1、REVISIONS LTR DESCRIPTION DATE APPROVED A Page 2, 1.1, change socket to pin, change right angle to straight. Page 3 3.6.3 change 89054 to 89055. Page 3 Dimensional clarifications. Editorial changes throughout. 18 Nov 92 Randy Larson B Updated to new DSCC drawing format. Remove references to canceled
2、 Military Specifications and add replacement Industry Specifications. 28 Mar 01 Robert Heber C Remove references to canceled Military Specifications and add replacement Industry Specifications. Other updates in accordance with overage review. 23 Apr 08 Abdonasser M. Abdouni D Page 4, figure 1, dimen
3、sional clarification. 4 Feb 13 Abdonasser M. Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV D C C D C C PAGE 1 2 3 4 5 6 PMIC G PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ralph Antonelli, Jr. Original date of drawin
4、g 27 March 1991 CHECKED BY TITLE James P. Donohue CONTACT, ELECTRICAL, CONNECTOR, HIGH VOLTAGE, PIN, SIZE 8, RIGHT ANGLE, SOLDER APPROVED BY Charles W. Koeller SIZE CAGE CODE DWG. NO. 89057 A 037Z3 REV D PAGE 1 OF 6 AMSC N/A 5935-E848-001 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO:
5、 DLA LAND AND MARITME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89057 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing covers the desi
6、gn and performance requirements for a high voltage, pin size 8, right angle, solder, electrical contact. 1.2 Part or Identifying Number (PIN). The complete PIN shall is as follows: 89057 - 001 Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are sp
7、ecified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for addition information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned t
8、hat they must meet all specified requirements documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified here
9、in. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-24308 - Connectors, Electrical, Rectangular, Miniature, Non-environmental, Polarized Shell, Rack and Panel, General Specification for. (Copies o
10、f these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawing
11、s, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEFENSE SUPPLY CENTER COLUMBUS (DSCC) 89055 - Contact, Electrical, Connector, High Voltage, Socket, Size 8, Stra
12、ight, Solder. 89056 - Contact, Electrical, Connector, High Voltage, Pin, Size 8, Right Angle, Solder. (Copies of these documents are available online at http:/www.landandmaritime.dla.mil/programs/milspec/ or from the DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus, OH 43218-3990.) 2.2 Non-
13、Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ASTM INTERNATIONAL ASTM B488 - Electrodeposited Coatings of Gold for Engineering Us
14、es. (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) SAE INTERNATIONAL SAE-AS39029 - Contacts, Electrical Connector, General Specification For. (Copies of these documents are
15、 available online at http:/www.sae.org or from the SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG
16、NO. A 037Z3 89057 REV C PAGE 3 3. REQUIREMENTS 3.1 Design configuration. The design, construction, and physical dimensions shall be as specified in this drawing (see figure 1) and SAE-AS39029. In case of conflict between this drawing and SAE-AS39029, this drawing shall govern. 3.2 Design documentati
17、on. The design documentation shall be in accordance with SAE-AS39029 and be retained by the manufacturer, but be available for review by the contracting activity, DLA Land and Maritme, or contractor upon request. 3.3 Electrical performance characteristics. The electrical performance characteristics
18、are as specified in table I herein, and apply over the entire operating temperature range as specified for type ”A” contacts in SAE-AS39029. TABLE I. Electrical characteristics. Electrical characteristics Value Maximum current 5 amperes Working voltage 500 V rms Maximum voltage 2,000 V rms Contact r
19、esistance (max) 0.01 ohm Insulation resistance 5 gigohms 3.4 Marking. Marking shall be in accordance with SAE-AS39029 except the DLA Land and Maritime drawing PIN shall be used in place of the M39029 PIN. 3.5 Quality assurance requirements. Contacts furnished under this drawing shall have been subje
20、cted to, and passed all the requirements, tests, and inspections detailed herein, including quality conformance inspection. 3.6 Environmental and mechanical performance characteristics. The environmental and mechanical performance characteristics are as specified for type “A” contacts in SAE-AS39029
