1、REVISIONS LTR DESCRIPTION DATE APPROVED A Clarify VSWR and IL testing requirements as engineering info. 2 February 2010 Abdonasser M. Abdouni Prepared in accordance with ASME Y14.100 REV PAGE REV STATUS OF PAGES REV A A A A A PAGE 1 2 3 4 5 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMB
2、US, OHIO 43218-3990 Ron Gary Original date of drawing 7 May 2001 CHECKED BY TITLE Lee Surowiec CONNECTOR, PLUG, ELECTRICAL, RF, SERIES N, RIGHT ANGLE, 75 OHM,FOR LOW SMOKE CABLES APPROVED BY Robert Heber SIZE CAGE CODE DWG. NO. 01028 A 037Z3 REV A PAGE 1 OF 5 AMSC N/A 5935-E817-006 Provided by IHSNo
3、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01028 REV A PAGE 2 NOTES: 1. Dimensions are in inches; metric equivalents are in parentheses. 2. Metric equivalents are given for ref
4、erence purposes only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. No safety wire holes are required. 5. Series N, pin contact interface, 75 in accordance with figure 2. 6. Dimension is .812 inch (20.62 mm) across flats. FIGURE 1. General configuration. Provided
5、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01028 REV A PAGE 3 PLUG NOTES: 1. Dimensions are in inches. Metric equivalents are in parenthesis. 2. Metric equivalents are
6、given for information only. 3. Utilizes standard 50 body with 75 contact/air dielectric configuration. FIGURE 2. Interface, series N, pin contact, 75. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-
7、3990 SIZECAGE CODE DWG NO. A 037Z3 01028 REV A PAGE 4 ENGINEERING DATA: This document covers the requirements for radio frequency connectors accommodating special low smoke coaxial cables. Frequency range: 0-2.5 GHz. VSWR: 1.35 :1, maximum. Insertion loss: .13 dB at 2 GHz. REQUIREMENTS: These connec
8、tors shall conform to all the requirements of the latest issue of DSCC drawing 84148, figures 1 and 2 herein, and MIL-PRF-39012/5, and accommodate the cables listed in table I, with the following additions and exceptions. Electrical: Shall be in accordance with MIL-PRF-39012/5. Impedance: 75. Mechan
9、ical: Shall be in accordance with MIL-PRF-39012/5 with the following additions and exceptions. No safety wire holes are required. Environmental: Shall be in accordance with MIL-PRF-39012/5. TABLE I. Cable accommodation. Part or Identifying Number (PIN) 1/ 2/ Applicable cable 01028NBSA M17/229-00001
10、1/ These connectors have captivated center contacts. 2/ These connectors are assembled using the MIL-C-22520/5 crimp tool and using the following crimp dies: M22520/5-19 Closure A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER,
11、 COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01028 REV A PAGE 5 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed below have agreed to this drawing and a certificate of compliance
12、 has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ 01028NBSA 00795 3190-881 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and test are met. Vendor CAGE Vendor name number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
