1、REVISIONSLTR DESCRIPTION DATE APPROVEDA PIN and source update. 3 August 2001 Robert HeberPrepared in accordance with MIL-STD-100.REVPAGEREVAAAAAREV STATUSOF PAGES PAGE 12345PREPARED BYPMIC N/ARon GaryDEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OHIO 43216-5000CHECKED BY TITLEC. W. KoellerAPPROVED BYRich
2、ard MarbaisCONNECTOR, ELECTRICAL, RECEPTACLE, RADIOFREQUENCY, SERIES BNC, SOCKET CONTACT,FOR M17/152-00001 CABLE.SIZE CAGE CODE037Z3DWG. NO. 89035Original date ofdrawing2 November 1989AREV A PAGE 1 OF 5AMSC N/A 5935-E641-12DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimi
3、ted.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89035DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVAPAGE2NOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.3. A po
4、lyolefin sleeve in accordance with MIL-I-23053/5 shall be supplied with each part.4. Dimension .800 is the largest overall diameter of the connector.5. Wrench flats to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10.6. All undimensioned pictorial configurations are fo
5、r reference purposes only.7. Dimension 1.625 max. defines the overall length of the connector when assembled to the cable.8. No special tools shall be required for assembly to cables.9. Assembly of these connectors shall be in accordance with MIL-PRF-39012 category C. The shield terminationshall be
6、accomplished using the M22520/5-01 basic crimp tool with die M22520/5-37, closure B. The centercontact shall be soldered.10. Gasket material shall be Viton A or an equivalent (Viton A is a trade name of E.I. dupont).FIGURE 1. Jamnut mounted series BNC.Inches mm.012 0.30.032 0.81.045 1.14.104 2.64.11
7、4 2.89.240 6.09.500 12.7.620 15.74.630 16.00.796 19.96.800 20.32.843 21.411.625 41.27Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89035DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVAPAGE3NOTES:1. Dimensions a
8、re in inches.2. Metric equivalents are given for general information only.FIGURE 2. Recommended mounting hole.Inches mm.010 0.25.156 3.96.343 8.71.437 11.10.593 15.06NOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.FIGURE 3. Cable strip dimensions.Inches
9、 mm.473.478.505.51011.9812.1412.8212.95Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89035DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVAPAGE4ENGINEERING DATA:Nominal impedance: 50 ohms.Frequency range: 0 to 4
10、 GHz.Voltage rating: 500 volts rms sea level.125 volts rms at 70,000 feet.Operating temperature: -65C to +165C.REQUIREMENTS: (Requirements of DSCC drawing 84148 are applicable).Dimensions and configuration: See figure 1 and MIL-STD-348.Force to engage and disengage:Longitudinal force: 3 pounds maxim
11、um (13.34 Nm).Torque: 2.5 inch-pounds, maximum (.282 Nm).Coupling proof torque: Not applicable.Hermetic seal: Not applicable.Leakage (pressurized connectors): Not applicable.Center contact retention: 6 pounds minimum axial force (26.69 N).Radial torque: Not applicable.Voltage standing wave ratio (VS
12、WR): The VSWR, when measured in accordance with MIL-PRF-39012, over the frequencyrange of 500 MHz to 4 GHz, or approximately 80 percent of the cable cutoff frequency, whichever is lower, shall not exceed1.30:1.Moisture resistance: Method 106, MIL-STD-202, no measurements at high humidity. Insulation
13、 resistance shall be at least 200megohms minimum within 5 minutes after removal from humidity.Contact resistance (in milliohms maximum):AfterInitial environmentalCenter contact: 1.5 1.5Outer contact: .2 N/ACable braid to body .1 N/ADielectric withstanding voltage: 1,500 V rms minimum, in accordance
14、with MIL-STD-202, method 301.Vibration, high frequency: MIL-STD-202, test condition B of method 204.Corona level: 375 V rms at 70,000 feet (21.336 km).Shock (specified pulse): Method 213, test condition G of MIL-STD-202.Random vibraiton: MIL-STD-1344, test condition V, test level F, method 2005.Ther
15、mal shock: MIL-STD-202, test condition C of method 107.RF high potential withstanding voltage: 1,000 V rms, minimum.Frequency: 5 MHz.Leakage current: Not applicable.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89035DEFEN
16、SE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVAPAGE5Cable retention force: 10 pounds, minimum axial pull (44,48 N).Coupling mechanism retention force: Not applicable.RF leakage: 55 dB, minimum tested between 2 to 3 GHz.RF insertion loss: .2 dB, maximum tested at 3 GHz.Cable accommodation: M17
17、/152-00001.Part or Identifying Number (PIN): 89035BBS.NOTE: These connectors are for use in radio frequency applications only.Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as theybecome available. The vendors listed on the requirements dra
18、wing have agreed to this drawing and a certificate ofcompliance has been submitted to DSCC-VAI.DSCC drawingPIN 1/Vendor CAGEnumberVendor referencePIN 89035BBS 00795 1019100A591-0001/ Parts must be purchased to this DSCC PIN to assure that allperformance requirements and tests are met.Vendor CAGE Vendor namenumber and address00795 Delta Electronics416 Cabot StreetBeverly, MA 01915Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
