1、 REVISIONS LT DESCRIPTION DATE APPROVED A Revise section 4; editorial changes throughout. 2 MAR 92 D. MOORE B Changes in accordance with NOR 5905-R019-93. 21 OCT 93 Andrew R. Ernst C New sources of supply; dimensional changes in accordance with MIL-PRF-55342/6; Editorial changes throughout. 5 APR 99
2、 James A. Crum D Change vendor similar type number. Editorial corrections throughout. Update to present DoD policy requirements. 7 Nov 03 Kendall A. Cottongim E Maximum allowed resistance by termination; Addition of termination finishes G, U, T, C, D, and W. 3 May 04 Kendall A. Cottongim F Inactive
3、for new design. Revise to present DoD policy requirements. 12 Apr 05 Kendall A. Cottongim CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Notice of Inactivation for New Design DSCC Drawing 90048 is inactive for new design and
4、 is no longer used, except for replacement purposes. Use MIL-PRF-32159/6 Prepared in accordance with ASME Y14.100 Selected item drawing REV STATUS OF PAGES REV F F E E F E PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY David Wood DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH Original date of
5、drawing 28 August 1990 CHECKED BY David Wood TITLE RESISTOR, CHIP, FIXED, FILM, ZERO-OHM, STYLE 0705 APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 90048 REV F PAGE 1 OF 6 AMSC N/A 5905-E525 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
6、S-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 90048 REV F PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a fixed, film, 0.070 X 0.050, zero-ohm, chip resistor. 1.2 Part or Identifying Number (PIN) The complete PIN is as follows and is
7、 available in termination material as specified in MIL-PRF-55342 and herein (see 3.3.3 however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot co
8、des. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advant
9、ageous life cycle costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.7 Workmanship. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearanc
10、e. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-55342 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Qualification inspection. Qualification inspection is not applicable to this document. 4.3 Product level qu
11、alification. The product level qualification specified in MIL-PRF-55342 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection (established reliability level only and the parts p
12、er million reporting is not applicable) of MIL-PRF-55342. 4.5 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-55342. 5. PACKA
13、GING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain re
14、quisite requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the Military Services System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agen
15、cys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 90048 REV F PAGE 5
16、6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended for use in thick or thin film circuits where microcircuitry is intended. Resistors are also for use in surface mount applications.
17、 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufa
18、cturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online
19、at Resistordla.mil or in writing to: DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.4 Suggested sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the u
20、se of this drawing may be obtained online at Resistordla.mil or contact DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPL
21、Y CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 90048 REV F PAGE 6 DSCC drawing PIN 90048-* Vendor similar Designation or type Number 1/ Vendor CAGE Vendor name and address Terminations B, C, G, U, and W. H0705CPX000(DEC 048) H0705CPC000(DEC 048) H0705CPG000(DEC 048) H0705CPU000(DEC 048) H
22、0705APG000(DEC 048) 56235 State of the Art, Incorporated 2470 Foxhill Road State College, PA 16803-1797 Termination B RCWPM-575-99 91637 Vishay Dale, Incorporated Box 609 Columbus, NE 68602-0609 Plant: Vishay Israel, Ltd Emek-Sara “B” Industrial Park Beer Sheva, Isael 84874 Terminations B, G, U, and
23、 T. WAJ86PS-NS62 WAJ86PS-NUX WAJ86PG-U MSRJ86PG-U WAJ86G-U 50316 Mini-Systems, Incorporated 20 David Road N. Attleboro, MA 02761-0069 Terminations B, G, and W. M0805XR000SB 57489 Vishay Thin Film 2160 Liberty Drive Niagara Falls, NY 14304-3676 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
