1、 REVISION SLT DESCRIPTION DATE APPROVED A Added suggested sources of supply. Editorial changes throughout. 14 Sep 94 David E. Moore B Changes in accordance with NOR 5910-R002-96 23 May 96 Andrew R. Ernst C Added suggested source of supply. Editorial changes throughout. 31 July 2000 Kendall A. Cotton
2、gim D Added pure tin prohibition. Updated address for vendor B. Editorial changes throughout. 27 July 2006 Michael A. Radecki Prepared in accordance with ASME Y14.100 Selected item drawing REV STATUS OF PAGES REV D D D D D D PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY ROBERT E. GRILLOT DESIGN ACTIVITY DE
3、FENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 13 December 1993 CHECKED BY EDWARD H. BACK TITLE CAPACITORS, FIXED, CERAMIC, CHIP APPROVED BY DAVID E. MOORE SIZE A CODE IDENT. NO. 14933 DWG NO. 94006 REV D PAGE 1 OF 6 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOG
4、ISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 AMSC N/A 5910-E347 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 94006 REV D PAGE 2
5、 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55681 describe the requirements for ceramic, chip. 1.2 Part or Identifying Number (PIN) The complete PIN is as follows: 94006 -XX Drawing number Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are speci
6、fied in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that
7、they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the exten
8、t specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55681 - Capacitor, Chip, Multiple Layer, Fixed, Unencapsulated, Ceramic Dielectric, Established Reliability and Non-Established
9、Reliability, General Specification For. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or fr
10、om the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, howe
11、ver, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-55681 and herein (see figure 1). 3.1.1 Termination. Termination shall be solder
12、 coated and shall be solderable when tested in accordance with MIL-STD-202, method 208. 3.1.2 Tin Plated Finishes. Tin Plating is prohibited as a final finish or as an undercoat. Tin-Lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 4 percent. 3.1.3 Operating temperature
13、 range. The operating temperature range shall be -55C to +125C. (No derating of working voltage.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 94006 REV
14、D PAGE 3 1/ 3.81 typical. NOTES: 1. Dimensions are in millimeters. 2. The U.S. Government preferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the i
15、nch-pound units shall take precedence. 3. The solder coated device may exceed the above body dimensions by a maximum of 0.15 mm. FIGURE 1. Case dimensions and configuration. Dimensions L 0.050 W 0.050 T Max 1/ Y +0.25 -0.00 5.71 6.35 4.19 0.38 mm Inches 0.15 .006 0.25 .010 0.38 .015 0.50 .020 3.81 .
16、150 4.19 .165 5.71 .225 6.35 .250 TERMINATION Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 94006 REV D PAGE 4 3.2 Electrical characteristics. 3.2.1 Rated
17、 voltage. The rated voltage shall be in accordance with table I. 3.2.2 Dielectric type. The dielectric type shall be ceramic. 3.2.3 Capacitance change with temperature (TC). Capacitance change shall be less than 15 percent. 3.2.4 Operating frequency. Operating frequency shall be up to 100 MHz. 3.2.5
18、 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25C. 3.2.6 Dissipation factor (+25C). 2.5 percent maximum measured under the same conditions as capacitance. 3.2.7 Insulation resistance. MIL-STD-202, method 302 at rated voltage. At +25C: 1,000
19、megohms minimum. At +125C: 100 megohms minimum. 3.2.8 Dielectric withstanding voltage. Two times working voltage (WVDC) for 5 seconds. 3.2 9 Capacitance tolerance. K = 10 percent, M = 20 percent. 3.3 Solderability of terminals. In accordance with MIL-PRF-55681 (see 3.1.1). 3.4 Immersion cycling. In
20、accordance with MIL-PRF-55681. 3.5 Moisture resistance. In accordance with MIL-PRF-55681 with 20 continuous cycles. 3.6 Life. Two hundred percent of rated voltage for 96 hours at +125C in accordance with MIL-STD-202, method 108, test condition A. 3.7 Shock. MIL-STD-202, method 213, test condition J.
