1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update references, technical date, contact information, distribution statement. 24 April 2008 Abdonasser Abdouni B Updated Vendor PINs. 30 July 2009 Abdonasser Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAG
2、ES REV B A A B PAGE 1 2 3 4 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 20 April 2001 CHECKED BY TITLE Lee Surowiec CONNECTOR, PLUG, ELECTRICAL, RF, SERIES BNC, FOR LOW SMOKE CABLES APPROVED BY Rob Heber SIZE CAGE CODE DWG. NO. 010
3、08 A 037Z3 REV B PAGE 1 OF 4 AMSC N/A 5935-E832-005 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01008 REV A PAGE 2 NOTES: 1. Dimensions are in inches; metric e
4、quivalents are in parentheses. 2. Metric equivalents are given for reference purposes only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Series BNC, pin contact interface, in accordance with MIL-STD-348. FIGURE 1. General configuration. SEE NOTE 4 Provided by IHS
5、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01008 REV A PAGE 3 ENGINEERING DATA: This document covers the requirements for radio frequency connectors accommodating special lo
6、w smoke coaxial cables. REQUIREMENTS: These connectors shall conform to all the requirements of the latest issue of DSCC drawing 84148, figure 1 herein, and MIL-PRF 39012/16, and accommodate the cables listed in table I, with the following additions and exceptions. Electrical: Shall be in accordance
7、 with MIL-PRF-39012/16. Mechanical: Shall be in accordance with MIL-PRF-39012/16. Environmental: Shall be in accordance with MIL-PRF-39012/16. TABLE I. Cable accommodation. Part or Identifying Number (PIN) 1/ 2/ Applicable cable 01008BBSA M17/220-00001 01008BBSB # M17/221-00001 01008BBSC & M17/222-0
8、0001 01008BBSD $ M17/223-00001 01008BBSE % M17/224-00001 01008BBSF M17/225-00001 1/ These connectors have captivated center contacts. 2/ These connectors are assembled using the MIL-C-22520/5 crimp tool and using the following crimp dies: M22520/5-05 # M22520/5-07 & M22520/5-29 $ M22520/5-25 % M2252
9、0/5-27 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01008 REV B PAGE 4 Approved sources of supply. Approved sources of supply are listed herein. Additional sour
10、ces will be added as they become available. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to Defense Supply Center Columbus, ATTN: DSCC-VAI, P.O. Box 3990, Columbus, OH 43218-3990 or emailed to RFConnectordla.mil . DSCC drawing PIN Vendor sim
11、ilar PIN 1/ Vendor CAGE number 01008BBSA (3190-1069) Superseded by 1003320A001-000 00795 01008BBSB (3190-1148) Superseded by 1003311A001-001 01008BBSC (3190-1174) Superseded by 1003348A001-001 01008BBSD (3190-1078) Superseded by 1003300A001-000 01008BBSE (3190-1196) Superseded by 1003318A001-000 010
12、08BBSF (3190-857) Superseded by 1003319A001-000 1/ Parts must be purchased to this DSCC PIN to assure all performance requirements and test are met. Vendor CAGE Vendor name number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
