1、REVISIONS LTR DESCRIPTION DATE APPROVED A Delete “part number” and substitute “Part or Identifying Number (PIN)”. Vendor CAGE 60563, PIN, delete and substitute new PIN. Editorial changes throughout. 01-01-22 Robert M. Heber B Add Vendor CAGE SW884, delete MIL-STD-1344 test methods, add EIA-364 test
2、procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV B A A B B REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ralph Antonelli DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Charles W. Koeller CON
3、NECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, TWELVE SIZE 20 SIGNAL CONTACTS, WITH FIVE SIZE 8 CONTACT CAVITIES SIZE CAGE CODE 037Z3 DWG. NO. 89079 Original date of drawing 31 July 1990 A REV B PAGE 1 OF 5 AMSC N/A 5935-E774-000 Provided by IHSNot for ResaleNo reproduction or networking permitt
4、ed without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm Inches mm .055 .056 .109 .112 .163 .218 1.40 1.42 2.77 2.84 4.14 5.54 .272 .326 .343 .381 .435 .618 .893 6.91 8.28 8.71 9.68 11.05 15.70 22.68 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for
5、information only. 3. Unless otherwise specified, tolerance for three place decimals is .005 (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a 0.005 (0.13 mm) diameter circle. 6. Markings are shown for the pin insert front. Socket inserts
6、are the opposite. 7. Reference documents shall be of the issue in effect on date of invitations for bid. 037Z3 89079 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE2 FIGURE 1. Insert arrangement, twelve size 20 signal contacts, with five size 8 contact cavities.Provided by IHSNot
7、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55to +125C. REQUIREMENTS: (Requirements of drawing 85039 and MIL-DTL-24308 are applicable). Dimensions and conf
8、igurations: See figure 1. Signal contact specifications: Style A: (crimp removable signal contacts) Socket: M39029/63-368. Pin: M39029/64-369. Style B: (solder fixed signal contacts) Socket: MIL-DTL-24308, Appendix B, figure B-1. Pin: MIL-DTL-24308, Appendix B, figure B-2. Shell size: Four. Shell sp
9、ecifications: Style A: Socket: MIL-DTL-24308/2, figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be designed for contact insertion and removal with the applicable militar
10、y tool as follows: Contact size Tool PIN 20 M81969/39-01 with plastic tip M81969/1-02 with metal tip Mating and unmating forces with signal contacts only installed (pounds): See table I. TABLE I. Mating and unmating forces. Mating Unmating Contact type min max min max Signal 0.462 7.8 0.462 4.6 037Z
11、3 89079 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Contact resistance: See table II. TABLE II. Contact resistance (millivolts maximum). 1/ Contact class
12、G, D, M, N Contact size AWG Wire size Test current (amperes) After salt spray All other 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstanding voltage: See table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condition All other cond
13、itions Sea level 70,000 ft 600 - 1,000 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature shall be -55C to +125C. Approved sources of supply are listed herein. Additional sources will be added as they b
14、ecome available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE SW884 89079GBEPT 89079GBEST 89079GBEPR 89079GBESR DCMMY
15、17W5PA101 DCMMY17W5SA101 DCMM17W5PA101 DCMM17W5SA101 P175PSA2D P175RSA2D P175PSA2 P175RSA2 CBM17W5M02F00C-0 CBM17W5F02F00C-0 CBM17W5M02000C-0 CBM17W5F02000C-0 PCMMHW17W5P PCMMHW17W5S PCMMW17W5P PCMMW17W5P 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not
16、satisfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall include a full compliment of signal contacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap in and removable. 5/ For size 8 contacts, see DSCC drawings 89046 and 89061. 0
17、37Z3 89079 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Vendor CAGE Vendor name number and address 28198 Positronics Industries, Incorporated 423 North Cam
18、pbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 89079 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
