1、REVISIONS LTR DESCRIPTION DATE APPROVED Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 PREPARED BY PMIC G Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 CHECKED BY T
2、ITLE Mary McWilliams APPROVED BY Richard Taylor CONNECTOR, PLUG, ELECTRICAL, RADIO FREQUENCY 2.4mm, PIN CONTACT, FOR SEMIRIGID CABLE SIZE CAGE CODE 037Z3 DWG. NO. 04017 Original date of drawing 30 November 2005 A REV PAGE 1 OF 9 AMSC N/A 5935-E744 Provided by IHSNot for ResaleNo reproduction or netw
3、orking permitted without license from IHS-,-,-NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Metric equivalents are in parentheses. 4. Dimension .400 (10.16) is the largest overall envelope of the connector. 5. Wrench flats to accommodate standard wrench
4、 in accordance with FED-STD-H28, appendix 10. 6. Dimension “A” defines the maximum length of connector when assembled to cable. 7. When applicable, three holes .016 (0.41 mm) minimum diameter, equally spaced, are required for safety wiring after mating. Location on the coupling nuts optional. 8. All
5、 threads shall conform to FED-STD-H28. 9. Series 2.4mm, pin contact interface in accordance with figure 2. 10. All undimensioned pictorial representations are for reference purposes only. FIGURE 1. General configuration. SIZE CAGE CODE DWG NO. 037Z3 04017 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 39
6、90, COLUMBUS, OH 43218-3990 A REVPAGE2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTES.: 1. Insulator to be flush to -.003 below reference plane. 2. With coupling nut biased in the forward direction. 3. Dimensions are in inches. 4. Metric equiv
7、alents are given for information only. FIGURE 2. Interface dimensions (2.4 mm). SIZE CAGE CODE DWG NO. 037Z3 04017 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE3 Inches mm Inches mm .002 0.05 .186 4.72 .003 0.08 .187 4.75 .010 0.25 .191 4.85 .014 0.35 .249 6.32 .0
8、196 0.498 .251 6.37 .0206 0.523 .290 7.37 .0409 1.039 .290 7.37 .0415 1.054 .053 1.35 .057 1.45 .073 1.85 .094 2.39 .095 2.41 .096 2.44 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dash number and applicable cable. Dimension 2/ A PIN Appl
9、icable cable 1/ Maximum before assembly Maximum after assembly Dimension B CATEGORY E FIELD REPLACEABLE (STANDARD ASSEMBLY TOOL KIT) 3/ 4/ 5/ 7/ 8/ 04017ZSPA-2 04017ZCGA-2 04017ZSPA-3 6/ 04017ZCGA-3 6/ M17/133-RG405* M17/133-00001 through M17/133-00018 Not applicable .828 (21.03 mm) maximum Not appl
10、icable 04017ZSPA-4 04017ZCGA-4 04017ZSPA-5 6/ 04017ZCGA-5 6/ M17/133-RG405* M17/133-00001 through M17/133-00018 Not applicable .460 (11.68 mm) maximum .215 (5.46) .010 (0.25) * Cable to be used when performing test requiring cable. 1/ MIL-DTL-17 cables are specified by the basic number. The latest v
11、ersion of each cable shall be applicable. 2/ Dimension A determines the closeness of a bend in the cable to the rear of the connector. 3/ These connectors have captivated center contacts. 4/ For logistics purposes, only connectors with safety wire holes will be stocked. 5/ Coupling nuts shall be cor
12、rosion-resistant steel with a passivated finish in accordance with SAE AMS-2700 type 2 for connectors with corrosion-resistant steel bodied connectors. 6/ No safety wire holes. 7/ Kit number Amphenol 901-2500, or equivalent. 8/ All corrosion-resistant steel-bodied connectors shall be Gold plated in
13、accordance with ASTM B488, type II code C, class 1.27, over 50 micro inches (1.27 micro meters) minimum of nickel in accordance with SAE-AMS-QQ-N-290 at least in the area of solder attachment. SIZE CAGE CODE DWG NO. 037Z3 04017 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990
14、A REVPAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Cable Dimension “A“M17/133-RG405 M17/133-00001 through M17/133-00018 .070 .005 (1.78 0.13) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parenthesis and are given for infor
15、mation only. 3. Tapering of center conductor is optional. FIGURE 3. Cable stripping dimensions for category E connectors. SIZE CAGE CODE DWG NO. 037Z3 04017 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE5 Provided by IHSNot for ResaleNo reproduction or networking p
16、ermitted without license from IHS-,-,-ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 50 GHz. Voltage rating: The voltage rating shall be in accordance with table II. TABLE II. Voltage rating. Cable Voltage maximum (at sea level) Voltage maximum (70,000 feet) M17/133-RG405 M17/13
