1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add device types 10 and 11. - phn 08-12-08 Thomas M. Hess B Update boilerplate paragraphs to current requirements. Correct top-side part marking designators on sheet 10 for device types 01 through 09. - CFS 09-03-19 Thomas M. Hess Prepared in accordance wit
2、h ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV B B B B B B B B B B REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY Phu H. Nguyen APPROVED BY Thomas M. Hess
3、 TITLE MICROCIRCUIT, LINEAR, FAST-TRANSIENT-RESPONSE 1-A LOW DROPOUT VOLTAGE REGULATORS, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/03632 03-06-09 REV B PAGE 1 OF 10 AMSC N/A 5962-V046-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
4、-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a fast-transient-response1-A low dropout voltage regulators, with an operating temperature range of -40C to +125C (devic
5、e types 01 to 09) and an extended operating temperature range of -55C to +125C (device types 10 and 11). 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying th
6、e item on the engineering documentation: V62/03632 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). 1/ Device Generic Output Circuit function type voltage 01 TPS76801-EP 2/ +1.2 V to +5.5 V Fast-transient-response 1-A low-dropout vo
7、ltage regulator. 02 TPS76815-EP 2/ +1.5 V Fast-transient-response 1-A low-dropout voltage regulator. 03 TPS76818-EP 2/ +1.8 V Fast-transient-response 1-A low-dropout voltage regulator. 04 TPS76825-EP 2/ +2.5 V Fast-transient-response 1-A low-dropout voltage regulator. 05 TPS76827-EP 2/ +2.7 V Fast-t
8、ransient-response 1-A low-dropout voltage regulator. 06 TPS76828-EP 2/ +2.8 V Fast-transient-response 1-A low-dropout voltage regulator. 07 TPS76830-EP 2/ +3.0 V Fast-transient-response 1-A low-dropout voltage regulator. 08 TPS76833-EP 2/ +3.3 V Fast-transient-response 1-A low-dropout voltage regula
9、tor. 09 TPS76850-EP 2/ +5.0 V Fast-transient-response 1-A low-dropout voltage regulator. 10 TPS76801-EP 3/ +1.2 V to +5.5 V Fast-transient-response 1-A low-dropout voltage regulator. 11 TPS76850-EP 3/ +5.0 V Fast-transient-response 1-A low-dropout voltage regulator. 1.2.2 Case outline(s). The case o
10、utline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 20 JEDEC MO-153 Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip
11、 B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other _ 1/ Users are cautioned to review the manufacturers data manual for additional user information relating to these devices. 2/ Operated at -40C to +125C. 3/ Operated at -55C to +125C. Provided by IHSNot for ResaleNo reproducti
12、on or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 3 1.3 Absolute maximum ratings. 4/ Input voltage range (VI). -0.3 V to +13.5 V 5/ Voltage range at EN -0.3 V to VI + 0.3 V Maximum PG voltag
13、e +16.5 V Peak output current. Internally limited Continuous total power dissipation See dissipation rating tables Output voltage (VO) (OUT, FB) +7.0 V Operating virtual junction temperature range (TJ): Device types 01 to 09 -40C to +125C Device types 10 and 11 . -55C to +125C Storage temperature ra
14、nge (TSTG). -65C to +150C ESD rating, (HBM) 2 kV Dissipation Rating Table Ambient Temperatures Case outline Air Flow (CFM) TA 25C Power rating Derating Factor Above TA= 25C TA= 70C Power Rating TA= 85C Power Rating 0 2.9 W 23.5 mW/C 1.9 W 1.5 W X 6/ 300 4.3 W 34.6 mW/C 2.8 W 2.2 W 0 3.0 W 23.8 mW/C
15、1.9 W 1.5 W X 7/ 300 7.2 W 57.9 mW/C 4.6 W 3.8 W 1.4 Recommended operating conditions. 8/ Input voltage range (VI). 2.7 V to 10.0 V 9/ Output voltage (VO) . 1.2 V to 5.5 V Output current (IO). 0 A to 1.0 A 10/ Operating virtual junction temperature range (TJ) . -40C to +125C 10/ _ 4/ Stresses beyond
16、 those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-
17、rated conditions for extended periods may affect device reliability. 5/ All voltage values are with respect to network terminal ground. 6/ This parameter is measured with the recommended copper heat sink pattern on a 1-layer PCB, 5 in x 5 in PCB, 1 oz. copper, 2 in x 2 in coverage. 7/ This parameter
18、 is measured with the recommended copper heat sink pattern on a 8-layer PCB, 1.5 in x 2 in PCB, 1 oz. copper with layer 1, 2, 4, 5, 7, and 8 at 5% coverage (0.9 in2) and layers 3 and 6 at 100% coverage (6 in2). For more information, refer to the manufacturer technical brief SLMA002. 8/ Use of this p
19、roduct beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. 9/ To calculate the minimum input voltage for your maximum output current, use the follo
20、wing equation: VI(min)= VO(max)+ VDO(max load)10/ Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time. Provided by IHSN
21、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications fo
22、r copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A
23、. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating
24、 conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline(s). The case outline(s) shall be as s
