1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 PMIC N/A PREPARED BY Jeffery Tunstall DEFENSE SUPPLY CENTER,
2、COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY Abdo Abdouni APPROVED BY Robert Heber TITLE CONNECTOR ACCESSORIES, ELECTRICAL, SHORTING CAP BACKSHELL, ENVIRONMENTAL, CATEGORY 4C OF MIL-C-85049, FOR USE WITH MIL-DTL-38999 SERIES I AND II CONNECTORS. SIZE CAGE CODE 037Z3 DWG. NO. 93032 Original date of
3、drawing 12 October 1993 A REV A PAGE 1 OF 5 AMSC N/A 5935-E674 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93032 DEFENSE SUPPLY CENTER,
4、 COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 2 FIGURE 1. Dimension and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93032 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 3 Shell si
5、ze. Shell size B dia max C dia max 9 15.0 (0.59) 19.1 (0.75) 11 18.3 (0.72) 21.6 (0.85) 13 21.3 (0.84) 25.4 (1.00) 15 24.6 (0.97) 27.9 (1.10) 17 27.7 (1.09) 31.8 (1.25) 19 31.0 (1.22) 35.6 (1.40) 21 34.0 (1.34) 38.1 (1.50) 23 37.3 (1.47) 41.9 (1.65) 25 40.4 (1.59) 44.5 (1.75) Fitting size. Fitting s
6、ize E 0.13 (.005) A 3.6 (.140) B 4.2 (.167) C 4.6 (.182) D 4.9 (.191) E 3.2 (.125) NOTES: 1. Dimensions are in millimeters. 2. Inch-pound equivalents are in parentheses. 3. Dimensions apply after plating. 4. The U.S. Government preferred system of measurements is the metric SI system. However, since
7、 this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG
8、 NO. 037Z3 93032 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 4 FIGURE 1. Dimension and configuration Continued. REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 4C, excluding cable pullout. Fastener tensile strength: Both axial and longitudinal directions shal
9、l be 25 pounds. The load shall be applied to the end of the rope. Design and construction: See figure 1. Interface dimensions shall conform to MIL-C-85049, accessory intermateability data for MIL-DTL-38999 series I and II connectors. Material: Accessory components: Aluminum alloy shall be in accorda
10、nce with Mil-C-85049. O-ring: Shall be in accordance with MIL-C-85049. Rope: Stainless steel, passivated, with insulating jacket. Fastener: Stainless steel, passivated. Body strap: Stainless steel, passivated. Finish: A, N, and W shall be in accordance with MIL-C-85049. Finish N is for space applica
11、tions only. Part or Identifying Number (PIN): The PIN shall be in accordance with the following: Example: 93032- 1 W 11 C 2 5 Drawing number Type Finish Shell size (see figure1) Fastener size (see figure 1) Attachment length 12.7 mm 6.4 mm (.50 inch .25) increments; e.g., 6 = 76.2 mm (3.00 inches).
12、Accessory length 12.7 mm 6.4 mm (.50 inch .25) increments; e.g., 5 = 63.5 mm (2.50 inches), 25.4 mm (1.00 inch) minimum length. Marking: Marking shall be in accordance with MIL-C-85049, except the PIN shall be as stated above. Provided by IHSNot for ResaleNo reproduction or networking permitted with
13、out license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93032 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 5 QUALIFICATION: Qualification inspection: Qualification inspection for the adapter specified herein shall not be required. Qualification conformance inspection: Shall be
14、in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-C-85049. Methods of inspection: Shall be in accordance with MIL-C-85049. Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The v
15、endors listed herein have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number 31461 06324 07418 93032-*-* 1/ A4116B* A4116S* 340AS001*-* 340AS002*-* S3994C*-*-* 1/ Parts must be purchased to this DSCC PIN to assure that all perfo
16、rmance requirements and tests are met. Vendor CAGE Vendor name number and address 31461 Electro Adapter, Incorporated 20640 Nordhoff Street Chatsworth, CA 91311 06324 Glenair, Incorporated 1211 Air Way Glendale, CA 91201-2497 07418 Sunbank Electronics, Incorporated 1740 Commerce Way Paso Robles, CA 93446 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
