1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Editorial changes and corrections throughout. Revised 3.2, 3.2.2, table I, and table III to agree with source specification. 21 May 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV A A A A A A A PAGES 1 2 3 4 5 6 7 PM
2、IC N/A PREPARED BY Ken Bernier DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 8 April 2005 CHECKED BY Ken Bernier TITLE CAPACITORS, TANTALUM, HYBRID, HERMETICALLY SEALED APPROVED BY Kendall Cottongim SIZE A CODE IDENT. NO. 037Z3 DWG NO. 04006 REV A PAGE 1 OF 7 AMSC N/A 5910-20
3、13-E10 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 04
4、006 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for shock hardened tantalum hybrid capacitors, hermetically sealed in welded tantalum case with glass to metal anode terminal. 1.2 General. The capacitor shall utilize a sintered tantalum anode and ruthenium oxide coated ca
5、thodes operating in aqueous electrolyte. 1.3 Part or Identifying Number (PIN). The complete PIN is as follows: 04006- -XX | | | |_ Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this drawing. Thi
6、s section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in
7、 sections 3 and 4 of this drawing, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of t
8、hese documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods for Electronic and Electrical Components Parts MIL-STD-1285 - Marking of Electrical and Electronic Parts (Copies of these documents are available online at http:/quick
9、search.dla.mil/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents a
10、re those cited in the solicitation or contract. ASSOCITATION CONNECTING ELECTRONIC INDUSTRIES (IPC) J-STD-002 - Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires (Copies of these documents are available online at www.IPC.org or from IPC, 3000 Lakeside Drive, Suite 309
11、S, Bannockburn, IL 60015.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable law
12、s and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 04006 REV A PAGE 3 3. REQUIREMENTS 3.1 Interface and p
13、hysical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Case. The case shall be tantalum. 3.1.2 Mass. 10 50 volt rated parts (see table I): 8 3 grams. 3.1.3 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both interna
14、lly and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.1.4 Storage temperature. The storage temperature shall be -62C to +130C. 3.1.5 Operating temperature range. The operati
15、ng temperature range shall be -55C to +125C. 3.2 Electrical characteristics. Note: These capacitors are designed for limited duration charge for high impact shock applications. Total time on charge shall not exceed 2 hours at +85C. 3.2.1 Rated voltage. The rated voltage shall be in accordance with t
16、able I at -55C to +85C or (+125C with voltage derating (see table I). 3.2.2 Surge voltage. Surge voltage shall be at 110 percent of rated voltage at +85C for a 1 minute maximum duration. The part shall be charged and discharged through a 1,000 ohm resistor. The capacitor shall not be visibly damaged
17、 and the electrical characteristics shall remain within specification. 3.2.3 Dielectric. The dielectric shall be an aqueous electrolyte. 3.2.4 DC leakage current. The maximum DC leakage current shall be as specified in table I following 5 minutes at the working voltage and at +23C 2C. 3.2.5 Capacita
18、nce. Capacitance shall be as specified in table I at 120 Hz and +23C 2C. 3.2.6 Capacitance tolerance. The capacitance tolerance shall be 20 percent at +23C 2C. 3.2.7 Equivalent series resistance (ESR). The maximum equivalent series resistance shall be as specified in table I at 1 kHz and +23C 2C. TA
19、BLE I. Electrical characteristics. DSCC drawing 04006- Capacitance in (uF) +85C rated voltage dc +125C rated Voltage dc Surge voltage dc ESR max (ohms) Leakage current max (A) 01 02 03 04 05 10,000 6,250 4,400 2,900 1,600 10 16 25 35 50 6 9.5 15 21 30 11 17.6 27.5 38.5 55 0.20 0.20 0.20 0.25 0.25 50
20、 50 50 50 50 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 04006 REV A PAGE 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general informa
21、tion only. FIGURE 1. Case dimensions and configuration. Inches mm .002 0.05 .010 0.25 .015 0.38 .025 0.64 .200 5.08 .341 8.66 .471 11.96 .500 12.70 .600 15.24 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, O
22、HIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 04006 REV A PAGE 5 3.3 Environmental testing. TABLE II. Environmental testing. Test Test method Condition Details Shock MIL-STD-202, method 213 E 0.5 ms at 1000g Vibration MIL-STD-202, method 204 E 12 sweeps/axis, 50g peak Vibration MIL-STD-202, method 214 I,
