1、NOTICE OF REVISION (NOR) a. (X one) 1. DATE (WMMDD) I X (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Custodian of master document shall make above revision and furnish revised docu
2、ment. 04-05-07 This revision described below has been authorized for the document listed. Public repong burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions, searching existing data SOUTcBs. gathering and maintaining the data needed,
3、and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information. including suggestions for reducing this burden, to Department of Defense, Washington Headquarters SeMces, Directorate for Infonation Operati
4、ons and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 222024302, and to the office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. PLEASE DO NOT RETURN YOUR COMPLETED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMEN
5、T ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT 5. CAGE CODE 03723 b. ADDRESS (Street, City, State, Zip Code) 4. ORIGINATOR Defense Supply Center Columbus 3990 East Broad Street Columbus,
6、 Ohio 43216-5000 c. TYPED NAME (First, Middle Initial. Last) a. TYPED NAME (First, Middle Initial, Last) Jeffery Tunstall 9. TITLE OF DOCUMENT CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, EMIIRFI 90” END ENTRY,CATEGORY 2B, FOR MIL-(2-24308 CONNECTORS d. TITLE CHIEF, INTERCONNECTION D
7、EVICES 15a. ACTIVITY ACCOMPLISHING REVISION DSCC-VAI 7. CAGE CODE 1 03723 e. SIGNATURE Richard L. Taylor b. REVISION COMPLETED (Signature) Jeffery Tunstall io. REVISION LETTER a. CURRENT A b. NEW B - Form Approved 0188 OMB NO. 0704- 2. PROCURING ACTIVITY NO. 3. DODAAC 6. NOR NO. 5935-R028-03 a. DOCU
8、MENT NO. 891 07 ECP NO. 11. NIA ALL 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES 13. DESCRIPTION OF REVISION Page 2, Delete the following paragraphs: “Pull test”, “Electrical resistance” and “Thermal aging”. Page 3, Relocate “A” and “D” leader lines. Page 4, dash number 01, dimension J: D
9、elete l.718” and substitute l.843”. Page 4, dash number 01, dimension K Min: delete “.I25 and substitute “.250”. Page 4, dash number 01, dimension K Max: delete “.250” and substitute I.375”. Richard L. Taylor f. DATE SIGNED (04-05-07) c. DATE SIGNED (04-05-07) Provided by IHSNot for ResaleNo reprodu
10、ction or networking permitted without license from IHS-,-,-LTR DESCRIPTION DATE A Update format. 16 July 02 Correcting references. Correcting address list of sources. Preparei REV APPROVED Robert Heber PAGE REV STATUS DF PAGES REV AAAAA PAGE 12345 PMIC N/A Original date of drawing PREPAREDBY Jefferv
11、 Tunstali 26 July 90 CHECKED BY I hbdo Abdouni APPROVED BY Robert Heber CAGE CODE DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 TITLE CONNECTOR, ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, EMVRFI 90 DEGREES END ENTRY, CATEGORY 2B, FOR MIL-C-24308 CONNECTORS DWG. NO. 891 07 PAGE 1
12、OF 5 4MSC N/A 5935-E666 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 28. Design and construction: See figure 1. Pull test: With backshell suitablyclamped, the braid shall withstand a
13、tensile load of 150 pounds (667 N), with out movement of the braid or clamping device. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 4321 6-5000 Electrical resistance: When measured with a 4-terminal bridge at room temperature, the resistance shall not exceed 1 milliohm. The measurement being taken s
14、hall be from a point on the braids within 1 inch (25.4 mm) of the adapter and a point on the body of the adapter. SIZE A Thermal aging: After being subjected to a temperature of 150C for 168 hours, the electrical resistance, measured as above, shall not exceed 1 milliohm. Materials and finish: Acces
15、sory components: Aluminum alloy shall be in accordance with MIL-C-85049. Jackscrews: CRES shall be in accordance with SAE-AMS-QQ-S-763 passivated. EM1 gasket: Shall be in accordance with 86128. Finish: N or W shall be in accordance with MIL-(2-85049. N is electroless nickel in accordance with MlL-C-
16、85049 (for space applications only). Part or Identifying Number (PIN): The PIN shall be in accordance with the following example: Finish Marking: Marking shall be in accordance with MIL-C-85049, except the PIN shall be as stated above. Qualification inspection: Qualification inspection for the backs
17、hells specified herein shall not be required. Quality conformance inspection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-C-85049. Methods if inspection: Shall be in accordance with MIL-C-85049. CAGE CODE DWG NO. 03723 891 07 Provided by IHSNot f
18、or ResaleNo reproduction or networking permitted without license from IHS-,-,-1.190 i KXZ3) STYLE G GLAND NUT E T - JACKSCREW ,- SHRINK SLEEVE E ENTRY F I I I FIGURE 1. Backshell 90“. end entry. I I REV A PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
19、m IHS-,-,-Dash number o1 02 03 04 05 Shell size 1 2 3 4 5 A 1.363 (34.62) 1.691 (42.95) 2.250 (57.15) 2.879 (73.1 3) 2.785 (70.74) B max .624 (1 5.85) .624 (15.85) .624 (1 5.85) .624 (1 5.85) .735 (1 8.67) C .322 (8.1 8) .322 (8.1 8) .322 (8.1 8) .322 (8.1 8) .375 (9.52) D - + .O05 .984 (24.99) 1.31
20、2 (33.32) 1.852 (47.04) 2.500 (63.50) 2.406 (61.1 1) E .340 (8.64) .340 (8.64) .343 (8.71) .343 (8.71 ) ,343 (8.71) ,“, F 1.750 1 .718 1 .125 1 250 (44.50 (1 8.24) (3.1 8) (6.35) 1.750 1 .843 1 .250 1 .375 (44.50) (21.41) (6.35) (9.52) 2.000 1 .968 1 ,312 1 .475 (50.80) (24.59) (7.92) (12.07) 2.000
21、I .968 1 .312 1 .475 (50.80) (24.59) (7.92) (12.07) 2.000 1 1.109 1 ,437 1 .575 (50.80) (28.82) (1 1 .lo) (14.61) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Metric equivalents are in parenthesis. FIGURE 1. Backshell 90“. end entry - Continued
22、. SIZE DEFENSE SUPPLY CENTER, COLUMBUS I IA COLUMBUS, OH 43216-5000 CAGE CODE 03723 DWG NO. 891 07 4 REV A I PAGE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Approved source of supply. An approved source of supply is listed herein. Additional sou
23、rces will be added as they become available. The vendor listed herein has agreed to this drawing and a certificate of compliance has been to DSCC-VAI. PIN Il 891 07-XXX 1 DSCC drawing I Vendor CAGE number I 06324 550E002 - 1/ Parts must be purchased to this DSCC Pin to assure that all performance re
24、quirements and tests are met. Vendor CAGE number 06324 Vendor name and address Glenair, Incorporated 121 1 Air Way Glendale, CA 91201 CAGE CODE DWG NO. 03723 891 07 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
