1、REVISIONS LTR DESCRIPTION DATE APPROVED A Updated in accordance with overage review. 4/1/2009 Abdo Abdouni Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ralph Antonelli DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 C
2、HECKED BY TITLE Richard Taylor APPROVED BY Robert M. Heber CONNECTORS, ELECTRICAL, RECTANGULAR, NONENVIORNMENTAL, MINIATURE, POLARIZED SHELL, SIZE 20 PIN SIZE CAGE CODE 037Z3 DWG. NO.99013 Original date of drawing 16 June 2000 A REV A PAGE 1 OF 5 AMSC N/A 5935- E800-000 Provided by IHSNot for Resale
3、No reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 99013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE2 FIGURE 1. One piece shell, size 20 pin contacts. Provided by IHSNot for ResaleNo reproduction or networking permitted without l
4、icense from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 99013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE3 Part or Identifying number (PIN) Shell size Number of positions A B C D E G H J L 99013NAEPR-1 1 9 1.198 1.228 .651 .671 .979 .989 .324 .334 .479 .509 .229 .241 .762 .778 .432
5、.444 .020 .040 99013NAEPR-2 2 15 1.526 1.556 .989 .999 1.307 1.317 .324 .334 .479 .509 .229 .241 1.086 1.102 .432 .444 .020 .040 99013NAEPR-3 3 25 2.073 2.103 1.529 1.539 1.847 1.857 .324 .334 .479 .509 .224 .236 1.628 1.644 .432 .444 .029 .049 99013NAEPR-4 4 37 2.714 2.744 2.177 2.187 2.495 2.505 .
6、324 .334 .479 .509 .224 .236 2.276 2.292 .432 .444 .029 .049 99013NAEPR-5 5 50 2.620 2.650 2.074 2.084 2.401 2.411 .436 .446 .590 .620 .224 .236 2.181 2.197 .544 .556 .029 .049 99013SAEPR-1 1 9 1.198 1.228 .651 .671 .979 .989 .324 .334 .479 .509 .229 .241 .762 .778 .432 .444 .020 .040 99013SAEPR-2 2
7、 15 1.526 1.556 .989 .999 1.307 1.317 .324 .334 .479 .509 .229 .241 1.086 1.102 .432 .444 .020 .040 99013SAEPR-3 3 25 2.073 2.103 1.529 1.539 1.847 1.857 .324 .334 .479 .509 .224 .236 1.628 1.644 .432 .444 .029 .049 99013SAEPR-4 4 37 2.714 2.744 2.177 2.187 2.495 2.505 .324 .334 .479 .509 .224 .236
8、2.276 2.292 .432 .444 .029 .049 99013SAEPR-5 5 50 2.620 2.650 2.074 2.084 2.401 2.411 .436 .446 .590 .620 .224 .236 2.181 2.197 .544 .556 .029 .049 Inches mm Inches mm Inches mm Inches mm .002 0.05 .444 11.28 1.198 30.43 2.276 57.81 .010 0.25 .446 11.33 1.228 31.19 2.292 58.22 .020 0.51 .479 12.17 1
9、.307 33.20 2.401 60.99 .029 0.74 .509 12.93 1.317 33.45 2.411 61.24 .040 1.02 .544 13.82 1.526 38.76 2.495 63.37 .049 1.24 .556 14.12 1.556 39.52 2.505 63.63 .224 5.69 .590 14.99 1.628 41.35 2.620 66.55 .229 5.82 .620 15.75 1.644 41.76 2.650 67.31 .236 5.99 .661 16.79 1.847 46.91 2.714 68.94 .241 6.
10、12 .671 17.04 1.857 47.17 2.744 69.70 .324 8.23 .762 19.35 2.073 52.65 .334 8.48 .778 19.76 2.103 53.42 .432 10.97 1.086 27.58 2.181 55.40 .436 11.07 1.102 27.99 2.197 55.80 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless other specified, tolerance
11、 for three place decimals is .005 (0.13 mm) 4. Markings are shown for pin insert front. 5. Referenced documents shall be of the issue in effect on date of invitations for bid. 6. Rubber grommet applies only for class S connectors. 7. Maximum wire insulation used with connector is .054 (1.37 mm) diam
12、eter with grommet .068 (1.73 mm) without grommet. FIGURE 1. One piece shell, size 20 pin contacts Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 99013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A
13、REVA PAGE4 ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C to 125C. REQUIREMENTS: Requirements of drawing 98023 are applicable. Dimensions and configurations: See figure 1. Signal contact specifications Style A: (crimp removable signal contacts). PIN M39029/
14、58-369 or G-10-P1 (NASA). Shell size: One (1) through five (5). Tools: Connectors with crimp removable signal contacts shall be designated for contact insertion and removal with the applicable military tool as follows: Contact size Tool PIN 20 M81969/1-02 with metal tip Mating and unmating forces wi
15、th signalcontacts only installed (pounds): Unmating Mating Shell Size Min Max max 1 0.75 10.00 15.00 2 1.00 20.00 25.00 3 1.75 23.00 30.00 4 2.50 30.00 45.00 5 3.25 35.00 50.00 Contact resistance: Not applicable crimp removable contacts tested and qualified to SAE-AS39029. Dielectric withstanding vo
16、ltage: Altitude Humidity condition All other conditions Sea level 70, 000 600 - 1,000 325 Vibration: Test procedure EIA-364-28, condition IV. Temperature cycling: Test procedure EIA-364-32, condition I, 5 cycles, except temperature shall be -55C to 125C. Provided by IHSNot for ResaleNo reproduction
17、or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 99013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE5 Approved sources of supply are listed herein: Additional sources will be added as they become available. The vendors listed on the requirements
18、 drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ CAGE DSCC drawing PIN 00779 99013NAEPR-1 1218234-1 99013NAEPR-2 1218234-2 99013NAEPR-3 1218234-3 99013NAEPR-4 1218234-4 99013NAEPR-5 1218234-5 99013SAEPR-1 1218234-6 99013SAEPR-
19、2 1218234-7 99013SAEPR-3 1218234-8 99013SAEPR-4 1218234-9 99013SAEPR-5 1-1218234-0 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 00779 Tyco Electronics P.O. Box 3608 Harrisburg, PA 17105-3608 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
