1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add source 06090. 28 Feb 91 Richard Marbais B Add dimension “Z”. Editorial changes throughout. 22 Sept 93 Randy Larson C Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.1
2、00 REV PAGE REV C C C C C C REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC N/A Jeffery Tunstall DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Abdo Abdouni APPROVED BY Robert Heber CONNECTOR ACCESSORIES, ELECTRICAL, ADAPTER, SHRINK BOOT, RFI / EMI, 45 , CATEGORY 3C
3、 FOR MIL-DTL-83723 series III, MIL-DTL-5015 (SAE-AS3400 AND MS3450), SAE-AS81703 SERIES III, AND MIL-C-26482 SERIES II SIZE CAGE CODE 037Z3 DWG. NO. 89017 Original date of drawing 25 Sept 89 A REV C PAGE 1 OF 6 AMSC N/A 5935-E659 DISTRIBUTION STATEMENT A. Approved for public release; distribution i
4、s unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89017 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 2 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproductio
5、n or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89017 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 3 For connector shell size (ref) Dash number SAE-AS81703 series III MIL-C-26482 series II and MIL-DTL-83723 series III MIL-DTL-5015 crimp A m
6、ax dia E max F max Max cable accommodation range -03 3 - - .669 (16.99) .750 (19.05) 1.710 (43.43) 01 -08 - 8 8s .617 (15.67) .750 (19.05) 1.710 (43.43) 01 -10 - 10 10S 10SL .734 (18.64) .770 (19.56) 1.770 (44.96) 03 -12 7 12 12S 12 .858 (21.79) .800 (20.32) 1.830 (46.48) 05 -14 12 14 14S 14 .984 (2
7、4.99) .820 (20.83) 1.920 (48.79) 06 -16 19 16 16s 16 1.112 (28.24) .840 (21.34) 2.030 (51.56) 08 -18 27 18 18 1.218 (30.94) .926 (23.52) 2.220 (56.83) 09 -20 37 20 20 1.345 (34.16) .926 (23.52) 2.220 (56.83) 11 -22 - 22 22 1.468 (37.29) 1.020 (25.91) 2.370 (60.20) 13 -24 - 24 24 1.593 (40.46) 1.020
8、25.91) 2.370 (60.20) 14 -28 - - 28 1.969 (50.01) 1.145 (29.08) 2.420 (61.40) 16 -32 - - 32 2.219 (56.36) 1.207 (30.66) 2.520 (64.01) 18 -36 - - 36 2.469 (62.71) 1.238 (31.44) 2.610 (66.29) 19 -40 - - 40 2.719 (69.06) 2.031 (51.59) 2.750 (69.85) 21 -44 - - 44 2.969 (74.41) 2.031 (51.59) 2.880 (73.15
9、) 23 -48 - - 48 3.219 (81.76) 2.031 (51.59) 3.000 (76.20) 25 -61 61 - - 1.653 (41.99) 1.063 (27.00) 2.450 (62.23) 14 FIGURE 1. Dimensions and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89017
10、DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 4 Z dia Z dia Cable accommodation range W dia + .020 (0.51) Min Max Cable accommodation range W dia + .020 (0.51) Min Max 01 .250 (6.35) .425 (10.80) .560 (14.22) 14 1.125 (28.58) 1.300 (33.02) 1.470 (37.34) 02 .312 (7.92) .487 (12
11、37) .630 (16.00) 15 1.250 (31.75) 1.425 (36.20) 1.600 (40.64) 03 .375 (9.53) .550 (13.97) .690 (17.53) 16 1.375 (34.93) 1.550 (39.37) 1.710 (43.43) 04 .438 (11.13) .613 (15.57) .750 (19.05) 17 1.500 (38.10) 1.675 (42.55) 1.840 (46.74) 05 .500 (12.70) .675 (17.15) .820 (20.83) 18 1.625 (41.28) 1.800
12、 (45.72) 2.000 (50.80) 06 .562 (14.27) .737 (18.72) .890 (22.61) 19 1.750 (44.45) 1.925 (48.90) 2.120 (53.85) 07 .625 (15.88) .800 (20.32) .950 (24.13) 20 1.875 (47.63) 2.050 (52.07) 2.270 (57.65) 08 .688 (17.48) .863 (21.92) 1.020 (25.91) 21 2.000 (50.80) 2.175 (55.25) 2.440 (61.98) 09 .750 (19.05)
