1、AMSC N/A FSC 4030 INCH-POUND AN116 Rev 3 9 December 2013 SUPERSEDING AN116 Rev 2 20 November 1956 DETAIL SPECIFICATION SHEET SHACKLE, ANCHOR, FORGER CARBON STEEL SCREW PIN This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquir
2、ing the product described herein shall consist of this specification sheet and RR-C-271. FIGURE 1 Shackle, anchor, forger carbon steel screw pin. Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land
3、and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432183990, or email fluidflow.dla.mil. Since contact information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil/. Inactive for new design after 16 June 1997, For n
4、ew design, use RR-C-271. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AN116 Rev 3 2 Table I. Dimensions for shackle, anchor, forger carbon steel screw pin. 1/2/3/4/5/6/7/8/9/ AN Part or Identifying Number (PIN) Breaking strength min. lb. (Ref)(kg)
5、 B Bow width (mm) D Min dia. (mm) E Inside dia. unthreaded eye (mm) AN116-3 2,600 (970) .625 (15.875) .062 (1.6) .188 (4.78) .281 (7.14) .016(.41) AN116-4 3,550 (1,325) .750 (19.05) .250 (6.35) .375(9.53) .031(.79) AN116-5 5,300 (1978) .875 (22.23) .312 (7.92) .438(11.13) AN116-6 7,950 (2967) 1.031
6、26.19) .375 (9.53) .500 (12.7) AN116-7 10,850 (4,050) 1.188 (30.18) .438 (11.13) .562 (14.27) AN116-8 14,150 (5281) 1.312 (33.32) .500 (12.7) .688 (17.48) AN116-9 17,900 (6681) 1.500 (38.1) .125 (3.18) .562 (14.27) AN116-10 22,100 (8249) 1.688 (42.88) .625 (15.88) .812 (20.62) AN116-12 31,800 (11,8
7、69) 1.938 (49.23) .750 (19.05) .938 (23.83) AN116-14 43,250 (16,143) 2.250 (57.15) .188 (4.78) .875 (22.23) 1.062 (26.97) AN116-16 56,550 (21,107) 2.625 (66.68) 1.000 (25.4) 1.188 (30.18) AN116-18 66,800 (24,933) 2.875 (73.03) 1.125 (28.58) 1.312 (33.32) AN116-20 82,500 (30,792) 3.188 (80.98) .250 (
8、6.35) 1.250 (31.75) 1.438 (36.53) AN116-22 99,800 (37,250) 3.562 (90.47) 1.375 (34.93) 1.562 (39.67) + .062/- .031 (1.6)/(.79) AN116-24 118,700 (44,304) 3.812 (96.82) 1.500 (38.1) 1.688 (42.88) AN116-26 139,500 (52,067) 4.438 (112.73) 1.625 (41.28) 1.812 (46.03) AN116-28 161,600 (60,316) 4.875 (123.
9、83) 1.750 (44.45) 2.094 (53.19) .062 (1.6) AN116-32 211,100 (78,791) 5.562 (141.27) 2.000 (50.8) 2.344 (59.54) See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AN116 Rev 3 3 Table I. Dimensions for shackle, anchor, forger ca
10、rbon steel screw PIN continued. 1/2/3/4/5/6/7/8/9/ AN Part or Identifying Number (PIN) L Inside length (mm) P Pin dia. (mm) AN116-3 .875(22.22) .062(1.6) .250(6.35) + .016(.41) - .000(0) AN116-4 1.125(28.58) .312(7.92) + .031(.79) - .000(0) AN116-5 1.250(31.75) .375(9.53) AN116-6 1.438(36.53) .438(1
11、1.13) AN116-7 1.688(42.88) .500(12.7) AN116-8 1.938(49.23) .625 (15.88) AN116-9 2.125(53.98) .0125(.318) AN116-10 2.500(63.5) .250(.635) .750(19.05) AN116-12 3.000(76.2) .875(22.23) AN116-14 3.250(82.55) 1.000(25.4) AN116-16 3.750(95.25) 1.125(28.58) AN116-18 4.250(107.95) 1.250(31.75) AN116-20 4.50
12、0(114.3) 1.375(34.93) AN116-22 5.250(133.35) 1.500(38.1) AN116-24 5.750(146.05) 1.625(41.28) AN116-26 6.250(158.75) 1.750(44.45) AN116-28 7.000(177.8) 2.000(50.8) AN116-32 7.750(196.85) 2.250(57.15) See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