21、 3.8 Thermal shock. MIL-STD-202, method 107, test condition B. 3.9 Voltage conditioning. In accordance with MIL-PRF-55681, 100 percent of rated voltage. 3.10 Marking. Marking of the capacitor is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the
22、PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.11 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible
23、 provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.12 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.13 Wor
24、kmanship. The capacitor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection
25、 of product for delivery shall consist of all tests specified in group A of MIL-PRF-55681 provided they are listed in this drawing. PPM testing and calculation is not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUP
26、PLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 94006 REV D PAGE 5 TABLE I. Electrical characteristics. DSCC drawing 94006- Capacitance F Tolerance WVDC DSCC drawing 94006- Capacitance F Tolerance WVDC 01 .010 K 300 15 .15 K 200 02 .010 M 300 16 .15 M 200 03 .015 K 300 17 .22
27、K 200 04 .015 M 300 18 .22 M 200 05 .022 K 300 19 .33 K 150 06 .022 M 300 20 .33 M 150 07 .033 K 250 21 .47 K 150 08 .033 M 250 22 .47 M 150 09 .047 K 250 23 .68 K 150 10 .047 M 250 24 .68 M 150 11 .068 K 250 25 .82 K 100 12 .068 M 250 26 .82 M 100 13 .10 K 200 27 1.0 K 100 14 .10 M 200 28 1.0 M 100
28、 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to asc
29、ertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or De
30、fense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are inten
31、ded for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog l
32、istings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requi
33、rements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for notification of change of product to acquiring activity, if applicable. d. Requirements
34、for packaging and packing. 6.3 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by a contractor-prepared specification or drawing. 6.4 Users of record. Coordination of this document for future revisions is coordinated only with the suggested sources
35、of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus (DSCC), ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil, or by telephone (614) 692-4
36、709 or DSN 850-4709. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 94006 REV D PAGE 6 6.5 Suggested source of supply. A suggested source of supply is list
37、ed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, P. O. Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. TABL
38、E II. Similar vendor types. DSCC drawing 94006- Vendor A similar vendor PIN 1/ Vendor B similar vendor PIN 1/ 01 ATC900C103KW300 2225B103KDWUBGA 02 ATC900C103MW300 2225B103MDWUBGA03 ATC900C153KW300 2225B153KDWUBGA 04 ATC900C153MW300 2225B153MDWUBGA05 ATC900C223KW300 2225B223KDWUBGA 06 ATC900C223MW30
39、0 2225B223MDWUBGA07 ATC900C333KW250 2225B333KDWUBGA 08 ATC900C333MW250 2225B333MDWUBGA09 ATC900C473KW250 2225B473KDWUBGA 10 ATC900C473MW250 2225B473MDWUBGA11 ATC900C683KW250 2225B683KDWUBGA 12 ATC900C683MW250 2225B683MDWUBGA13 ATC900C104KW200 2225B104KDWUBGA 14 ATC900C104MW200 2225B104MDWUBGA15 ATC9
40、00C154KW200 2225B154KDWUBGA 16 ATC900C154MW200 2225B154MDWUBGA17 ATC900C224KW200 2225B224KDWUBGA 18 ATC900C224MW200 2225B224MDWUBGA19 ATC900C334KW150 2225B334KDWUBGA 20 ATC900C334MW150 2225B334MDWUBGA21 ATC900C474KW150 2225B474KDWUBGA 22 ATC900C474MW150 2225B474MDWUBGA23 ATC900C684KW150 2225B684KDWU
41、BGA 24 ATC900C684MW150 2225B684MDWUBGA25 ATC900C824KW100 2225B824KDWUBGA 26 ATC900C824MW100 2225B824MDWUBGA27 ATC900C105KW100 2225B105KDWUBGA 28 ATC900C105MW100 2225B105MDWUBGA1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Vendor Vendor CAGE
42、 Vendor name number and addressA 29990 American Technical Ceramics One Norden Lane Huntington Station, NY 11746-2142 B 0LR95 Spectrum Control Technology, Inc. 1900 West College Avenue State College, PA 16801 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
