1、 REVISIONS LT DESCRIPTION DATE APPROVED A Added approved source of supply. Revised table IV. Added 6.4. Removed table from 3.3.1. 17 April 2008 Michael A. Radecki B Added an approved source of supply. 22 January 2009 Michael A. Radecki C Changed address of vendor B. 1 July 2010 Michael A. Radecki D
2、Removed an approved source of supply. 12 June 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV D D D D D D D D PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY MICHAEL A. RADECKI DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 3
3、 January 2005 CHECKED BY MICHAEL A. RADECKI TITLE CAPACITORS, FIXED, CERAMIC, CHIP, 0805, HIGH FREQUENCY, BP APPROVED BY KENDALL A. COTTONGIM SIZE A CODE IDENT. NO. 037Z3 DWG NO. 05001 REV D PAGE 1 OF 8 AMSC N/A 5910-2013-E14CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND
4、MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05001 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55681 describe the r
5、equirements for ceramic, chip. 1.2 Part or Identifying Number (PIN) The complete PIN is as follows: 05001- 2R0 B C Z - Drawing number Capacitance value (see 1.2.1) Voltage (see 1.2.2) Capacitance tolerance (see 1.2.3) Termination finish (see 1.2.4) Group C testing option (see 1.2.5) 1.2.1 Capacitanc
6、e value. The nominal capacitance value, expressed in picofarads (pF) is identified by a three digit number; the first two digits represent significant figures and the last digit specifies the number of zeros to follow. When the nominal value is less than 10 pF, the letter “R” is used to indicate the
7、 decimal point and the succeeding digit(s) of the group represent significant figure(s). 1R0 indicates 1.0 pF; R75 indicates .75 pF; and 0R5 indicates 0.5 pF. See table IV for values. 1.2.2 Voltage. The rated voltage for continuous operation at +125C is identified by a single letter as shown in tabl
8、e I. TABLE I. Rated voltage. Symbol Rated voltage (volts, dc) Z 25 A 50 B 100 C 200 K 250 1.2.3 Capacitance tolerance. The capacitance tolerance is identified by a single letter in accordance with table II. TABLE II. Capacitance tolerance. Symbol Capacitance tolerance () A .05 pF B .1 pF C .25 pF D
9、.50 pF F 1 percent G 2 percent J 5 percent K 10 percent M 20 percent 1.2.4 Termination finish. Termination finish is identified by a single letter as shown in table III. TABLE III. Termination finish. Symbol Termination finish M Palladium-silver Z Base metallization-barrier metal-tinned (tin/lead al
10、loy, with a minimum of 4 percent lead) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05001 REV D PAGE 3 1.2.5 Group C testing option. To require MIL-PRF-55681 group
11、C testing, use the appropriate letter from the table below. If group C testing is not desired, leave this location blank. NOTE: Ordering group C options that contain a 2,000 hour life test may extend the processing time by 90 days or more. Letter Group C testing option C Full group C L 2,000 hour li
12、fe test only M 1,000 hour life test only H Low voltage humidity only N/A No group C testing. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this spec
13、ification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are li
14、sted. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contrac
15、t (See 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55681 - Capacitor, Chip, Multiple Layer, Fixed, Unencapsulated, Ceramic Dielectric, Established Reliability and Non-Established Reliability, General Specification For. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Co
16、mponent Parts, Test Methods for. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of preceden
17、ce. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption ha
18、s been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55681, and as specified herein. These capacitors shall be capable of meeting all electrical, environmental, and mechanical requirements of MIL-PRF-55681, unless otherwise stat
19、ed. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-55681 and herein (see figure 1). 3.2.1 Tin plated finishes. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes are acceptable provided that the min
20、imum lead content is 4 percent (see 6.4). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05001 REV D PAGE 4 T W Y L NOTES: 1. Dimensions are in inches. 2. Metric equi
21、valents are given for general information only. FIGURE 1. Case dimensions and configuration. 3.3 Electrical characteristics. 3.3.1 Dielectric type. The dielectric type shall be BP (30 ppm/C) ceramic in accordance with MIL-PRF-55681. 3.3.2 Capacitance. Capacitance shall be in accordance with table IV
