1、REVISIONS LTR DESCRIPTION DATE APPROVED A Clarify VSWR and IL testing requirements as engineering info. 2 February 2010 Abdonasser M. Abdouni Prepared in accordance with ASME Y14.100 Source Control Drawing REV PAGE REV STATUS OF PAGES REV A A A A A PAGE 1 2 3 4 5 PMIC N/A PREPARED BY DEFENSE SUPPLY
2、CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 7 May 2001 CHECKED BY TITLE Lee Surowiec CONNECTOR, PLUG, ELECTRICAL, RF, SERIES N, 75 OHM, FOR LOW SMOKE CABLES APPROVED BY Robert Heber SIZE CAGE CODE DWG. NO. 01027 A 037Z3 REV A PAGE 1 OF 5 AMSC N/A 5935-E817-005 Provid
3、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01027 REV A PAGE 2 NOTES: 1. Dimensions are in inches; metric equivalents are in parentheses. 2. Metric equivalents are gi
4、ven for reference purposes only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. No safety wire holes are required. 5. Series N, pin contact interface, 75 in accordance with figure 2. 6. Dimension is .812 (20.62 mm) across flats. FIGURE 1. General configuration. Pro
5、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01027 REV A PAGE 3 NOTES: 1. Dimensions are in inches. Metric equivalents are in parenthesis. 2. Metric equivalents are
6、 given for information only. 3. Utilizes standard 50 body with 75 contact/air dielectric configuration. FIGURE 2. Interface, series N, pin contact, 75. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218
7、-3990 SIZECAGE CODE DWG NO. A 037Z3 01027 REV A PAGE 4 ENGINEERING DATA: This document covers the requirements for radio frequency connectors accommodating special low smoke coaxial cables. Frequency range: 0-2.5 GHz. VSWR: 1.30 :1, maximum. Insertion loss: .07 dB at 2 GHz. REQUIREMENTS: These conne
8、ctors shall conform to all the requirements of the latest issue of DSCC drawing 84148, figures 1 and 2 herein, and MIL-PRF-39012/1, and accommodate the cables listed in table I, with the following additions and exceptions. Electrical: Shall be in accordance with MIL-PRF-39012/1. Impedance: 75. Mecha
9、nical: Shall be in accordance with MIL-PRF-39012/1 with the following exception: No safety wire holes are required. Environmental: Shall be in accordance with MIL-PRF-39012/1. TABLE I. Cable accommodation. Part or Identifying Number (PIN) 1/ 2/ Applicable cable 01027NBSA M17/229-00001 1/ These conne
10、ctors have captivated center contacts. 2/ These connectors are assembled using the MIL-C-22520/5 crimp tool and using the following crimp dies: M22520/5-19 Closure A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLU
11、MBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01027 REV A PAGE 5 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed below have agreed to this drawing and a certificate of compliance has been subm
12、itted to DSCC-VAI. DSCC drawing PIN Vendor CAGE Number Vendor similar PIN 1/ 01027NBSA 00795 3190-1076 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and test are met. Vendor CAGE Vendor name number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