25、hown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.5.3 Block diagrams. The block diagrams shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SU
26、PPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Test conditions VI= VO(Typ)+ 1 V IO= 1 mA, EN = 0 V CO= 10 F Operating at free air temperature range unless otherwise specified Device type
27、Min Max Unit TJ= 25C, 1.5 V VO 5.5 V VO Typ TJ= -40C to 125C, 1.5 V VO 5.5 V 01, 10 0.98 VO1.02 VOTJ= 25C, 2.7 V VIN 10 V 1.5 Typ TJ= -40C to 125C, 2.7 V VIN 10 V 02 1.470 1.530 TJ= 25C, 2.8 V VIN 10 V 1.8 Typ TJ= -40C to 125C, 2.8 V VIN 10 V 03 1.764 1.836 TJ= 25C, 3.5 V VIN 10 V 2.5 Typ TJ= -40C t
28、o 125C, 3.5 V VIN 10 V 04 2.450 2.550 TJ= 25C, 3.7 V VIN 10 V 2.7 Typ TJ= -40C to 125C, 3.7 V VIN 10 V 05 2.646 2.754 TJ= 25C, 3.8 V VIN 10 V 2.8 Typ TJ= -40C to 125C, 3.8 V VIN 10 V 06 2.744 2.856 TJ= 25C, 4.0 V VIN 10 V 3.0 Typ TJ= -40C to 125C, 4.0 V VIN 10 V 07 2.940 3.060 TJ= 25C, 4.3 V VIN 10
29、V 3.3 Typ TJ= -40C to 125C, 4.3 V VIN 10 V 08 3.234 3.366 TJ= 25C, 6.0 V VIN 10 V 5.0 Typ Output voltage (10 A to 1 A load) 2/ TJ= -40C to 125C, 6.0 V VIN 10 V 09, 11 4.900 5.100 V TJ= 25C, 10 A IO 1 A All 85 Typ Quiescent current (GND current) EN = 0 V 2/ TJ= -40C to 125C, IO= 1 A All 125 A Output
30、voltage line regulation (VO/VO) 2/ 3/ TJ= 25C, VO+ 1 V VI 10 V All 0.01 Typ %/V Load regulation All 3 Typ mV Output noise voltage BW = 200 Hz to 100 kHz, IC= 1 A, CO= 10 F, TJ= 25C 03 55 Typ Vrms Output current limit 2 A Thermal shutdown junction temperature All 150 Typ C TJ= 25C, EN = VI, 2.7 V VI
31、10 V 1 Typ Standby current TJ= -40C to 125C, EN = VI,2.7 V VI 10 V All 10 A FB input current FB = 1.5 V 01, 10 2 Typ nA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE
32、 A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Limits Test Test conditions VI= VO(Typ)+ 1 V IO= 1 mA, EN = 0 V CO= 10 F Operating at free air temperature range unless otherwise specified Device type Min Max Unit High level enabl
33、e input voltage 1.7 V Low level enable input voltage 0.9 V Power supply ripple rejection 2/ TJ= 25C, f = 1 KHz, CO= 10 F 60 Typ dB Minimum input voltage for valid PG IO(PG)= 300 A 1.1 Typ V Trip threshold voltage VOdecreasing 92 98 %VOHysteresis voltage Measured at VO0.5 Typ %VOOutput low voltage VI
34、 = 2.7 V, IO(PG)= 1 mA 0.4 V PG Leakage current V(PG)= 5 V 1 A EN = 0V -1 1 A Input current ( EN ) EN = VIAll -1 1 A TJ= 25C, IO= 1 A 500 Typ TJ= -40C to 125C, IO= 1 A 06 825 TJ= 25C, IO= 1 A 450 Typ TJ= -40C to 125C, IO= 1 A 07 675 TJ= 25C, IO= 1 A 350 Typ TJ= -40C to 125C, IO= 1 A 08 575 TJ= 25C,
35、IO= 1 A 230 Typ Dropout voltage 4/ TJ= -40C to 125C, IO= 1 A 09, 11 380 mV 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature ran
36、ge and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Minimum IN operating voltage is 2.7 V or VO(Typ)+ 1V, whichever is greater. Maximum IN voltage 10 V. 3/ If VO 1.8 V then VImax= 10
37、V, VImin= 2.7 V: Line Reg. (mV) = (%/V) x 100)V7.2V(VaxImOx 1000 If VO 2.5 V then VImax= 10 V, VImin= VO+ 1 V: Line Reg. (mV) = (%/V) x 100)V1VV(VOaxImOx 1000 4/ IN voltage equals VO(Typ) 100 mV; Device type 01 output voltage set to 3.3 V nominal with external resistor divider. Device type 02, 03, 0
38、4 and 05 dropout voltage limited by input voltage range limitations ( i.e., device type 07 input voltage needs to drop to 2.9 V for purpose of this test). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO
39、SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 7 Case X Dimensions Symbol Min Max Symbol Min Max A 1.20 E 4.30 4.50 A1 0.05 0.15 E1 6.20 6.60 b 0.19 0.30 e 0.65 TYP c 0.15 NOM L 0.50 0.75 D 6.40 6.60 Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change w
40、ithout notice. 3. Body dimensions do not include mold flash or protrusions. 4. The package thermal performance may be enhanced by bonding the thermal pad to an external thermal plane. This pad is electrically and thermally connected to the backside of the die and possibly selected leads. 5. Falls wi
41、thin JEDEC MO-153. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 8 Case X Terminal number Terminal symbol Terminal numbe
42、r Terminal symbol 1 GND/HSINK 11 GND/HSINK 2 GND/HSINK 12 GND/HSINK 3 GND 13 OUT 4 NC 14 OUT5 EN 15 FB/NC 6 IN 16 PG 7 IN 17 NC 8 NC 18 NC 9 GND/HSINK 19 GND/HSINK 10 GND/HSINK 20 GND/HSINK NC: No internal connection FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or net
43、working permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 9 Functional block diagram adjustable version. Functional block diagram fixed voltage version. FIGURE 3. Block diagrams. Provided by IHSNot for Resal
44、eNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03632 REV B PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test
45、requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labe
46、ling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained here
47、in is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guara
