1、 REVISIONS LT DESCRIPTION DATE APPROVED A Added: International Resistive Company as a new vendor. Editorial changes throughout. 21 APR 89 David E. Moore B Dimensional changes to figure 2. Delete 3.3.6. Editorial changes throughout. 15 JAN 91 David E. Moore C Changed drawing title. Add B tol., D tol.
2、, and H characteristic. Editorial changes throughout. 31 MAR 94 Andrew R. Ernst D Changes in accordance with NOR 5905-R004-94. 29 AUG 94 David E. Moore E Revise to present DoD policy requirements, new P/Ns, correct vendor CAGE, dimension change (figure 2), change reference to MIL-PRF-914, and editor
3、ial corrections throughout. 24 OCT 00 Kendall A. Cottongim F Add new characteristics “R” (25 ppm) and “V” (50 ppm). Add new source of supply. 15 OCT 01 Kendall A. Cottongim G Changes in accordance with NOR 5905-R001-03. 18 DEC 02 Kendall A. Cottongim H Add pure tin, manufacturers eligibility, and pu
4、lse application paragraphs. Editorial changes throughout. 15 MAR 13 M. Radecki CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV H H H H H H H PAGES 1 2 3 4 5 6 7 PMIC N/A PRE
5、PARED BY Allan R. Knox DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH Original date of drawing 16 June 1987 CHECKED BY David W. Withrow TITLE RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, GULL WING, 16 PIN APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 87012 REV H PAGE 1 OF 7 AMSC N/A
6、 5905-2012-E35 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87012 REV H PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a resistor network, f
7、ixed, film, small outline, 16 pin, supplied to the requirements of MIL-PRF-914 except as noted herein. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 87012 - A A001 K F Drawing number Schematic Resistance Characteristic Tolerance (1.2.1) (1.2.1.1) (1.2.1.2) (3.3.1) 1.2.1 Schem
8、atics. The schematic of the resistor network is identified by a single letter in accordance with the drawings (see figure 1). The resistor element RREFis the reference resistor element used in determining the ratio accuracy (when applicable). 1.2.1.1 Resistance value designations. The resistance val
9、ue designations are in accordance with MIL-PRF-914. Resistance value designations for the schematic J as specified in table I. TABLE I. Standard resistance values. Resistance designator R1(ohms) R2(ohms) Resistance designator R1(ohms) R2(ohms) A001 A002 A003 A004 A005 A006 A007 A008 A009 A010 82 120
10、 130 160 180 180 220 220 330 330 130 200 210 260 240 390 270 330 390 470 A011 A012 A013 A014 A015 A016 A017 A018 A019 A020 330 1.5 k 3.0 k 180 270 560 560 620 110 220 680 3.3 k 6.2 k 270 270 560 1.2 k 2.7 k 220 110 1.2.1.2 Characteristic. The characteristics are in accordance with MIL-PRF-914, chara
11、cteristic R, characteristic V, characteristic H, characteristic K, and characteristic M. 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified her
12、ein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-914 - Resistor Networks, Fixed, Film, Surface Mount, Nonestablished Reliability, and Established Reliability, General Specification For. * (Copi
13、es of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELEC
14、TRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87012 REV H PAGE 3 * 2.2 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related, specification sheet
15、s), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-914 and as specifie
16、d herein. 3.2 Interface and physical dimension requirements. Resistors shall meet the interface and physical dimensions as specified in MIL-PRF-914 and herein (see figure 2). FIGURE 1. Schematics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFEN
17、SE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87012 REV H PAGE 4 Inches .0030 .005 .010 .0105 .015 mm 0.076 0.13 0.25 0.267 0.38 Inches .018 .024 .026 .035 .050 mm 0.46 0.61 0.66 0.89 1.27 Inches .053 .060 .104 .220 .236 mm 1.35 1.52 2.64 5.59 5.99 Inches .300 .440 mm
18、 7.62 11.18 NOTES: 1. Dimensions are given in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm) for three place decimals. 4. Pin 1 locator shall be a dot, stripe, notch, or numeral 1 adjacent to pin number 1, in the shade
19、d area. 5. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspect of the device are acceptable. FIGURE 2. Resistor network. Provided by IHSN
20、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87012 REV H PAGE 5 3.3 Electrical characteristics. 3.3.1 Resistance tolerance. Resistors are available in B (0.1 percent), D (0.5 perce
21、nt), F (1 percent), G (2 percent), and J (5 percent) tolerances. 3.3.2 Resistor power rating. The power rating for schematic B and schematic J shall be 0.08 watt at 70C. The power rating for schematic A shall be 0.16 watt at 70C. 3.3.3 Packaging power rating. The packaging power rating shall be 1.2
