1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changes in accordance with NOR 5905-R011-03. 15 JUL 03 K. Cottongim B Add manufacturer. Editorial changes throughout. 4 SEP 03 K. Cottongim C Inactive for new design. Revise to present DoD policy requirements. 12 Apr 05 Kendall A. Cottongim Notice of Inacti
2、vation for New Design DSCC Drawing 03013 is inactive for new design and is no longer used, except for replacement purposes. Use MIL-PRF-32159/12 Prepared in accordance with ASME Y14.100 Selected item drawing REV C C B C C REV STATUS OF PAGES PAGES 1 2 3 4 5 PMIC N/A PREPARED BY Andrew R. Ernst DEFEN
3、SE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY Andrew R. Ernst APPROVED BY Kendall A. Cottongim TITLE RESISTOR, CHIP, FIXED, FILM, ZERO-OHM, STYLE 0603 SIZE A CODE IDENT. NO. 037Z3 DWG NO. 03013 Original date of drawing 22 May 2003 REV C PAGE 1 OF 5 AMSC N/A 5905-E530 Provided by IHSNot for Resa
4、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03013 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a fixed, film, .060 X .030, zero-ohm, chip resistor. 1.2 Part o
5、r Identifying Number (PIN). The complete PIN is as follows and is available in wrap-around termination: 03013 - B | | | | Drawing Termination number (See 3.2.1) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards,
6、and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Establi
7、shed Reliability, Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-790 - Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specification. MIL-STD-1285 - Marking of Electrical and Electro
8、nic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict betwee
9、n the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirement
10、s shall be in accordance with MIL-PRF-55342 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-55342 and herein (see figure 1). 3.2.1 Termination material. The termination material shall be in accordan
11、ce with MIL-PRF-55342 and code letters B, C, G, or U. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03013 REV C PAGE 3 A B C D E .064 .006 .032 .005 .010/.033 .012 .
12、005 .015 .005 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. The pictorial view of the style above is given as representative of the item. Slight deviations from the outline shown, which are contained within the envelope, and do not alter the fun
13、ctional aspect of the device, are acceptable. FIGURE 1. Zero-ohm chip resistor style 0603. 3.3 Electrical characteristics. 3.3.1 Temperature range. The temperature range shall be -55C to +125C. 3.3.2 Resistance. The resistance shall not exceed 0.025 ohm. 3.4 Marking. Marking of the individual chip r
14、esistors is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, date, and lot codes. Inches .005 .006 .010 .012 .015 .032 .033 .064 mm 0.127
15、 0.152 0.254 0.305 0.381 0.813 0.838 1.626 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03013 REV C PAGE 4 3.5 Recycled, recovered, or environmentally preferable ma
16、terials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Certificate of compliance. A cert
17、ificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.7 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assu
18、rance program specified in MIL-PRF-55342 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Qualification inspection. Qualification inspection is not applicable to this document. 4.3 Product level qualification. The product level qualification specified in MIL-PRF-
19、55342 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection (established reliability level only and the parts per million reporting is not applicable) of MIL-PRF-55342. 4.5 Visu
20、al and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-55342. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requir
21、ements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite requirements. Packaging requirements are maintained by the
22、 Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the Military Services System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting t
23、he responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended for use in thick or thin film circuits where microcircuitry is intended; also in most surface mo
24、unt applications. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery and one copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of
25、 parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may
26、 be achieved online at Resistordla.mil or in writing to: DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBU
27、S, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03013 REV C PAGE 5 6.4 Suggested sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at Resistordla.mil or contact DSCC-VAT
28、, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN 03013-* Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address Termination styles B, C, G, U H0603CP*000(D03013) 56235 State of the Art, Incorporated 2470 Fo
29、x Hill Road State College, PA 16803-1797 Termination styles B RCWPM-0603-68 91637 Vishay Dale Electronics PO Box 609 Columbus, NE 68602-0609 Plant: Vishay Israel, Ltd Emek-Sara “B” Industrial Park Beer Sheva, Israel 84874 Termination styles B M0603XR000SB 57498 Vishay Thin Film 2160 Liberty Drive Niagara Falls, NY 14304 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