13、 .925 (23.50) 1.120 (28.45) 22 2.125 (53.98) 2.300 (58.42) 2.600 (66.04) 10 .812 (20.62) .987 (25.07) 1.200 (30.48) 23 2.250 (57.15) 2.425 (61.60) 2.750 (69.85) 11 .875 (22.23) 1.050 (26.67) 1.270 (32.26) 24 2.375 (60.33) 2.550 (64.77) 2.900 (73.66) 12 .938 (23.83) 1.090 (27.69) 1.260 (32.00) 25 2.5
14、00 (63.50) 2.675 (67.95) 3.06 (77.72) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Metric equivalents are in parentheses. 4. Dimensions apply after plating. 5. Shield termination method optional. Provided by IHSNot for ResaleNo reproduction or networking per
15、mitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89017 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 5 FIGURE 1. Dimensions and configuration Continued. REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 3c. Design and construction: See figure 1. I
16、nterface dimensions shall conform to MS3155. Pull test: With backshell suitably clamped, the braid shall withstand a tensile load of 150 pounds without movement of the braid or clamping device. Electrical resistance: When measured with a 4-terminal bridge at room temperature, the resistance will not
17、 exceed 1 milliohm. The measurement being taken shall be from a point on the braid within 1 inch of the adapter and a point the body of the adapter. Thermal aging: After being subjected to a temperature of 150C for 168 hours, the electrical resistance, measured as above, will not exceed 1 milliohm.
18、Material and finish: Accessory components shall be as shown in table I. TABLE I. Material and finish. Components Material Finish All metal parts Aluminum alloy in accordance with MIL-C-85049 See MIL-C-85049 N, W 1/ Braided shield Copper Tin 1/ N is electroless nickel in accordance with MIL-C-85049 (
19、for space application only). Part or Identifying Number (PIN): The PIN shall be in accordance with the following: 89017- 12 W 14- 06 Drawing number Dash number Finish Cable Length accommodation (1 inch increments, range minimum 6 inches) Marking: Marking shall be in accordance with MIL-C-85049 excep
20、t the PIN shall be stated above. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89017 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 6 Application: Use to adapt SAE-AS31091 and SAE-AS31171 type shri
21、nk boots. QUALIFICATION Qualification inspection: Qualification inspection for the backshells specified herein shall not be required. Quality conformance inspection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-C-85049. Method of inspection: Metho
22、d of inspection shall be in accordance with MIL-C-85049. Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed herein have agreed to this drawing and a certificated of compliance has been submitted to D
23、SCC-VAI. CAGE codes DSCC drawing PIN 1/ 06324 07418 31461 06090 OBW78 89017-xxxxx-xx 319AB001 S1735-xxxxA-xx-xx E5432Axxxxxxx55 TXR54AX45-xxxA12J JT100-B-XXXXXX 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number a
24、nd address 06090 Tyco/Electronics Corporation 300 Constitution Drive Menlo Park, CA 94025-1164 06324 Glenair, Incorporated 1211 Air Way Glendale, CA 91201-2497 07418 Sunbank Electronics, Incorporated 1740 Commerce Way Paso Robles, CA 93446 31461 Electro Adapter, Incorporated 20640 Nordhoff Street Pr
25、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89017 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 7 Chatsworth, CA 91311 OBW78 J-Tech Incorporated 5403 East La Palma Anaheim, CA 92807 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
