1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Updated table I. Added 100V and 125V PINs and corrected errors in table II. 29 May 2012 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV A A A A A A A PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Ken Ber
2、nier DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 16 February 2010 CHECKED BY Ken Bernier TITLE CAPACITORS, TANTALUM, HERMETICALLY SEALED APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 10011 REV A PAGE 1 OF 7 AMSC N/A 5910-2012-E08CURRENT
3、 DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10011 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the complete requi
4、rements for tantalum electrolytic (nonsolid) electrolyte, fixed capacitors, in tantalum cases, insulated and uninsulated. 1.2 General. The capacitor shall utilize a sintered tantalum anode and a proprietary coated cathode operating in aqueous electrolyte. The components shall be hermetically sealed
5、in a welded tantalum case with a glass-to-metal anode terminal seal. 1.3 Part or Identifying Number (PIN). The complete PIN is as follows: 10011 -XX Drawing Dash number Number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of
6、 this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specifie
7、d requirements of documents in sections 3 and 4 of this specification, whether or not they are listed herein. 2.2 Government documents. 2.2.1 Specifications standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Un
8、less otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts, Test Methods for. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents ar
9、e available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this
10、 document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimens
11、ions shall be as specified herein (see figure 1). 3.1.1 Case. The case shall be tantalum. 3.1.2 Mass. See figure 1. 3.1.3 Pure tin. The use of pure tin as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 pe
12、rcent by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3) 3.1.4 Storage temperature. The storage temperature shall be -62C to +130C. 3.1.5 Operating temperature range. The operating temperature range shall be -55C to +85C or (+125C with voltage de-rating (see table I).
13、Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10011 REV A PAGE 3 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be in accordance with table I at -55C to +85C or (+125C with voltage de-rating). 3.2.2
14、Surge voltage. The test shall be 1000 cycles at 110% of rated voltage at +85C 3C. Each cycle shall consist of a 30 2 second surge voltage application followed by 330 2 second discharge period. The part shall be charged and discharged through a 100 ohm resistor. The capacitor shall not be visibly dam
15、aged and the electrical characteristics shall remain within specification. 3.2.3 Dielectric. Ta 2 O 5. 3.2.4 DC leakage current. The maximum DC leakage current shall be as specified in table I following 5 minutes at the working voltage and +25C. 3.2.5 Capacitance. Capacitance shall be as specified i
16、n table I at 120 Hz and +25C, 20 percent. 3.2.6 Capacitance tolerance. The capacitance tolerance shall be 20 percent at +25C. 3.2.7 Equivalent series resistance (ESR). The maximum equivalent series resistance shall be as specified in table I at 1 kHz and +25C. TABLE I. Electrical characteristics. DS
17、CC drawing PIN 10011- Capacitance in (F) +85C rated voltage dc +125C rated voltage dc ESR max (ohms) +25C, 1 kHz Leakage current max (A) +25C Case code 01 72000 25 15 0.035 350 C 02 54000 25 15 0.035 300 C 03 48000 25 15 0.045 200 B 04 36000 25 15 0.045 200 B 05 24000 25 15 0.060 150 A 06 18000 25 1
18、5 0.060 150 A 07 24000 50 30 0.035 400 C 08 16000 50 30 0.045 270 B 09 8000 50 30 0.075 170 A 10 12000 63 40 0.035 400 C 11 8000 63 40 0.055 270 B 12 4000 63 40 0.100 170 A 13 9000 80 50 0.040 500 C 14 8200 80 50 0.040 500 C 15 6000 80 50 0.065 400 B 16 3000 80 50 0.100 300 A 17 5700 100 65 0.050 50
19、0 C 18 3800 100 65 0.065 400 B 19 1900 100 65 0.085 300 A 20 3300 125 85 0.075 500 C 21 2200 125 85 0.085 400 B 22 1100 125 85 0.100 300 A Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10011 REV A PAGE 4 TABLE II. Dimensions Case
20、 Code Diameter Height L2 L1 T Weight (grams) typical A 1.400 0.005 (35.56 0.127) 0.350 0.015 (8.89 0.381) 0.500 (12.7) 0.500 (12.7) 0.40 0.015 (10.16 0.381) 48.0 B 1.400 0.005 (35.56 0.127) 0.488 0.015 (15.60 0.381) 0.500 (12.7) 0.500 (12.7) 0.40 0.015 (10.16 0.381) 73.0 C 1.400 0.005 (35.56 0.127)
21、0.615 0.015) (15.6 0.381) 0.500 (12.7) 0.500 (12.7) 0.40 0.015 (10.16 0.381) 95.0 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Case dimensions and configuration. Inches mm .005 0.127 .015 0.381 .350 8.89 .400 10.16 .488 12.40 .615 15.62
22、1.400 35.56 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10011 REV A PAGE 5 3.3 Environmental testing. TABLE III. Environmental testing. Test Test method Condition Detai
23、ls Shock MIL-STD-202, method 213 G 11 mS at 50 g Vibration MIL-STD-202, method 204 D 12 sweeps/axis, 20 g peak Vibration MIL-STD-202, method 214 I, letter D 1.5 hours/axis, 12 g rms Moisture resistance MIL-STD-202, method 106 6 V polarity Thermal shock MIL-STD-202, method 107 A Altitude MIL-STD-202,
