1、REVISIONS LTR DESCRIPTION DATE APPROVED A 09/02/88 R. Marbais B Change CAGE 14933 to 037Z3. Update references, added wrappost wrappable length, and geometry details. 05/14/02 Robert Heber Prepared in accordance with ASME Y14.100 REV PAGE REV B B B B B B REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED
2、BY PMIC Gail Willis DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Richard Marbais CONNECTORS, ELECTRICAL, UNSHROUDED HEADERS, PWB TERMINATION, .040 SQUARE PIN SIZE CAGE CODE 037Z3 DWG. NO. 86059 Original date of drawing 20 January 1987 A RE
3、V A PAGE 1 OF 6 AMSC N/A 5935-E691 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86059 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-
4、5000 A REV B PAGE 2 Inches mm .010 .040 .060 .189 .200 .240 3.000 0.25 1.02 1.52 4.80 5.08 6.10 76.20 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Headers are stackable, supplied in sixteen position rows. FIGURE 1. Dimensions and configuration.
5、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86059 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 3 REQUIREMENTS: Shall meet the requirements of drawing 86100, except as specified herein. Design
6、and construction: See figure 1. Temperature range: -40C to +105C. Dielectric withstanding voltage: 1,500 volts rms (sea level). Current rating: 6 amperes maximum. Materials: Insulator: The insulator shall be glass-or mineral-filled nylon in accordance with ASTM D4066, glass filled thermoplastic in a
7、ccordance with MIL-M-24519. All plastic material shall be rated V-O in accordance with UL-94. Contacts: Three fourth hard phosphor bronze in accordance with ASTM B139. Contact plating: Contact plating shall be gold in accordance with ASTM B488, class 0.75 (30 microinches) over 50 microinches (1.25 m
8、) minimum nickel in accordance with SAE AMS-QQ-N-290, class 2. Tin-lead plating shall be in accordance with DSCC drawing 86100. Contact finishes: See table I. TABLE I. Contact finishes. A Gold S Tin-lead Solderless wrappost geometry: The solderless wrappost geometry shall be in accordance with figur
9、es 2 and 3. Tip configuration: The tip of the wrappost shall terminate in a radius or bevel to facilitate insertion into the wrapping tool. If the tip of the wrappost terminates in a bevel, the apex of the bevel shall be flat, with no side of the flat exceeding: a. Square: .025 inch (0.63 mm)pin, .0
10、15 inch (0.38 mm) maximum. .045 inch (1.14 mm) pin, .020 inch (0.51 mm) maximum. b. Rectangular: .06 inch x .03 inch (1.52 mm x 0.76 mm) maximum. Torque: The wrappost shall withstand a torque of 2.0 ozf inch (14.12 mN m) without permanent rotation or twisting relative to the mounting surface. Parall
11、elism: See figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86059 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 4 Number of wrapped connections E length Wire gage 30 (mm) Wire gage 28 (mm)
12、Wire gage 26 (mm) Wire gage 24 (mm) Wire gage 22 (mm) Wire gage 20 (mm) Wire gage 18 (mm) 1 .185 (4.70) .219 (5.56) .226 (5.74) .258 (6.55) .303 (7.69) .327 (8.31) .391 (9.93) 2 .320 (8.13) .388 (9.85) .402 (10.21) .466 (11.83) .556 (14.12) .604 (15.34) .732 (18.59) 3 .455 (11.56) .557 (14.15) .578
13、(14.68) .674 (14.43) .809 (20.55) .881 (.22.37) 1.073 (27.25) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 2. Wrappable length (typical connection). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
14、HS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86059 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 5 Housing: Glass filled thermoplastic in accordance with MIL-M-24519, flame retardant. Insulation resistance: 10,000 megohms minimum. Retention force to body: 15 newtons minimum in one dire
15、ction. Printed wiring board (PWB) thickness: .062 inch (1.57 mm). PWB hole size: .063 .004 inch (1.57 0.10 mm). Interface: See drawings 86039 and 86112. Inches mm .0012 .0015 .003 0.030 0.038 0.076 A (mm) B (mm) C (mm) Parallelism (mm) Straightness Inch/inch (mm) .040 (1.02) nominal .037 (0.94) min
16、.040 (1.02) nominal .037 (0.94) min .059 (1.50) max .055 (1.40) min .005 (0.13) .005 (0.13) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 3. Wrappost geometry. .BURR .0015 MAX.003 R MAXBCC.0012 MAXIMUM PERMISSIBLEDIVIATION FROM SQUARE ORRECT
17、ANGLEAProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86059 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 6 Marking: The Part or Identifying Number (PIN) shall be marked on the housing and package i
18、n accordance with MIL-STD-1285. If size, surface condition, or other design considerations dont allow for full marking on the part, marking on the package is only required. The PIN shall include the complete DSCC PIN, manufacturers name or CAGE code, and date code. The marking shall be permanent and
19、 legible in accordance with method 215 of MIL-STD-202. The PIN shall be constructed using the following format: TABLE II. Dash numbers and dimensions. Dash no. Dim. A 010 (mm) Dim. B .010 (mm) Dim. C (mm) 01 02 03 04 .266 (6.76) .266 (6.76) .266 (6.76) .266 (6.76) .120 (3.05) .433 (11.00) .713 (18.4
20、1) .992 (25.20) .596 (15.14) .909 (23.09) 1.189 (30.20) 1.468 (37.29) Approved source of supply: An approved source of supply is listed herein. Additional sources will be added as they become available. The vendor listed on the requirements drawing has agreed to this drawing and a certificate of com
21、pliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ 86059-X01 86059-X02 86059-X03 86059-X04 8N187 8N187 8N187 8N187 75875X01-16-MIL 75875X02-16-MIL 75875X03-16-MIL 75875X04-16-MIL 1/ Parts must be purchased to this DSCC PIN to assure that all performance
22、 requirements and tests are meet. Vendor CAGE Vendor name number and address 8N187 T.T.I 4033 E. Bellknap Street Fort Worth, TX 76111-6600 86059- DSCC drawing number X Plating (See table I) XX Pin length (See table II and figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-