1、 REVISIONS LT DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawingREV STATUS REV OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY John Bonitatibus DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY Patrick Kyne Original date of drawing 17 Fe
2、bruary 2009 APPROVED BY Michael A. Radecki TITLE CAPACITORS, FIXED, METALLIZED PLASTIC DIELECTRIC, DC, IN NONMETAL CASES SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09007 REV PAGE 1 OF 7 AMSC N/A 5910-E423Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFE
3、NSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09007 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for metallized polycarbonate capacitors screened to MIL-PRF-55514. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 0
4、9007 -001 K | | | Drawing Dash number Capacitance number (see table I) tolerance (see 3.2.4) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this spec
5、ification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they
6、are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or c
7、ontract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55514 - Capacitors, Fixed, Plastic (or Metallized Plastic) Dielectric, DC or DC-AC, In Non-Metal Cases, Non-Established Reliability and Established Reliability, General Specification for. (Copies of these documents are available online at http:/a
8、ssist.daps.dla.mil/quicksearch or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cite
9、d herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physic
10、al dimensions shall be as specified in MIL-PRF-55514 and herein (see figure 1 and table I). 3.1.1 Case type. Molded or preformed. 3.1.2 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall n
11、ot exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.1.3 Operating temperature range. The operating temperature range shall be -55C to +85C. Will operate to +125C when properly derated to 50 percent of +85C rated voltage. Provided by IHSNot for R
12、esaleNo reproduction or networking permitted without license from IHS-,-,-Style “A” DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09007 REV PAGE 3 Style “B” Inches mm .001 0.03 .004 0.10 .015 0.38 .020 0.51 .025 0.64 .045 1.14 .090 2.29 .100 2.54 .190 4.83 .200 5
13、.08 1.250 31.75 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information. 3. Unless otherwise specified, tolerance is .010 inch (0.25 mm). 4. For flush mounting .078 inch (1.98 mm) printed-circuit hole diameter is required to clear shoulder. 5. Lead length may be a
14、 minimum of one inch (25.4 mm) long for use in tape and reel packaging, when specified in the ordering data. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.2 Electrical characteristics. 3.2.1 Rated voltage.
15、See table I for +85C ratings. For +125C operation, linearly derate +85C rating by 50 percent. 3.2.2 Dielectric type. Metallized polycarbonate. 3.2.3 Dielectric withstanding voltage (DWV). In accordance with MIL-PRF-55514, except the surge current shall be limited to 1 ampere, maximum. 3.2.4 Capacita
16、nce tolerance (see table I). F = 1 percent, G = 2 percent, J = 5 percent, and K = 10 percent. 3.2.5 Dissipation factor (DF). In accordance with MIL-PRF-55514, except dissipation factor shall not exceed .3 percent. 3.3 Preconditioning. Not applicable. 3.4 Burn-in. In accordance with MIL-PRF-55514, ex
17、cept DC: 48 hours at +125C at 1.4 times the derated +125C dc voltage rating. The current to each capacitor shall be limited to 1 ampere maximum by a series resistor. AC: not applicable. 3.5 Resistance to soldering heat. In accordance with MIL-PRF-55514, except that spacers or standoffs of .25 inch (
18、6.4 mm) are required. 3.6 Marking. In accordance with MIL-PRF-55514, except the capacitor shall be marked with the PIN as specified herein (see 1.2), the manufacturers symbol or Commercial and Government Entity (CAGE) code, and date lot codes. Minimum marking as shown in the following example will b
19、e permitted. Full marking shall be included on the package. CAPACITANCETOLERANCE (SEE 3.2.4) DASH NUMBER(SEE TABLE I)DRAWINGNUMBER Note: Manufacturers symbol or CAGE code, date code and lot symbol in accordance with MIL-PRF-55514 shall be marked on the reverse side. 3.7 Manufacturer eligibility. To
20、be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-55514 Qualified Products Database for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.8 Recycl
21、ed, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cyc
22、le costs. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.10 Workmanship. The capacitor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. DEFENSE
23、 SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09007 REV PAGE 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09007 REV PAGE 5 TABLE I.
24、Electrical characteristics and dimensions. DSCC Drawing Dimensions 2/ 09007- 1/ Capacitance Value in F Rated voltage at +85C in volts Capacitance Tolerance (see 3.2.4) T H L LS Style “A” 3/ 001- .033 50 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 002- .039 50 F, G, J, K .090 (2.29) .2
25、00 (5.08) .190 (4.83) .200 (5.08) 003- .047 50 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 004- .056 50 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 005- .022 75 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 006- .027 75 F, G, J, K .090 (2.29) .200 (5.08) .1
26、90 (4.83) .200 (5.08) 007- .01 100 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 008- .012 100 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 009- .015 100 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 010- .018 100 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83)
27、 .200 (5.08) 011- .0068 150 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 012- .0082 150 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 013- .0039 200 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 014- .0047 200 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .20
28、0 (5.08) 015- .0056 200 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 016- .001 250 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 017- .0012 250 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 018- .0015 250 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.
