1、REVISIONS LTR DESCRIPTION DATE APPROVED B Part number update. Added vendor CAGEs 60563 and 28198; deleted vendor CAGEs 25330 and 71785. 90-07-31 R Marbias C Changes in accordance with NOR 5935-R018-92. For CAGE 28198, add additional DESC part numbers and corresponding vendor part numbers. 92-05-08 J
2、ames P. Donohue D Correct part numbers on page 5. Change “part number” to “Part or Identifying Number (PIN)”. Editorial changes throughout. 93-10-27 James P. Donohue E Vendor CAGE 60563, PINs, delete and substitute new PINs. Editorial changes throughout. 01-01-22 Robert M. Heber F Add Vendor CAGE SW
3、884, delete MIL-STD-1344 test methods, add EIA-364 test procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV F E E F F F REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC G Dennis L. Kelly DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY
4、 TITLE L. V. Olszewski APPROVED BY Richard Marbais CONNECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, TEN SIZE 20 SIGNAL CONTACTS, WITH ONE SIZE 8 CONTACT CAVITY SIZE CAGE CODE 037Z3 DWG. NO.85041 Original date of drawing 8 May 1986 A REV F PAGE 1 OF 6 AMSC N/A 5935-E762-000 Provided by IHSNot fo
5、r ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm .056 .112 .164 .218 .273 .327 .382 1.42 2.84 4.17 5.54 6.93 8.31 9.70 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless
6、otherwise specified, tolerance for three place decimals is .005 inch (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a .005 inch (0.13 mm) diameter circle. 6. Markings are shown for the pin insert front. Socket inserts are the opposite. 7
7、. Reference documents shall be of the issue in effect on date of invitations for bid. FIGURE 1. Insert arrangement-ten size 20 signal contacts with one size 8 contact cavity. 037Z3 85041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE2 Provided by IHSNot for ResaleNo reproduction
8、 or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C to +125C. REQUIREMENTS: Requirements of drawing 85039 and MIL-DTL-24308 are applicable. Dimensions and configurations: See figure 1.
9、Signal contact specification: Style A (crimp removable signal contacts): Socket: M39029/63-368. Pin: M39029/64-369. Style B (solder fixed signal contacts): Socket: MIL-DTL-24308 Appendix B, figure B-1. Pin: MIL-DTL-24308 Appendix B, figure B-2. Shell size: Two. Shell specification: Style A: Socket:
10、MIL-DTL-24308/2, figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be designated for contact insertion and removal with the applicable military tool as follows: Contact si
11、ze Tool PIN20 M81969/39 - 01 with plastic tip M81969/1-02 with metal tip 037Z3 85041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Mating and unmating force
12、s (with signal contacts only installed): See table I. TABLE I. Mating and unmating forces. Mating force (pounds) Unmating force (pounds) Contact type Minimum Maximum Minimum Maximum Signal 0.385 6.54 0.385 3.8 Contact resistance: See table II. TABLE II. Contact resistance (millivolts maximum). 1/ Co
13、ntact classes G, D, M, N Contact Size AWG wire Size Test current (amperes) After salt spray All others 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstanding voltage: See table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condition
14、 All other conditions Sea level 600 1,000 70,000 - 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature shall be -55C to +125C. 037Z3 85041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVF P
15、AGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this dr
16、awing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE SW884 6/ 85041GAEP 6/ 85041GAES 6/ 85041GBEP 6/ 85041GBES 85041DAEPT 85041DAEST 85041DAEPR 85041DAESR CBC11W1M1F000-50-799.2 CBC11W1F1F000-50
17、-799.2 CBC11W1M10000-50-799.0 CBC11W1F10000-50-799.0 85041GAEPT 85041GAEST 85041GAEPR 85041GAESR CBC11W1M1F00C-50 CBC11W1F1F00C-50 CBC11W1M1F00C-50 CBC11W1F1F00C-50 85041GBEPT 85041GBEST 85041GBEPR 85041GBESR DAMMY11W1PA101 DAMMY11W1SA101 DAMM11W1PA101 DAMM11W1SA101 P111PSA2D P111RSA2D P111PSA2 P111
18、RSA2 CBM11W1M02F00C-0 CBM11W1F02F00C-0 CBM11W1M02000C-0 CBM11W1F02000C-0 PAMMHW11W1P PAMMHW11W1S PAMMW11W1P PAMMW11W1S 85041NAEPT 85041NAEST 85041NAEPR 85041NAESR CBC11W1M1F00C-50-403.0 CBC11W1F1F00C-50-403.0 CBC11W1M1000C-50-403.0 CBC11W1F1000C-50-403.0 85041MAEPT 85041MAEST 85041MAEPR 85041MAESR C
19、BC11W1M1F000-50-403.4 CBC11W1F1F000-50-403.4 CBC11W1M10000-50-403.3 CBC11W1F10000-50-403.3 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall include a full
20、complement of signal contacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap-in and removable. 5/ For size 8 contacts, see DSCC drawings 89046 through 89061. 6/ Pins 85041GAEP, 85041GAES, 85041GBEP, and 850410GBES are canceled and superseded by 85041GAEPT, 85041GAEST,
21、85041GBEPT, and 85041GBEST respectively. 037Z3 85041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVF PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Vender CAGE Vendor name number and address 28198 Positron
22、ics Industries, Incorporated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 85041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVF PAGE6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
