DLA DSCC-DWG-90092 REV C-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE RM1505 [Use DLA MIL-PRF-32159 4 (1) DLA MIL-PRF-32159 4]《固定薄膜片状0欧姆RM1505型电阻器[使用 DLA MIL-PRF-32159 4]》.pdf
《DLA DSCC-DWG-90092 REV C-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE RM1505 [Use DLA MIL-PRF-32159 4 (1) DLA MIL-PRF-32159 4]《固定薄膜片状0欧姆RM1505型电阻器[使用 DLA MIL-PRF-32159 4]》.pdf》由会员分享,可在线阅读,更多相关《DLA DSCC-DWG-90092 REV C-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE RM1505 [Use DLA MIL-PRF-32159 4 (1) DLA MIL-PRF-32159 4]《固定薄膜片状0欧姆RM1505型电阻器[使用 DLA MIL-PRF-32159 4]》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 REVISIONS LT DESCRIPTION DATE APPROVED A Correct vendors CAGE number. Editor changes throughout. 9 DEC 98 W. Sindelar B Add vendor. Editor changes throughout. 10 SEP 99 K. Cottongim C Inactive for new design. Revise to present DoD policy requirements. 12 Apr 05 Kendall A. Cottongim CURRENT DESIGN A
2、CTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Notice of Inactivation for New Design DSCC Drawing 90092 is inactive for new design and is no longer used, except for replacement purposes. Use MIL-PRF-32159/4 Prepared in accordance with ASME
3、Y14.100 Selected item drawing REV STATUS OF PAGES REV C C B C C PAGES 1 2 3 4 5 PMIC N/A PREPARED BY David Wood DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH Original date of drawing 17 December 1990 CHECKED BY David Wood TITLE RESISTOR, CHIP, FIXED, FILM, ZERO-OHM, STYLE RM1505 APPROVED BY David E. M
4、oore SIZE A CODE IDENT. NO. 14933 DWG NO. 90092 REV C PAGE 1 OF 5 AMSC N/A 5905-E523 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 90092 REV C PAGE 2 1. SCOPE 1.1 Sco
5、pe. This drawing describes the requirements for a zero-ohm, chip, resistor. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows and is available in wrap-around termination “B” only. 90092 - B I I I I Drawing Configuration B Number (see figure 1) 2. APPLICABLE DOCUMENTS 2.1 Governmen
6、t documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DE
7、FENSE SPECIFICATIONS MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-790 - Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electri
8、cal, Electronic, and Fiber Optic Parts Specification. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue,
9、 Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specif
10、ic exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55342 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-5534
11、2 and herein (see figure 1). 3.2.1 Termination material. The termination material shall be in accordance with MIL-PRF-55342 and code letter B. 3.2.2 Design documentation. The design documentation shall be in accordance with MIL-PRF-55342 and unless otherwise specified in the contract or purchase ord
12、er, shall be retained by the manufacturer and available for review by the acquiring activity or contractor upon request. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO.
13、 90092 REV C PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Zero-ohm chip resistor style RM1505. 3.3 Electrical characteristics. 3.3.1 Temperature range. The temperature range shall be -55C to +125C. 3.3.2 Resistance. The resistance
14、 shall not exceed 0.04 ohm. 3.4 Marking. Marking of the individual chip resistors is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLADSCCDWG90092REVC2005RESISTORCHIPFIXEDFILMZEROOHMSTYLERM1505USEDLAMILPRF3215941DLAMILPRF321594 固定 薄膜

链接地址:http://www.mydoc123.com/p-688953.html