AN107848 AN107849 AN107850 AN107851 AN107852 AN i 0785 3 AN 107854 AN 107 855 iN 1 O 78 56 ) INSPECTION: ALL PARTS SHALL UNDERGO FLUORESCENT PENETBANT INSPECTION IN AC
8、CORDANCE YITH 2645. BREAK SHARP EDGES .O03 - .O15 UNLESS OTHERYISE SPECIFIED. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED:. TOLERANCES: LINEAR DIUENSIONS f.O1O. ANGULAR DIMENSIONS i2*. DO NOT USE UNASSIGNED PART NUUBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UT
9、ILITY PARTS GOMUITTEE OF THE CAE. P.A. AIR FORCE-NAW AERONAUTICAL STANDARD AN 10780 I Other Cust USAI - 11 Navy - AS Army - AV BOLT - CRES DRILLED HEX HEAD. 6 HOLES, -500-20 AN i8“79Op VA OD.-O*.L tmmadw *. - Project No. 5306-1062 THIS DOCUMENT CONTAINS -./ - - PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
