1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update references, technical date, contact information, distribution statement. 24 April 2008 Abdonasser Abdouni B Updated Vendors PINs. 30 July 2009 Abdonasser Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PA
2、GES REV B A A B PAGE 1 2 3 4 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 20 April 2001 REVISED BY TITLE Lee Surowiec CONNECTOR, PLUG, ELECTRICAL, RF, SERIES TNC, RIGHT ANGLE, FOR LOW SMOKE CABLES APPROVED BY Rob Heber SIZE CAGE COD
3、E DWG. NO. 01017 A 037Z3 REV B PAGE 1 OF 4 AMSC N/A 5935-E832-014 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01017 REV A PAGE 2 NOTES: 1. Dimensions are in in
4、ches. Metric equivalents are in parenthesis. 2. Metric equivalents are given for reference purposes only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. No safety wire holes are required. 5. Series TNC, pin contact interface, in accordance with MIL-STD-348. 6. Dime
5、nsion is .562 (14.27 mm) across flats. FIGURE 1. General configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01017 REV A PAGE 3 ENGINEERING DATA: This d
6、ocument covers the requirements for Radio Frequency connectors accommodating special low smoke coaxial cables. REQUIREMENTS: These connectors shall conform to all the requirements of the latest issue of DSCC drawing 84148, figure 1 herein, and MIL-PRF 39012/30, and accommodate the cables listed in t
7、able I, with the following additions and exceptions. Electrical: Shall be in accordance with MIL-PRF-39012/30. Mechanical: Shall be in accordance with MIL-PRF-39012/30 with the following exception: No safety wire holes are required. Environmental: Shall be in accordance with MIL-PRF-39012/30. TABLE
8、I. Cable accommodation. Part or Identifying Number (PIN) 1/ 2/ Applicable cable 01017TBSA M17/220-00001 01017TBSB # M17/221-00001 01017TBSC & M17/222-00001 01017TBSD $ M17/223-00001 01017TBSE % M17/224-00001 01017TBSF M17/225-00001 1/ These connectors have captivated center contacts. 2/ These connec
9、tors are assembled using the MIL-C-22520/5 crimp tool and using the following crimp dies: M22520/5-05 # M22520/5-07 & M22520/5-29 $ M22520/5-25 % M22520/5-27 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH
10、 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 01017 REV B PAGE 4 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted t
11、o Defense Supply Center Columbus, ATTN: DSCC-VAI, P.O. Box 3990, Columbus, OH 43218-3990 or emailed to RFConnectordla.mil . DSCC drawing PIN Vendor similar PIN 1/ Vendor CAGE number 01017TBSA (3190-848) Superseded by 1207320A001-000 00795 01017TBSB (3190-1158) Superseded by 1207311A001-001 00795 010
12、17TBSC (3190-1184) Superseded by 1207348A001-000 00795 01017TBSD (3190-1086) Superseded by 1207300A001-002 00795 01017TBSE (3190-1206) Superseded by 1207318A001-000 00795 01017TBSF (3190-858) Superseded by 1207319A001-001 00795 1/ Parts must be purchased to this DSCC PIN to assure all performance requirements and test are met. Vendor CAGE Vendor name number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