22、 when measured in accordance with method 305 of MIL-STD-202. The following conditions shall apply: 1,000 pF 1 MHz 50 kHz 1 V rms .2 V rms 1,000 pF 1 kHz 50 Hz 1 V rms .2 V rms Inches mm .008 0.20 .010 0.25 .020 0.51 .049 1.24 .055 1.40 .079 2.00 Dimensions L .008 W .008 T Max Y .01 .079 .049 .055 .0
23、20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05001 REV D PAGE 5 3.3.3 Dissipation factor (+25C). When measured at the frequency and voltage specified in 3.3.2, t
24、he dissipation factor shall be 0.05 percent. 3.3.4 Insulation resistance. At +25C: minimum of 100,000 megohms or 1,000 megohm-microfarads, whichever is less. At +125C: minimum of 1,000 megohms or 10 megohm-microfarads, whichever is less. 3.4 Solderability. In accordance with MIL-PRF-55681, except th
25、e sample size shall be 5 pieces with zero defectives permitted. 3.5 Moisture resistance. In accordance with MIL-PRF-55681, with the following exceptions: a. Polarizing voltage shall be rated voltage. b. Testing may be performed on chips with a larger width and/or length as long as they are cut from
26、the same wafer(s) as those used for production. 3.6 Marking. As a minimum, marking shall be on the package due to the small size of the chips. The package marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in paragraph 1.2 with manufacturers name or CAGE code and
27、date code. The manufacturer may, at their option, mark some information on the chips. Suggested marking is the 2 digit EIA capacitance code. 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-55681 Qualified Product
28、s List for at least one part, or perform the group A and group C inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approve
29、d source of supply. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes econ
30、omically advantageous life cycle costs. 3.10 Workmanship. In accordance with MIL-PRF-55681. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist o
31、f all tests specified in group A of MIL-PRF-55681. ESR testing and PPM testing and calculation are not applicable. When optional group C testing is requested, terminal strength and series resonance are not applicable. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements s
32、hall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Invento
33、ry Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the resp
34、onsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05001 REV D PAGE 6 6. NOTES (This section contains information of a general or explanatory
35、nature that may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is inte
36、nded exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design.
37、 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufa
38、cturer. c. Requirements for notification of change of product to acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by a contractor-prepared specification or drawing. 6.4
39、 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such mate
40、rials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electro
41、deposited Coatings of Tin). 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at capacitorfilterdla.m
42、il or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance
43、in the use of this drawing may be obtained online at capacitorfilterdla.mil or by contacting DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. 6.7 Changes from previous issue. The margins of this specification are marked w
44、ith vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on
45、 the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05001 REV D PAG
46、E 7 TABLE IV. Electrical characteristics. DSCC Drawing 05001- 1/ Capacitance pF Available tolerances ATC Vendor A Available voltages VISHAY 2/ Vendor B Available voltages Z A B C K Z A B C K 25 50 100 200 250 25 50 100 200 250 0R1- - - - .1 A, B 0R2- - - - .2 A, B 0R3- - - - .3 A, B, C 0R4- - - - .4
47、 A, B, C 0R5- - - - .5 A, B, C 0R6- - - - .6 A, B, C 0R7- - - - .7 A, B, C 0R8- - - - .8 A, B, C 0R9- - - - .9 A, B, C 1R0- - - - 1 A, B, C 1R1- - - - 1.1 A, B, C, D 1R2- - - - 1.2 A, B, C, D 1R3- - - - 1.3 A, B, C, D 1R4- - - - 1.4 A, B, C, D 1R5- - - - 1.5 A, B, C, D 1R6- - - - 1.6 A, B, C, D 1R7-
48、 - - - 1.7 A, B, C, D 1R8- - - - 1.8 A, B, C, D 1R9- - - - 1.9 A, B, C, D 2R0- - - - 2 A, B, C, D 2R1- - - - 2.1 A, B, C, D 2R2- - - - 2.2 A, B, C, D 2R4- - - - 2.4 A, B, C, D 2R7- - - - 2.7 A, B, C, D 3R0- - - - 3 A, B, C, D 3R3- - - - 3.3 A, B, C, D 3R6- - - - 3.6 A, B, C, D 3R9- - - - 3.9 A, B, C, D