23、letter H 1.5 hours/axis, 29.28g rms Moisture resistance MIL-STD-202, method 106 6 V polarity Thermal shock MIL-STD-202, method 107 A Altitude MIL-STD-202, method 105 D 100,000 ft test 3.3.1 Thermal shock. Thermal shock test shall be as specified in table II. 3.3.2 Moisture resistance. Moisture resis
24、tance test shall be as specified in table II. 3.3.3 Hermetic Seal. The capacitor shall be hermetically sealed such that the case does not leak electrolyte or vent any gas when exposed to a vacuum, in accordance with MIL-STD-202, method 112, test condition C, procedure IIIa. 3.4 Physical testing. 3.4
25、.1 Shock . Shock test shall be as specified in table II. Note: These “shock-hardened” capacitors are designed for high impact and penetrating weapon environments. Testing has confirmed survivability at impacts over 10,000g. 3.4.2 Resistance to solder heat. The capacitor shall withstand solder dippin
26、g of the terminals at +260C for 10 seconds in accordance with MIL-STD-202, method 210, test condition B. The capacitor shall not be visibly damaged and the electrical characteristics shall not be affected. 3.4.3 Terminal strength. The capacitor terminals shall withstand a 5-pound pull test for 30 se
27、conds in accordance with MIL-STD-202, method 211, test condition A. The capacitor shall not be visibly damaged and the electrical characteristics shall not be affected. 3.4.4 Solderability. The terminations shall be solderable in accordance with J-STD-002. 3.4.5 Resistance to solvents. Resistance to
28、 solvents shall be in as specified in MIL-STD-202, method 215. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and
29、maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Manufacturer eligibility. To be eligible for listing as an approved source of supply a manufacturer shall perform all testing specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and
30、Maritime-VA. 3.7 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.8 Marking. Marking shall be in accordance with MIL-STD-1285, except the capacitor shall be marked with the PIN as specified herein (see 1.2),
31、the manufacturers name or Commercial and Government Entity (CAGE) code, date lot code and polarity. 3.9 Workmanship. The capacitor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking pe
32、rmitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 04006 REV A PAGE 6 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. In
33、spection of product for delivery shall consist of dc leakage, capacitance, and ESR before being shipped. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or
34、in-house personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system
35、 commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature, which may be hel
36、pful, but is not mandatory.) 6.1 Intended use. Hybrid capacitors covered by this drawing are intended mainly for use in defense electronic systems, avionics, and weapon systems. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements
37、 for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Requirements for notification of change of product to procuring activ
38、ity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on prod
39、ucts that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Sp
40、ecification for Electrodeposited Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Changes from previous issue. The margins of this specification are marked with vertical lines
41、 to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire conten
42、t irrespective of the marginal notations and relationship to the last previous issue. 6.6 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of
43、 this drawing may be achieved online at capacitorfilterdla.mil or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
44、m IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 04006 REV A PAGE 7 6.7 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be ob
45、tained online at capacitorfilterdla.mil or by contacting DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. TABLE III. Similar vendor PIN. DSCC PIN 04006- 1/ Similar vendor PIN 01 02 03 04 05 THQS2010103 THQS2016622 THQS202
46、5442 THQS2035292 THQS2050162 1/ Parts must be purchased to this DSCC PIN to assure all performance and tests are met. Vendor CAGE Vendor name and address 06MN5 Evans Capacitor Company 72 Boyd Avenue East Providence, RI 02914-1202 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