22、watt at 70C. 3.3.4 Temperature range. The operating temperature range shall be -55C to +125C. 3.3.5 Resistance temperature characteristic. The resistance temperature characteristic shall not exceed 25 ppm/C for characteristic R, 50 ppm/C for characteristic V, 50 ppm/C for characteristic H, 100 ppm/C
23、 for characteristic K, and 300 ppm/C for characteristic M. 3.3.6 Resistance. The resistance values shall be 10 ohms to 2.2 megohms. 3.3.7 Operating voltage. The maximum operating voltage shall be 50 V dc. * 3.4 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both intern
24、ally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.5). 3.5 Marking. Resistors shall be marked with the PIN assigned herein (see 1.2) and manufacturers identification code (CAGE
25、 or logo). Pin 1 indicator shall be located adjacent to pin 1. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the materials meet or exceed the operational and m
26、aintenance requirements, and promote economically advantageous life cycle costs. * 3.7 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-914 Qualified Products List for at least one part, or perform the group A and grou
27、p B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VAT. * 3.7.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply. 3.8 Workmanship. Resistors shall be
28、 processed in such a manner as to be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection in accordance with MIL-PRF-914 is not applicable to this document. 4.2 Conformance inspection. 4.
29、2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A (M level part) and group B inspections. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B t
30、ests (see 6.2c). 4.3 Schematic J tests. For the tests on schematic J, the dc resistance measurements, resistance temperature characteristics measurement, and short time overload power application shall be made between each terminal and the application common terminal without compensation for the shu
31、nt circuits. The pin to pin dc resistance measurement shall be used directly to determine the acceptability to section 3 requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO
32、. 14933 DWG NO. 87012 REV H PAGE 6 5. PACKAGING * 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel or in-house contractor personnel, these personnel need
33、 to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the military services system commands. Packaging data retrieval is
34、available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intende
35、d use. Resistor networks are intended to be used in surface mounting applications where space is a major concern. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or a
36、certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group B tests or provides a certification of compliance with group B requirements (see 4.2.2). d. Requirements for packaging and packing.
37、6.3 Soldering. Extreme care should be taken when soldering these resistors. Prolonged exposure to high temperatures can damage these devices. 6.4 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from spec
38、ified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 which specifies a preventive packaging procedure. * 6.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may
39、 exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the fo
40、rmation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). * 6.6 Pulse applications. Designers are CAUTIONED on using the ab
41、ove resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. * 6.7 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the user
42、s of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. Provided by IHSNot for ResaleNo r
43、eproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87012 REV H PAGE 7 * 6.8 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they become availabl
44、e. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DLA Land and Maritime drawing PIN 87012-* 1/ Vendors similar designation or type numb
45、er Vendor CAGE Vendors name and address Characteristic K and M, Schematics A, B, and J, Resistance values 10 ohms to 1.0 megohms, Resistance tolerance D, F, G, and J. 767-16 768-16 11236 CTS Corporation Berne Division 406 Parr Road Berne, IN 46711-9505 Characteristic K and M, Schematics A, B, and J,
46、 Resistance values 10 ohms to 2.2 megohms, Resistance tolerance F, G, and J. SOMC-160* 91637 Vishay Dale PO Box 609 1122 23rdSt. Columbus, NE 68602-0609 Characteristic R, H, K, and M, Schematics A; Resistance values 10 ohms to 150k ohms Schematics B; Resistance values 10 ohms to 75k ohms Resistance
47、tolerance B, D, F, G, and J. GM8*-0*-*Y 57027 International Resistive Company 4222 South Staples Street Corpus Christi, TX 78411-2796 Characteristic R, V, H, K, and M; Schematics A and B; Resistance values 100 ohms to 100kohms; Resistance tolerances B, D, F, G, and J. 103-331 (Schematic A) 103-332 (
48、Schematic B) 57489 Vishay Thin Film 2160 Liberty dr. Niagara Falls, NY 14304-3676 1/ Parts must be purchased to this DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