13、ut license from IHS-,-,-AN116 Rev 3 4 Table I. Dimensions for shackle, anchor, forger carbon steel screw PIN. continued. 1/2/3/4/5/6/7/8/9/ AN Part or Identifying Number (PIN) R Outside dia. eye (mm) Thread T MIL-S-7742 W Width between eyes, (mm) WT, LB Approx. (gm.) AN116-3 .594(15.09) .062 (1.6) 1
14、/4-20 UNC-2A UNC-2B .375(9.5) .031 (.079) .08(30) AN116-4 .719(18.26) 5/16-18 .469(12) .12(45) AN116-5 .875(22.23) 3/8-16 .531(13.5) .21(78) AN116-6 1.000(25.4) 7/16-14 .656(16.7) .32(119) AN116-7 1.125(28.58) 1/2-13 .719(18.3) .49(183) AN116-8 1.312(33.32) 5/8-11 .812(20.6) .062 (1.6) .73(272) AN11
15、6-9 1.438(36.53) .875(22.2) .92(343) AN116-10 1.625(41.28) 3/4-10 1.062(27) 1.51(564) AN116-12 1.875(47.63) 7/8-9 1.250(32.) 2.26(844) AN116-14 2.062(52.37) 1-8 1.438(37) 3.40(1269) AN116-16 2.438(61.93) 1-1/8-7 1.688(43) 4.95(1848) AN116-18 2.688(68.28) 1-1/4-7 1.812(46) 6.91(2579) AN116-20 3.000(7
16、6.2) 1-3/8-6 2.000(51) 8.99(3355) AN116-22 3.312(84.12) 1-1/2-6 2.250(57) .125 (3.2) 12.19(4550) AN116-24 3.562(90.47) 1-5/8 - 5-1/2 NS-2A NS-2B 2.375(60) 15.95(5953) AN116-26 3.812(96.82) 1-3/4 - 5 UNC-2A UNC-2B 2.625(67) 19.10(7129) AN116-28 4.062(103.17) 2-41/2 2.875(73) 27.50(10264) AN116-32 4.6
17、25(117.48) .125 (3.2) 2-1/4 - 4-1/2 3.250(83) 39.00(14556) See notes at end of table. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Break sharp edges .and remove all hanging burrs and slivers. 4. Unless otherwise noted tolerances shall be .005 inches (0
18、13 mm) and angles .5. 5. Machined surfaces shall be smooth to 125in Ra, hex surfaces may be 250in Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1. 6. Type: RR-C-271, type IVA, class 2, with the exception of the requirements of this specification.
19、 7. Maximum working load equal to 1/5 minimum breaking strength as specified in table I. 8. Material: Forged carbon steel, see procurement specification RR-C-271. 9. Finish: Zinc coating, see procurement specification, except if the hot-dip (galvanizing) process is used, the coating shall be applied
20、 in accordance with specification ASTM A153/A153M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AN116 Rev 3 5 Shackle, anchor, forger carbon steel screw pin: See figure 1. PIN: The PIN consists of the prefix letter “AN” the specification sheet num
21、ber, and a dash number for tube size, and shackle size, AN116-4. AN116 - 4 Size Document Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. No
22、thing in this document, however supersedes applicable laws and regulations unless a specific exemption has been obtained. Referenced documents shall be of this issues in effect on date of invitations for bid. Changes from previous issue. Marginal notations are not used in this revision to identify c
23、hanges with respect to the previous issue due to the extensiveness of the changes. Referenced documents. In addition to RR-C-271, this document references the following: ASME B46.1. ASTM A153/A153M MIL-S-7742 CONCLUDING MATERIAL MILITARY INTERESTS CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA
24、 FSS Army - AV Navy - MC Preparing activity: Air Force - 99 DLA - CC DLA - CC Review activities: Project 4030-2014-005 Army-MI Navy SA,YD Air Force 71 DLA GS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
