1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update and validation of drawing. Editorial changes throughout. 20 JUL 00 K. Cottongim B Pure tin prohibition added. Removal of Tolerances (B and D) and Vendor. Editorial changes throughout. 5 year review 30 AUG 12 M. Radecki Prepared in accordance with ASM
2、E Y14.100 Source control drawing REV STATUS OF PAGES REV B B B B B B B PAGES 1 2 3 4 5 6 7 PMIC N/A Original date of drawing 9 October 1992 PREPARED BY Dennis L. Cross DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH CHECKED BY Andrew R. Ernst TITLE RESISTOR NETWORKS, FIXED, FILM, 10 PIN, SIP, EXTENDED
3、LEAD LENGTH APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 92013 REV B PAGE 1 OF 7 AMSC N/A 5905-E621CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DLA LAND AND MARTIME COLUMBUS OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
4、,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92013 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 10 pin, single in line package (SIP), resistor network with a 100 ppm/OC temperature coefficient. 1.2 Part or Identifying Number (P
5、IN). The complete PIN is as follows: 92013 - * * * Drawing number Schematic (3.3.4) Resistance value designations (3.3.1.2 and table I) Resistance tolerance (3.3.2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handb
6、ooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resis
7、tor Networks, Ceramic Capacitor and Fixed , Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document
8、 Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of t
9、his document takes precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as
10、specified herein. 3.2 Interface, and physical dimensions. The resistor shall meet the interface, and physical dimensions as specified in MIL-PRF-83401 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPL
11、Y CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92013 REV B PAGE 3 Inches mm Inches mm Inches mm Inches mm Inches mm .004 0.10 .012 0.30 .024 0.61 .050 1.27 .342 8.69 .005 0.13 .014 0.36 .025 0.63 .074 1.88 .983 24.97 .006 0.15 .015 0.38 .035 0.98 .089 2.26 .009 0.23 .019 0.48 .040 1.02 .1
12、00 2.54 .010 0.25 .020 0.51 .049 1.24 .190 4.83 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .005 (0.13 mm). 3. The picturization of the styles above is given as representative of the envelope of the item
13、. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable. 4. Terminal centerline to centerline measurements made at point of emergence of the lead from the body. 5. Measurement made at point of emergence
14、 of the lead from the body. 6. Pin 1 locator shall be a bevel, stripe, notch or a dot above pin number 1 in the shaded area. 7. If the standoffs are located on the body, a minimum of two standoffs are required as illustrated. As an option, additional standoffs may be located on the body of the resis
15、tor network. If leads with standoffs are used, standoffs on the body are not required FIGURE 1. Resistor Network, 10 pin, SIP Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DW
16、G NO. 92013 REV B PAGE 4 3.3 Electrical characteristic. 3.3.1. Resistance. The resistance range shall be from 10 ohms to 1 megohms. 3.3.1.1 Resistance values. The nominal resistance is identified by four digits; the first three digits represent significant figures and the last digit specifies the nu
17、mber of zeros to follow. When the value of resistance is less than 100 ohms, or when fractional values of an ohm are required, the letter “R” is substituted for one of the significant digits of the group representing significant figures. 3.3.1.2 Resistance value designations. The resistance value de
18、signations is in accordance with MIL-PRF-83401. The resistance value designations for the “H” schematic are specified in table I. TABLE I. Standard resistance values. Resistance designator R1(ohms) R2(ohms) Resistance designator R1(ohms) R2(ohms) A001 82 130 A011 330 680 A002 120 200 A012 1.5k 3.3k
19、A003 130 210 A013 3k 6.2k A004 160 260 A014 620 910 A005 180 240 A015 180 270 A006 180 390 A016 270 270 A007 220 270 A017 560 560 A008 220 330 A018 560 1.2k A009 330 390 A019 620 2.7k A010 330 470 3.3.2 Resistance tolerance. Resistor networks are available in the following tolerances: Tolerance code
20、 Tolerance (percent) F +1.0 G +2.0 J +5.0 3.3.3 Resistor power ratings. The power rating for schematics C, G, and H shall be as follows: Schematic Element power rating (watts) Network power rating (watts) C 0.2 1.8 G 0.2 1.0 H 0.11 1.8 3.3.3 Voltage rating. The maximum continuous working voltage for
21、 each resistor shall not exceed 50 V dc or ac rms. 3.3.4 Schematic. The schematic of the resistor network is identified by a single letter in accordance with figure 2. 3.4 Environmental characteristic. The environmental characteristic shall be in accordance with MIL-PRF-83401 characteristic K. Provi
22、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92013 REV B PAGE 5 FIGURE 2. Schematics. 3.5 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited b
23、oth internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.6 Marking. Marking shall be accordance with MIL-STD-1285, except the resistors shall be marked with the PIN a
24、ssigned herein (see 1.2), manufacturers identification code (CAGE or logo), and date and lot codes. 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material
25、meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.8 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-83401 Qualified Products List for at least o
26、ne part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime - VAT. 3.8.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supp
27、ly. 3.9 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO.
28、 14933 DWG NO. 92013 REV B PAGE 6 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspection of MIL
29、-PRF-83401. 4.2.2 Certification. The procuring activity may accept a certificate of compliance in lieu of Group B inspection. 4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-83401. 4.4 “H” schematic tests. For the tests on “H” schematic, the dc resistance mea
30、surements, resistance temperature characteristics measurement, and short time overload power application shall be made between each terminal and the application common terminal without compensation for the shunt circuits. The pin to pin dc resistance measurement shall be used directly to determine t
31、he acceptability to section 3 requirements. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contac
32、t the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments Services System Command. Packaging data re
33、trieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6
34、.1 Intended use. Resistors networks are intended to be used in thick or thin film circuits where microcircuity is intended, also, for use in surface mounting application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for de
35、livery: One copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing (see 5.1). d. Whether the manufacturer performs the group B tests or provides ce
36、rtificate of compliance with group B (see 4.2.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92013 REV B PAGE 7 6.3 Tin whisker growth. The use of alloys with tin
37、content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a
38、whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Pulse applicatio
39、ns. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. 6.5 Users of record. Coordination of this document for future revisions is coordinated only with
40、the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved on-line at resistordla.mil or in writing to: DLA Land and Maritime, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-8754 or DSN
41、 850-8754. 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained on on-line at resistordla.mil or contact DLA Land and Maritime, Attn: VAT, P.O. Box 3990, Columbus
42、, OH 43218-3990, or by telephone (614) 692-8754 or DSN 850-8754. DLA Land and Maritime drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendors name and address 92013-* MSP10C*-YYYY-SNNN or 10L 91637 Sales: Vishay Dale, Inc. Post Office Box 609 Columbus, NE 68601-0609 Plant: Elec
43、tronica Dale De Mexico S.A. De CV, C. Joule No. 1920, Parque Ind. Antonio J. Bermudez, C.P. 32470, CD. Juarez, Chihuahua, Mexico 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and test are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