21、 and this drawing. 3.6.1 Tools. Installation tool is not required. Removal tool shall be M81969/14-06. 3.6.2 Contact plating. Overall contact plating shall be in accordance with ASTM B488, type II, code C, class 1.27. 3.6.3 Mating contact. The contact specified in this drawing shall be capable of ma
22、ting with contacts specified in DLA Land and Maritime drawings 89055 and 89056. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89057 REV D PAGE 4 Inches mm Inches
23、 mm .001 0.03 .188 4.78 .002 0.05 .218 5.54 .040 1.50 .697 17.70 .082 2.08 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three-place decimals and .01 (0.3 mm) for two-place decimals. FIGURE 1
24、. Dimensions for contact power, size 8.-.002 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89057 REV C PAGE 5 3.7 Qualifications. Qualification inspection for co
25、ntacts specified herein shall not be required. 3.7.1 Quality conformance inspection. The quality conformance inspection shall be in accordance with SAE-AS39029 and 4.2 herein. 3.8 Manufacturer eligibility. To be eligible to supply contacts to this drawing, a manufacturer must: a. Agree to make avail
26、able to DLA Land and Maritime upon request, all pertinent test data on its production of the subject part. b. Provide to DLA Land and Maritime-VAI or its designated agent, upon request, free of charge, and without obligation, a current sample from its production of the subject part. c. Meet one of t
27、he following criteria: 1. Currently hold QPL status on MIL-DTL-24308 or SAE-AS39029. 2. Be in current production with subject part. 3.9 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as and approved source (see 3.8 and 6.6). 4. QUAL
28、ITY ASSURANCE PROVISIONS 4.1 Qualification inspection. Qualification inspection for contacts specified in this document are not required. 4.2 Quality conformance inspection. Quality conformance inspection shall utilize sampling and testing methods, which will assure all contacts supplied to this dra
29、wing, will meet the inspection requirements of group B inspection of SAE-AS39029. Conforming test data shall be retained for a minimum of 3 years by the manufacturer, and be available at all times for inspection by appropriate qualification or customer personnel. 5. PACKAGING 5.1 Packaging. For acqu
30、isition purposes, the packaging requirement shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirement
31、s. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Department or Defense Agencys automated packagi
32、ng files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. Contacts conforming to this drawing are intended for use when military specifications do not exist, and qualified military contacts that will perform the required function are not available for
33、 original equipment manufacturers applications. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings and stock catalog listing. 6.2 Acquisition requirements. The acquisition documents should specify the following: a. Complete PIN. b. Req
34、uirements for delivery one copy of the quality conformance inspection (see 4.2) data pertinent to the contact inspection lot, to be supplied with each shipment by the contact manufacturer, if applicable. c. Requirements for certificate of compliance (see 3.9), if applicable. d. Requirements for pack
35、aging and packing (see 5.1). 6.3 Applicable connectors. These contacts can be used in connectors which are referenced in DLA Land and Maritime drawing 85039. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH
36、 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89057 REV C PAGE 6 6.4 Generic test data. Generic test data may be used to satisfy the requirements of 4.2. Generic test data will be on date codes no more than 1 year old, with the same material, design, and manufacturing process. The vendor is required to
37、 retain the generic data for a period of not less than 3 years from the date of shipment. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VAI, Columbus, Ohio 43218-3990, or telephone (614) 692-0530 or by e mail to RectangularConnectordscc.dla.mil. 6.6 Approved sour
38、ces of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed have agreed to the contents of this drawing and a certificate of compliance has been submitted to DLA Land and Maritime-VAI. DSCC drawing PIN Vendor CAGE number
39、Vendor similar PIN 1/ 89056-001 28198 FS4920D-50 60563 15-0520-1001C 1/ Caution. Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE number Vendor name and address 28198 Positronic Industries, Incorporated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
