1、VISIONS LTR DESCRIPTION DATE APPROVED A Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC N/A Jeffery Tunstall DEFENSE SUPPLY CENTER, CO
2、LUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Abdo Abdouni APPROVED BY Robert Heber CONNECTOR, ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, EMI/RFI 90 DEGREES, SIDE ENTRY, CATEGORY 2B, FOR MIL-DTL-24308 CONNECTORS SIZE CAGE CODE 037Z3 DWG. NO. 89109 Original date of drawing 26 July 90 A RE
3、V PAGE 1 OF 5 AMSC N/A 5935-E668 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89109 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5
4、000 A REV A PAGE 2 REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 2B. Design and construction: Interface dimensions shall be in accordance with MIL-DTL-24308. Pull test: With backshell suitably clamped, the braid shall withstand a tensile load of 150 pounds (667 N), with out movemen
5、t of the braid or clamping device. Electrical resistance: When measured with a 4 terminal bridge at room temperature, the resistance shall not exceed 1 milliohm. The measurement being taken shall be from a point on the braids within 1 inch (25.4 mm) of the adapter and a point on the body of the adap
6、ter. Thermal aging: After being subjected to a temperature of 150C for 168 hours, the electrical resistance, measured as above, shall not exceed 1 milliohm. Materials and finish: Accessory components: Aluminum alloy shall be in accordance with MIL-C-85049. Jackscrews: CRES shall be in accordance wit
7、h SAE-AMS-QQ-S-763 passivated. EMI gasket: Shall be in accordance with drawing 86128. Finish: N or W shall be in accordance with MIL-C-85049. N is electroless nickel in accordance with MIL-C-85049 (for space applications only). Part or Identifying Number (PIN): The PIN shall be in accordance with th
8、e following example: 89109- 01 W Drawing number Dash Finish number Marking: Marking shall be in accordance with MIL-C-85049, except the PIN shall be as stated above. Qualification inspection: Qualification inspection for the backshells specified herein shall not be required. Quality conformance insp
9、ection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-C-85049. Methods if inspection: Shall be in accordance with MIL-C-85049. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO.
10、037Z3 89109 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 3 FIGURE 1. Backshell 90, side entry. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89109 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 432
11、16-5000 A REV A PAGE 4 K Dash number Shell size A B max C D + .005 E + .030 F H max Min Max 01 1 1.363 (34.62) .624 (15.85) .322 (8.18) .984 (24.99) .340 (8.64) 1.625 (41.28) .968 (24.59) .125 (3.18) .250 (6.35) 02 2 1.691 (42.95) .624 (15.85) .322 (8.18) 1.312 (33.32) .340 (8.64) 1.625 (41.28) 1.06
12、2 (26.97) .250 (6.35) .375 (9.52) 03 3 2.250 (57.15) .624 (15.85) .322 (8.18) 1.852 (47.04) .343 (8.71) 1.844 (46.84) 1.156 (29.36) .312 (7.92) .475 (12.07) 04 4 2.879 (73.13) .624 (15.85) .322 (8.18) 2.500 (63.50) .343 (8.71) 1.844 (46.84) 1.156 (29.36) .312 (7.92) .475 (12.07) 05 5 2.785 (70.74) .
13、735 (18.67) .375 (9.52) 2.406 (61.11) .343 (8.71) 1.844 (46.84) 1.218 (30.94) .437 (11.10) .575 (14.61) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Metric equivalents are in parenthesis. Provided by IHSNot for ResaleNo reproduction or networki
14、ng permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89109 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 5 FIGURE 1. Backshell 90, side entry - Continued. Approved source of supply. An approved source of supply is listed herein. Additional sources will be add
15、ed as they become available. The vendor listed herein has agreed to this drawing and a certificate of compliance has been to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number 06324 89109-XXX 550S002 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 06324 Glenair, Incorporated 1211 Air Way Glendale, CA 91201 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