24、 method 105 D 100,000 ft test 3.3.1 Thermal shock. Thermal shock test shall be as specified in table III. 3.3.2 Moisture resistance. Moisture resistance test shall be as specified in table III. 3.3.3 Hermetic seal. The capacitor shall be hermetically sealed such that the case does not leak electroly
25、te or vent any gas when exposed to a vacuum, in accordance with MIL-STD-202, method 112, test condition C, procedure IIIa. 3.3.4 Altitude. The altitude test shall be as specified in table III. 3.4 Physical testing. 3.4.1 Shock . Shock test shall be as specified in table II. 3.4.3 Resistance to solde
26、r heat. The capacitor shall withstand solder dipping of the terminals at +260C for 10 seconds in accordance with MIL-STD-202, method 210, test condition B. The capacitor shall not be visibly damaged and the electrical characteristics shall not be affected. 3.4.4 Terminal strength. The capacitor term
27、inals shall withstand a 5-pound pull test for 30 seconds in accordance with MIL-STD-202, method 211, test condition A. The capacitor shall not be visibly damaged and the electrical characteristics shall not be affected. 3.4.5 Solderability. The terminals shall be solderable per MIL-STD-202, method 2
28、08. 3.4.6 Resistance to solvents. Resistance to solvents shall be as specified in MIL-STD-202, method 215. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the ma
29、terial meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Manufacturer eligibility. To be eligible for listing as an approved source of supply a manufacturer shall perform all testing as specified herein on a sample of parts as
30、 agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.7 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply for the testing performed in 3.6 and any parameter or test not covered by testing. 3.8 Marking.
31、 Marking shall be in accordance with MIL-STD-1285, except the capacitor shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, date lot code and polarity. 3.9 Workmanship. The capacitor shall be uniform in quality and free
32、from any defects that will affect life, serviceability, or appearance. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10011 REV A PAGE 6 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 C
33、onformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of dc leakage, capacitance, ESR, and the environmental tests of table III. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance for tab
34、le III requirements in lieu of performing table III tests (see 6.2c). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, thes
35、e personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging dat
36、a retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature, which may be helpful, but is not mandato
37、ry.) 6.1 Intended use. Capacitors covered by this drawing are intended mainly for use in defense electronic systems, avionics, and weapon systems. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of th
38、e conformance inspection data or certificate of compliance that parts have passed the conformance inspection paragraph with each shipment of parts by the manufacturer. c. Requirements for sampling for table III tests when conformance inspection data is required. d. Requirements for packaging and pac
39、king. e. Requirements for notification of change of product to procuring activity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacturer. Tin whiskers may occur anytime from a day to year
40、s after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have been shown to inhibit the growth of tin
41、whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Changes f
42、rom previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors ar
43、e cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the previous issue. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10011 REV A PAGE 7
44、 6.6 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at capacitorfilterdla.mil or if in writing to: D
45、LA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. 6.7 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this dr
46、awing may be obtained online at capacitorfilterdla.mil, or by contacting DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. TABLE IV. Similar vendor PIN. 1/ DSCC drawing PIN 10011- VISHAY Vendor A Similar vendor PIN 1 HE3C7
47、23M025BZSS 2 HE3C543M025BZSS 3 HE3A483M025BZSS 4 HE3B363M025BZSS 5 HE3A243M025BZSS 6 HE3A183M025BZSS 7 HE3C243M050BZSS 8 HE3B163M050BZSS 9 HE3B802M050BZSS 10 HE3C123M063BZSS 11 HE3B802M063BZSS 12 HE3A402M063BZSS 13 HE3C902M080BZSS 14 HE3C822M080BZSS 15 HE3B602M080BZSS 16 HE3A302M080BZSS 17 HE3C572M1
48、00BZSS 18 HE3B382M100BZSS 19 HE3A192M100BZSS 20 HE3C332M125BZSS 21 HE3B222M125BZSS 22 HE3A112M125BZSS 1/ Parts must be purchased to this DSCC PIN to assure all performance and tests are met. Vendor Vendor CAGE Vendors name and address A 05079 Vishay Tansitor 2813 West Road Bennington VT 05201 Provided by IHSNot for Resale-,-,-
