1、AN30770L THRU ANLO8000 REV 3 53 W 7777735 0000289 3 W FED. SUP CLAS. 5306 MATERIAL IDENTIFICATION PER ANS 2800. RAZSED OR DEPRESSED .O10 MAX CHAMFER .O62 x 45- DRILL .I88 TO 279 DEPTH SHOWN .175 TO POINT .O16 OR CHAMFE APPROX SECTION &L THRU THRE PROFILE .5625-48 UNF-SA SPEC MIL-S-7742 THIS SURFACE
2、MUST BE SQUARE WITH SHANK WITHIN .O03 FULL INDICATOR READING CSINK 90 TO .lo0 DIA OLES SPACED AS SHOWN WITHIN .O20 OF TRUE POSITION CHAUFER 30. TO .75 DIA -(OPPOSITE SIDE OPTIONAL) PART NO, AN107906 .188 AN 1 O7 907 AN107908 AN107909 .375 AN107910 AN107915 AN107916 .812 .438 AN107917 .875 I .500 I A
3、N107918 L K PART NO +. O00 - .o60 1 936 7.000 2.062 2.188 2.125 S250 2.312 2.500 7.375 2.625 2.750 2.875 3.000 3.125 ANl07Q19 2% AN107920 .688 I 107pi .750 AN107922 .812 AN107923 .875 AN107924 .938 AN107925 1.000 AN107926 1.125 AN107927 1.250 AN107928 1.375 AN107929 1.500 AN107930 1.625 107931 1.750
4、 AN107932 L - 3.250 3.375 3.500 3.625 3 - 750 3.875 4.000 4.125 4.250 4.500 4.375 4.&5 K +.ooc - .06c 1 875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2 * 875 3.000 3.125 3.250 3375 3.500 - T AN107933 5.000 AN107934 5.125 AN107935 5.250 AN107936 5.375 AN107937 5.500 AN107938 5.625 AN107939 5.750 AN10
5、7940 5.875 AN107941 6.000 iiN107942 AN10794 AN107945 AN107 94 6 f.000 (a) THREAD TO HEAD. UAXIUUU TWO IMPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRI
6、CITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXACON SHALL BE WITHIN .O26 FIR. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. KATERIAL: CORROSION RESISTANT STEEL - SEE MANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 MANUFACTURING SPECIFICATION: AMs 7472 INSPECTI
7、ON: BREAK SHARP EDGES .O03 - .O15 UNLESS OTHERWISE SPECIFIBD. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES: LINEAR DIMENSIONS t.010, ANGULAR ALL PARTS SHALL UNDERGO FLUORESCENT iENETRANT INSPECTION IN ACCORDANCE WITH AMS2645. DIUENSIDNS i2. DO NOT USE UNASSICNED PART NUMBERS. TUIS ST
8、ANDARD WAS DEVELOPED COOPERATIVELY WITH THk ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE, AN I 0790 I AN I 8Rh0 P.A. AIR FORCE-NAVY AERONAUTICAL STANDARD Ocher Cust USAP - 11 Navy - AS BOLT - CRES DRILLED HEX HEAD, 6 HOLES, .5625 - 18 Army - AV I I - Project No. 5306- -* -III-o.mcL ,-I,“, - THIS DOCUMENT CONTAINS - -I- - PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