29、08) 019- .0018 250 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 020- .0022 250 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 021- .0027 250 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08) 022- .0033 250 F, G, J, K .090 (2.29) .200 (5.08) .190 (4.83) .200 (5.08)
30、Style “B” 023- .068 50 F, G, J, K .095 (2.41) .245 (6.22) .295 (7.49) .200 (5.08) 024- .082 50 F, G, J, K .095 (2.41) .245 (6.22) .295 (7.49) .200 (5.08) 025- .10 50 F, G, J, K .095 (2.41) .245 (6.22) .295 (7.49) .200 (5.08) 026- .12 50 F, G, J, K .095 (2.41) .295 (7.49) .295 (7.49) .200 (5.08) 027-
31、 .15 50 F, G, J, K .095 (2.41) .295 (7.49) .295 (7.49) .200 (5.08) 028- .18 50 F, G, J, K .095 (2.41) .295 (7.49) .295 (7.49) .200 (5.08) 029- .22 50 F, G, J, K .095 (2.41) .395 (10.03) .395 (10.03) .300 (7.62) 030- .27 50 F, G, J, K .095 (2.41) .395 (10.03) .395 (10.03) .300 (7.62) 031- .33 50 F, G
32、, J, K .095 (2.41) .395 (10.03) .395 (10.03) .300 (7.62) 032- .39 50 F, G, J, K .095 (2.41) .395 (10.03) .395 (10.03) .300 (7.62) 033- .47 50 F, G, J, K .145 (3.68) .395 (10.03) .395 (10.03) .300 (7.62) 034- .56 50 F, G, J, K .145 (3.68) .395 (10.03) .395 (10.03) .300 (7.62) 035- .78 50 F, G, J, K .
33、195 (4.95) .395 (10.03) .395 (10.03) .300 (7.62) 036- .82 50 F, G, J, K .195 (4.95) .395 (10.03) .395 (10.03) .300 (7.62) 037- 1.00 50 F, G, J, K .195 (4.95) .395 (10.03) .395 (10.03) .300 (7.62) 1/ The complete PIN will include an additional symbol to indicate capacitance tolerance (see 1.2). 2/ Me
34、tric equivalents are in parentheses and are for general information only. 3/ Care must be taken during wave soldering to assure that style A capacitors are not damaged due to overheating. During the wave soldering operation, the style A capacitors shall not be exposed to conditions in excess of the
35、resistance to soldering heat requirements of MIL-PRF-55514. 4. VERIFICATION 4.1 Conformance inspection. 4.1.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection of MIL-PRF-55514. Group B inspection of MIL-PRF-55514 shall be performed when s
36、pecified on the purchase order (see 6.2c). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09007 REV PAGE 6 5. PACKAGING 5.1 Packaging. For acquisition purposes, the p
37、ackaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are ma
38、intained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or
39、 by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qu
40、alified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the produc
41、t covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspecti
42、on data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for group B testing (see 4.1.1). d. Requirements for notification of change of product to the acquiring activity, if applicable. e. Requirements for pac
43、kaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on prod
44、ucts that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Sp
45、ecification for Electrodeposited Coatings of Tin). 6.4 Soldering. These capacitors are heat sensitive. Vapor phase soldering is not recommended. For applications that require wave soldering that exceeds 5 seconds in duration, it is recommended that a spacer or standoff be used. 6.5 Replaceability. C
46、apacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 03
47、7Z3 DWG NO. 09007 REV PAGE 7 6.6 Cross reference to MIL-PRF-55514/8. This drawing replaces MIL-PRF-55514/8. Cross references are listed in table II. TABLE II. DSCC Drawing 09007 PIN to MIL-PRF-55514/8 PIN cross reference. DSCC Drawing 09007- 1/ MIL-PRF-55514/8 2/ DSCC Drawing 09007- 1/ MIL-PRF-55514
48、/8 2/ 001- CFR12RRA333- 023- CFR16RRA683- 002- CFR12RRA393- 024- CFR16RRA823- 003- CFR12RRA473- 025- CFR16RRA104- 004- CFR12RRA563- 026- CFR16RRA124- 005- CFR12RRG223- 027- CFR16RRA154- 006- CFR12RRG273- 028- CFR16RRA184- 007- CFR12RRB103- 029- CFR16RRA224- 008- CFR12RRB123- 030- CFR16RRA274- 009- C
49、FR12RRB153- 031- CFR16RRA334- 010- CFR12RRB183- 032- CFR16RRA394- 011- CFR12RRH682- 033- CFR16RRA474- 012- CFR12RRH822- 034- CFR16RRA564- 013- CFR12RRC392- 035- CFR16RRA684- 014- CFR12RRC472- 036- CFR16RRA824- 015- CFR12RRC562- 037- CFR16RRA105- 016- CFR12RRK102- 017- CFR12RRK122- 018- CFR12RRK152- 019- CFR12RR