17、3-00001 through M17/133-00018 V rms335 V rms85 Temperature rating: -65C to +165C. REQUIREMENTS: Dimensions and configuration: See figures 1 and 2. Force to engage and disengage: Longitudinal force: Not applicable. Torque: 2 inch-ounces maximum. Coupling proof torque: 15 inch-pounds, minimum. Safety
18、wire hole tear out: 15 pounds, minimum. Inspection conditions: For each test of threaded coupling connector where the test is performed on mated pairs, the pairs shall be torqued to 7 to 10 inch-pounds. Mating characteristics: See figure 2. Hermetic seal: Not applicable. Leakage (pressurized connect
19、ors): Not applicable. Insulation resistance: Method 302, test condition B of MIL-STD-202, 5,000 megohms, minimum. Center contact retention: 6 pounds minimum axial force. Radial torque: Not applicable. Corrosion (salt spray): Method 101, test condition B of MIL-STD-202. SIZE CAGE CODE DWG NO. 037Z3 0
20、4017 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Voltage standing wave ratio (VSWR): From 0.5 to 50 GHz, or approximately 80 percent of upper cutoff frequency of t
21、he cable, whichever is lower. Cables VSWRM17/133-RG405 M17/133-00001 1.07 + 0.01 F (GHz) through M17/133-00018 Swept frequency VSWR test setup: Item 6: VSWR shall be less than 1.025 + .002 F (F in GHz). Item 16: VSWR shall be less than 1.025 + .002 F (F in GHz). Second step of VSWR checkout procedur
22、e: VSWR shall be less than 1.080 + .005 F (F in GHz). Connector durability: 500 cycles, minimum at 12 cycles per minute maximum. The connector shall meet the mating characteristics and force to engage and disengage requirements. Contact resistance: In milliohms, maximum. Initial After environmentCen
23、ter contact: 3.0 4.0 Outer contact: 2.0 Not applicable Outer cable conductor to body: 0.5 1/ Not applicable Dielectric withstanding voltage at sea level: Method 301 of MIL-STD-202. Cables V rmsM17/133-RG405 1,000 M17/133-00001 through M17/133-00018 Vibration, high frequency: Method 204, test conditi
24、on D of MIL-STD-202, except the method of mounting shall be approved by the preparing activity. No discontinuity permitted. Shock (specified pulse): Method 213, test condition I of MIL-STD-202. Thermal shock: Method 107, test condition B of MIL-STD-202, except test high temperature shall be +115C. M
25、oisture resistance: Method 106 of MIL-STD-202. No measurements at high humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. 1/ Five milliohms is permissible for passivated steel bodied connectors only. SIZE CAGE CODE DWG NO. 037Z3 04017 DEFENSE
26、SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Corona level: Altitude: 70,000 feet. Cables Volts (minimum)M17/133-RG405 250 M17/133-00001 through M17/133-00018 RF high potent
27、ial withstanding voltage: Frequency: 5 MHz to 7.5 MHz. Leakage current: Not applicable. Cables V rmsM17/133-RG405 670 M17/133-00001 through M17/133-00018 Cable retention force: The cable retention force shall be as specified in table III. TABLE III. Cable retention force. Cable Pounds(minimum) Torqu
28、e 1/ inch-ounce M17/133-RG405 M17/133-00001 through M17/133-00018 30 16 1/ Torque to be applied 4 inches maximum from the end of the connector. Reverse bend not applicable. Coupling mechanism retention force: 60 pounds minimum. RF leakage: -90 dB minimum, tested at a frequency between 2 and 3 GHz. R
29、F insertion loss: dB maximum = .03 x freq GHz. Test frequency at a frequency between .5 to 50 GHz. Part or Identifying Number (PIN): See table I. SIZE CAGE CODE DWG NO. 037Z3 04017 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE8 Provided by IHSNot for ResaleNo repr
30、oduction or networking permitted without license from IHS-,-,-Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC
31、VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 04017ZSPA-2 SF1603-6003 04017ZCGA-2 1603-4002 04017ZSPA-3 SF1603-6004 04017ZCGA-3 1603-4003 04017ZSPA-4 SF1603-6005 04017ZCGA-4 1603-4004 04017ZSPA-5 SF1603-6006 04017ZCGA-5 95077 1603-4005 1/ Parts must be purchased to this DSCC PIN
32、to assure that all performance requirements and tests are met. Vendor CAGE Vendor Name and number address95077 S/V Microwave, Inc. 2400 Centrepark West Dr. West Palm Beach, FL 33409 SIZE CAGE CODE DWG NO. 037Z3 04017 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
