1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Dimension change (maximum length) in figure 2. Editorial changes throughout. 25 JUL 2013 M. Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV A A A A A A A PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Andrew R. Ernst DESIGN ACTIVITY: DLA
2、LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Original date of drawing 18 December 2012 CHECKED BY Andrew R. Ernst TITLE RESISTOR NETWORK, 8 PIN, DUAL-IN-LINE PACKAGE (DIP), MULTI RESISTANCE VALUES APPROVED BY Michael Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 13003 REV A PAGE 1 OF 7 AMSC N/A 5905-2
3、013-E55 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13003 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for an 8 pin, resistor network with multi
4、resistance values. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 13003 - Y A001 A A I I I I I I I I I I Drawing number Characteristic (1.2.1) Resistance designator Tolerance (1.2.3 and Destructive physical analysis (DPA) testing (1.2.2 and 3.4.6) 3.4.1) (if required) (1.2.4)
5、1.2.1 Characteristics. The characteristic is identified by a single letter and is in accordance with MIL-PRF-83401. 1.2.2 Resistance value. The resistance values are in accordance with MIL-PRF-83401. 1.2.2.1 Resistance value designations. The resistance value designations are as specified in table I
6、. TABLE I. Standard resistance values. 1/ Resistance designator R1(ohms) R2(ohms) R3(ohms) R4(ohms) A001 A002 A003 A004 A005 A006 A007 A008 100K 100K 50K 25K 20K 10K 10K 10K 2K 1K 1K 1K 1K 1K 2K 5K 2K 1K 1K 1K 1K 1K 2K 5K 100K 100K 50K 25K 20K 10K 10K 10K 1/ Contact DLA Land and Maritime-VAT (see 6.
7、6) for additional resistance designator values. Four different resistance values can be supplied. 1.2.3 Resistance tolerance. For available resistance tolerances and designators, see 3.4.1. 1.2.4 DPA testing. The PIN is identified with a single letter “A” if DPA testing is a requirement of group A i
8、nspection, (see 4.2.1) and left blank if it is not a requirement. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4 or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended
9、for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3, 4 or 5 of this specification, whether or not they are listed. 2.2 Government do
10、cuments. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. Provided by IHSNot f
11、or ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13003 REV A PAGE 3 DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capa
12、citor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1580 - Destructive Physical Analysis for Electronic, Electromagnetic, and Electromechanical Parts. * (Copies of these documents are available online at http:/quicksearch.dla.mil or from the DLA Documen
13、t Services, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in t
14、his document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Schematics. The schematic of the resistor ne
15、twork is in accordance with figure 1. The resistor element R1 is the reference resistor element used in determining the ratio accuracy (when applicable). 3.3 Interface and physical dimensions. Resistors shall meet the interface and physical dimensions as specified in herein (see figure 2). FIGURE 1.
16、 Resistor schematics. 3.4 Electrical characteristics. 3.4.1 Resistance tolerance. Resistors are available in A (0.05 percent), B (0.1 percent), D (0.5 percent), F (1 percent), G (2 percent), and J (5 percent) tolerances. Provided by IHSNot for ResaleNo reproduction or networking permitted without li
17、cense from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13003 REV A PAGE 4 Inches .003 .004 .010 .012 .018 .020 mm 0.08 0.10 0.25 0.30 0.46 0.51 Inches .030 .032 .035 .040 .065 .070 mm 0.76 0.81 0.89 1.02 1.65 1.78 Inches .080 .085 .09 .11 .120 .200 mm 2.03 2.16 2
18、.3 2.8 3.05 5.08 Inches .270 .300 .310 .350 .530 mm 6.86 7.62 7.87 8.89 13.46 NOTES: 1. Dimensions are given in inches. 2. Metric equivalents are given for general information only. 3. Pin 1 locator shall be a dot, or a notch in the shaded area. 4. Side brazed configuration optional. * FIGURE 2. Res
19、istor network. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13003 REV A PAGE 5 3.4.2 Power rating. The power rating per schematic “A” shall be as follows: Schematic A Charact
20、eristics C, R, V, and Y Characteristics H, K, and M Element power rating (watts) 0.1 0.2 Network power rating (watts) 0.4 0.8 3.4.3 Temperature range. The operating temperature range shall be -55C to +125C. 3.4.4 Resistance temperature characteristic. The resistance temperature characteristic shall
21、be in accordance with MIL-PRF-83401. 3.4.5 TC tracking. The TC tracking shall be 5 ppm/C. 3.4.6 Resistance. The resistance values shall be 100 ohms to 1 megohm. 3.4.7 Operating voltage. The maximum operating voltage shall be 50 V dc for schematic A. 3.4.8 Destructive physical analysis (DPA). When ex
22、amined as specified in 4.2.4, resistors shall meet the requirements in MIL-STD-1580. 3.5 Marking. Resistors shall be marked with the PIN assigned herein (see 1.2) and manufacturers identification code (CAGE or logo). Pin 1 indicator shall be located adjacent to pin 1. 3.6 Pure tin. The use of pure t
23、in, as an underplate or final finish, is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.7 Recycled, recovered, or environmentally preferable mat
24、erials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the materials meet or exceed the operational and maintenance requirements, and promote economically advantageous life cycle costs. 3.8 Manufacturer eligibility. To be elig
25、ible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-83401 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VAT. 3.8.1 Certif
26、icate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply. 3.9 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and free from defects that will affect life, serviceability, or ap
27、pearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection in accordance with MIL-PRF-83401 is not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A (M level part) and g
28、roup B inspections of MIL-PRF-83401. When DPA is a requirement of group A inspection a minimum of 3 pieces or 1% of the lot whichever is less but not to exceed 5 pieces sample with 0 defects allowed. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of complian
29、ce with group B requirements in lieu of performing group B tests (see 6.2c). 4.2.3 Power conditioning. The power conditioning shall be performed at rated power. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE
30、 A CODE IDENT NO. 037Z3 DWG NO. 13003 REV A PAGE 6 4.2.4 Destructive physical analysis (see 3.4.8). Resistors shall be examined as specified in MIL-STD-1580. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). Whe
31、n packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military S
32、ervice or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains
33、information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Resistor networks are intended to be used in electronic circuit where miniaturization is required. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete
34、 PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group B tests or provides certification of
35、compliance with group B requirements (see 4.2.2). d. Requirements for packaging and packing. 6.3 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena
36、 when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 that specifies a preventive packaging procedure. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufactu
37、re. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, b
38、y mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since
39、they have not been qualified nor tested for such applications, damage and premature failure are possible. These resistors only see a onetime pulse (Short-time overload) as part of the group B inspection of MIL-PRF-83401. 6.6 User of record. Coordination of this document for future revisions is coord
40、inated only with the approved source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614)
41、692-0552 or DSN 850-0552. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13003 REV A PAGE 7 6.7 Approved source of supply. Approved source of supply is listed herein. Additiona
42、l sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DLA Land and Maritime Drawing PIN 1300
43、3-*A Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address characteristics: Y,C, R, V res. values: 100 ohms to 1 megohms all tolerances with or without DPA testing HD112-151UF 57489 Vishay Thin Film 2160 Liberty Drive Niagara Falls, NY 14304 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
