1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update references, technical date, contact information, distribution statement. 24 April 2008 Abdonasser Abdouni B Updated Vendor PINs. 30 July 2009 Abdonasser Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAG
2、ES REV B A A B PAGE 1 2 3 4 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 20 April 2001 CHECKED BY TITLE Lee Surowiec CONNECTOR, PLUG, ELECTRICAL, RF, SERIES N, FOR LOW SMOKE CABLES APPROVED BY Rob Heber SIZE CAGE CODE DWG. NO. 01004
3、 A 037Z3 REV B PAGE 1 OF 4 AMSC N/A 5935-E832-001 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTES: 1. Dimensions are in inches; metric equivalents are in parentheses. 2. Metric equivalents are given for reference purposes only. 3. All undimensi
4、oned pictorial configurations are for reference purposes only. 4. No safety wire holes are required. 5. Series N, pin contact interface, in accordance with MIL-STD-348. 6. Dimension is .812 across flats. FIGURE 1. General configuration. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CA
5、GE CODE DWG NO. A 037Z3 01004 REV A PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ENGINEERING DATA: This document covers the requirements for radio frequency connectors accommodating special low smoke coaxial cables. REQUIREMENTS: These conn
6、ectors shall conform to all the requirements of the latest issue of DSCC drawing 84148, figure 1 herein, and MIL-PRF-39012/1, and accommodate the cables listed in table I, with the following additions and exceptions. Electrical: Shall be in accordance with MIL-PRF-39012/1. Mechanical: Shall be in ac
7、cordance with MIL-PRF-39012/1 with the following exception: No safety wire holes are required. Environmental: Shall be in accordance with MIL-PRF-39012/1. TABLE I. Cable accommodation. Part or Identifying Number (PIN) 1/ 2/ Applicable cable 01004NBSA M17/220-00001 01004NBSB # M17/221-00001 01004NBSC
8、 & M17/222-00001 01004NBSD $ M17/223-00001 01004NBSE % M17/224-00001 01004NBSF M17/225-00001 1/ These connectors have captivated center contacts. 2/ These connectors are assembled using the MIL-C-22520/5 crimp tool and using the following crimp dies: M22520/5-05 # M22520/5-07 & M22520/5-29 $ M22520/
9、5-25 % M22520/5-27 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01004 REV A PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Approved sources of supply. Approved sources of supply are listed herein. Add
10、itional sources will be added as they become available. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to Defense Supply Center Columbus, ATTN: DSCC-VAI, P.O. Box 3990, Columbus, OH 43218-3990 or emailed to RFConnectordla.mil . DSCC drawing PI
11、N Vendor similar PIN 1/ Vendor CAGE number 01004NBSA (3190-1070) Superseded by 1103320A001-003 00795 01004NBSB (3190-1151) Superseded by 1103311A001-005 00795 01004NBSC (3190-1177) Superseded by 1103348A001-002 00795 01004NBSD (3190-1080) Superseded by 1103300A001-012 00795 01004NBSE (3190-1199) Sup
12、erseded by 1103318A001-001 00795 01004NBSF (3190-1088) Superseded by 1103319A001-007 00795 1/ Parts must be purchased to this DSCC PIN to assure all performance requirements and test are met. Vendor CAGE Vendor name number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01004 REV B PAGE 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
