1、 AMSC N/A 5935-E838-004 REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 PMIC G PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Jeremy Funk Original date of drawing 04 September 2013 CHECKED BY TITLE Jeremy Funk CONNECTOR, ELECTRICAL, COAX
2、IAL, RADIO FREQUENCY, SOCKET CONTACT SERIES SMPS APPROVED BY Abdonasser Abdouni SIZE CAGE CODE DWG. NO. 10022 A 037Z3 REV PAGE 1 OF 5 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networki
3、ng permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10022 REV PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990
4、SIZE CAGE CODE DWG NO. A 037Z3 10022 REV PAGE 3 Inches mm .042 1.07 .063 1.60 .077 1.78 .104 2.64 .245 6.22 PIN Cable accommodation Cable overall diameter 10022 M17/151-00001 1/ .047 inch 1/ These connectors accept all cables listed on the reference specification sheet. NOTES: 1. Dimensions are in i
5、nches. 2. Metric equivalents are given for information only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Special tools shall be required for assembly. Contact manufacturer. FIGURE 1. General configuration . Provided by IHSNot for ResaleNo reproduction or network
6、ing permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10022 REV PAGE 4 ENGINEERING DATA Nominal impedance: 50 ohms Frequency range: DC to 100 GHz. RF leakage: -80 dB mated pair typical. Voltage rating: 168 V rms maximum at s
7、ea level: 33 V rms at 70,000 feet. Operating temperature: -65C to +165C. REQUIREMENTS (after assembly): (Requirements of drawing 84148 are applicable). Dimensions and configuration: See figures 1. Mating connector in accordance with 10021. Mating interface: In accordance with MIL-STD-348A. Force to
8、engage: 4 pounds, maximum Force to disengage: 2 pounds, minimum Center contact inspection conditions (after heat treat) Oversize test pin: Test pin diameter: .0105 inch +.0001/-.0000 inch. Insertion depth: .010 inch minimum, .070 inch maximum. Number of insertions: 5. Insertion force test: Test pin
9、diameter: .0100 inch +.0001/-.0000 inch. Insertion force: 10 ounces, maximum. Insertion depth: .015 inch minimum, .025 inch maximum. Withdrawal force test: Test pin diameter: .0080 +0000/-.0001 inch. Withdrawal force: 0.25 ounce, minimum. Insertion depth: .015 inch minimum, .025 inch maximum. Radial
10、 misalignment: Not applicable. Axial misalignment: Not applicable. Coupling proof torque: Not applicable. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY
11、CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10022 REV PAGE 5 Center contact retention: .75 pounds minimum axial force (captivated contact). Radial torque: Not applicable. Voltage standing wave ratio: DC to 40 gigahertz: 1.20:1 maximum. 40 to 65 gigahertz: 1.30:1 maximum.
12、VSWR procedure. The VSWR shall be measured in accordance with the following procedure or a method acceptable to the Government. Part should be tested using a Network Analyzer with the Time Domain (TDR) option installed. The recommended network analyzer systems include Hewlett Packard HP 8510. Wiltro
13、n 360 or equivalent. The printer/plotter and the computer should be any unit compatible to the system. Calibration of the system should be performed using the manufacturers calibration kits and the recommended calibration procedures. The frequency range shall be DC to 40 GHz. The VSWR calibration te
14、st setup shall be verified using the manufacturers verification kits. The calibrated system VSWR shall be less than 1.02 + .001F (F in GHZ). The device under test (DUT) shall be attached to the appropriate cable. An adapter capable of performing to 40 GHz such shall be attached to the calibrated tes
15、t port of the analyzer. The DUT shall be mated to the test adapter. The VSWR of the DUT shall be measured using the procedures described in the manufacturers operating instructions. The time domain shall be used to remove the effects of the test adapter. The output shall be generated using the appro
16、priate printer/plotter. Moisture resistance: MIL-STD-202, method 106, except step 7b shall be omitted. Resistance shall be 1,000 megohms within 5 minutes after removal from humidity. Contact resistance (in milliohms, maximum): Initial Center contact 6.0 Outer contact 2.0 Outer conductor to connector
17、 body 0.5 Dielectric withstanding voltage at sea level: 250 V rms minimum. 50 V rms at 70,000 feet. Vibration, high frequency: MIL-STD-202, method 204, test condition D. Vibration, random: MIL-STD-202, method 214, test condition F duration 15 minutes, minimum. Corona level: Altitude: 70,000 feet. 10
18、0 V rms, minimum. Insulation resistance: 3,500 megohms minimum when tested in accordance with MIL-PRF-39012. Altitude: Sea level to 70,000 feet. Solderability (when applicable): Applicable. Shock (specified pulse): MIL-STD-202, method 213, test condition I. Provided by IHSNot for ResaleNo reproducti
19、on or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10022 REV PAGE 6 Thermal shock: MIL-STD-202, method 107, test condition B (except high temperature to be +165C or maximum high temperature of cable). RF high
20、 potential withstanding voltage: 150 V rms minimum at sea level. Frequency: 5 MHz. Leakage current: Not applicable. Cable retention: 20 pounds minimum: torque, not applicable Coupling mechanism retention force: Not applicable. Durability: 100 cycles. RF insertion loss: 0.12 Frequency (GHz) dB Part o
21、r Identifying Number (PIN): 10022 (See figure 1). DSCC drawing PIN 1/ Vendor CAGE number 10022 M17/151-00001 : .047 inch 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Materials: Contacts and adapter housing: Beryllium copper in accordance
22、with ASTM B196/B196M, gold plated to a minimum thickness of 50 microinches (1.27 m) in accordance with MIL-DTL-45204, type II, grade C, class 1, over 50 microinches (1.27 m) minimum of nickel in accordance with MIL-DTL-38999, class 1. Approved sources. Approved sources of supply will be listed herei
23、n. Approved sources are required to be a QPL source on MIL-PRF-39012 or MIL-PRF-31031. Additional sources will be added as they become available. The vendors listed on the requirements drawing agree to this drawing and a certificate of compliance has been submitted to DLA Land and Maritime - VAI. Vendor CAGE Vendor Name and Number address 95077 SV Microwave, Inc. 2400 Centrepark West Drive West Palm Beach, Florida 33409-6469 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
