1、REVISIONS LTR DESCRIPTION DATE APPROVED B Part number update. Added vendor CAGEs 60563, 28198; and 00779: deleted vendor CAGEs 25330 and 71785. 90-07-31 R Marbias C Vendor CAGE 60563, PINs, delete and substitute new PINs. Editor changes throughout. 01-01-22 Robert M. Heber D Add Vendor CAGE SW884, d
2、elete MIL-STD-1344 test methods, add EIA-364 test procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV D C C D D REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Dennis L. Kelly DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE L.
3、V. Olszewski APPROVED BY Richard Marbais CONNECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, SEVENTEEN SIZE 20 SIGNAL CONTACTS, WITH SEVEN SIZE 8 CONTACT CAVITIES SIZE CAGE CODE 037Z3 DWG. NO.85054 Original date of drawing 8 May 1986 A REV D PAGE 1 OF 5 AMSC N/A 5935-E768-000 Provided by IHSNot fo
4、r ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm Inches mm .056 .109 .112 .218 .270 .326 1.42 2.77 2.84 5.54 6.86 8.28 .435 .540 .544 .652 .761 .810 .870 11.05 13.72 13.82 16.56 19.33 20.57 22.10 NOTES: 1. Dimensions ar
5、e in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance for three place decimals is .005 inch (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a .005 inch (0.13 mm) diameter circl
6、e. 6. Markings are shown for the pin insert front. Socket inserts are the opposite. 7. Reference documents shall be of the issue in effect on date of invitations for bid. FIGURE 1. Insert arrangement, seventeen size 20 signal contacts, with seven size 8 contact cavities. 037Z3 85054 DEFENSE SUPPLY C
7、ENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVC PAGE2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C to +125C. REQUIREMENTS: Requirements
8、 of drawing 85039 and MIL-DTL-24308 are applicable. Dimensions and configurations: See figure 1. Signal contact specifications: Style A: (crimp removable signal contacts) Socket: M39029/63-368. Pin: M39029/64-369. Style B: (solder fixed signal contacts) Socket: MIL-DTL-24308 Appendix B, figure B-1.
9、Pin: MIL-DTL-24308 Appendix B, figure B-2. Shell size: Five. Shell specifications: Style A: Socket: MIL-DTL-24308/2, figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be d
10、esigned for contact insertion and removal with the applicable military tools as follows: Contact size Tool PIN 20 M81969/39-01 with plastic tip M81969/1-02 with metal tip Mating and unmating forces (with signal contacts only installed): See table I. TABLE I. Mating and unmating forces. Mating force
11、(pounds) Unmating force (pounds) Contact type Minimum Maximum Minimum Maximum Signal 0.655 11.10 0.655 6.5 037Z3 85054 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVC PAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE
12、 DWG NO. Contact resistance: See table II. TABLE II. Contact resistance (millivolts maximum). 1/ Contact classes G, D, M, N Contact Size AWG wire Size Test current (amperes) After salt Spray All others 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstand
13、ing voltage: See table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condition All other conditions Sea level 600 1,000 70,000 - 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature s
14、hall be -55C to +125C. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawin
15、g PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE 00779 CAGE SW884 6/ 85054GBEP 6/ 85054GBES 85054GBEPT 85054GBEST 85054GBEPR 85054GBESR DCMMY24W7PA101 DCMMY24W7SA101 DCMM24W7PA101 DCMM24W7SA101 P247PSA2D P247RSA2D P247PSA2 P247RSA2 CBM24W7M02F00C-0 CBM24W7F02F00C-0 CBM24W7M02000C-0 CBM24W7F02
16、000C-0 208743-5 445000-3 PDMMHW24A7P PDMMHW24A7S PDMMW24A7P PDMMW24A7P 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall include a full compliment of signal
17、 contacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap-in and removable. 5 For size 8 contacts, see DSCC drawings 89046 through 89061. 6/ Pins 85054GBEP and 85054GBES are cancelled and superseded by 85054GBEPTand 85054GBEST respectively. 037Z3 85054 DEFENSE SUPPLY CE
18、NTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Vender CAGE Vendor name number and address 00779 Amp, Incorporated 470 Friendship Road Harrisburg, PA 17111-1203 28198 Positron
19、ics Industries, Incorporated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 85054 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
