1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add device type 02. - phn 08-11-19 Thomas M. Hess Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV A A A A A A A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY
2、CENTER, COLUMBUS COLUMBUS, OHIO Original date of drawing CHECKED BY Charles F. Saffle APPROVED BY Thomas M. Hess TITLE MICROCIRCUIT, DIGITAL, LOW VOLTAGE CMOS, 3-LINE TO 8-LINE DECODER/DEMULTIPLEXER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/04657 YY-MM-DD 04-03-08 REV A PAGE 1 OF
3、11 AMSC N/A 5962-V005-09 .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of
4、 a high performance 3-line to 8-line decoder/demultiplexer microcircuit, with an operating temperature range of -40C to +125C (device type 01) and an extend operating temperature range of -55C to +125C (device type 02). 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is
5、the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/04657 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Gen
6、eric Circuit function 01 1/ SN74LVC138A-EP 3-line to 8-line decoder/demultiplexer 02 2/ SN74LVC138A-EP 3-line to 8-line decoder/demultiplexer 1.2.2 Case outlines. The case outlines are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 16 MS-012 Plastic small-outline Y M
7、O-153 Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium _ 1/ Device type 01 operated at -40C to
8、 +125C 2/ Device type 02 operated at -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 3 1.3 Absolute maximum ratings. 3/ Supply volta
9、ge range (VCC) . -0.5 V to 6.5 V Input voltage range (VI). -0.5 V to 6.5 V 4/ Output voltage range (VO) . -0.5 V to VCC+ 0.5 V 4/ 5/ Input clamp current (IIK) (VI 0) -50 mA Output clamp current (IOK) (VO 0) . -50 mA Continuous output current (IO). 50 mA Continuous current through VCCor GND. 100 mA P
10、ackage thermal impedance (JA): 6/ X package . 73C/W Y package . 108C/W Storage temperature range (TSTG). -65C to 150C 7/ 1.4 Recommended operating conditions. 8/ Supply voltage range (VCC): Operating. 2.0 V to 3.6 V Data retention only 1.5 V minimum Minimum high level input voltage (VIH) (VCC= 2.7 V
11、 to 3.6 V) . 2.0 V Maximum low level input voltage (VIL) (VCC= 2.7 V to 3.6 V) 0.8 V Input voltage range (VI). 0.0 V to 5.5 V Output voltage range (VO) . 0.0 V to VCCMaximum high level output current (IOH): VCC= 2.7 V -12 mA VCC= 3.0 V -24 mA Maximum low level output current (IOL): VCC= 2.7 V 12 mA
12、VCC= 3.0 V 24 mA Maximum input transition rise or fall rate (t/v) . 10 ns/V Operating free-air temperature range (TA): Device type 01 -40C to +125C Device type 02 -55C to +125C 3/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress
13、 ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 4/ The input negative-voltage and o
14、utput voltage ratings may be exceeded if the input and output current ratings are observed. 5/ The value of VCCis provided in the recommended operating conditions table. 6/ The package thermal impedance is calculated in accordance with JESD 51-7. 7/ Long-term high-temperature storage and/or extended
15、 use at maximum recommended operating conditions may result in a reduction of overall device life. 8/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE
16、 SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 - Registered and Standard Outlines for Semiconductor Devices JEDEC STD 51-7 - High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Appl
17、ications for copies should be addressed to the Electronic Industry Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows:
18、 A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operati
19、ng conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as sho
20、wn in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Test circuit and timing waveforms. The test circ
21、uit and timing waveforms shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 5 TABLE I. Electrical performance characte
22、ristics. Limits Test Symbol Conditions VCCDevice type Min Max Unit IOH= -100 A 2.7 V to 3.6 V VCC 0.2 2.7 V 2.2 IOH= -12 mA 3.0 V 2.4 High level output voltage VOHIOH= -24 mA 3.0 V 2.2 V IOL= 100 A 2.7 Vto 3.6 V 0.2 IOL= 12 mA 2.7 V 0.4 Low level output voltage VOLIOL= 24 mA 3.0 V 0.55 V Input curre
23、nt IIVI= 5.5 V or GND 3.6 V 5 A Quiescent supply current ICCVI= VCCor GND IO= 0 A 3.6 V 10 A Quiescent supply current delta ICCOne input at VCC 0.6 V, Other inputs at VCCor GND 2.7 V to 3.6 V 500 A Input capacitance CiVI= VCCor GND 3.3 V 5 TYP pF 2.5 V 26 TYP Power dissipation capacitance per gate C
24、pdf = 10 MHz 3.3 V 27 TYP pF 2.7 V 7.9 Propagation delay time, A or B or C to Y 3.3 V 0.3 V 1 6.7 2.7 V 7.4 Propagation delay time, G2A or G2B to Y 3.3 V 0.3 V 1 6.5 2.7 V 6.4 Propagation delay time, G1 to Y tpdSee figure 5. 3.3 V 0.3 V All 1 5.8 ns Provided by IHSNot for ResaleNo reproduction or ne
25、tworking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 6 Case X Dimensions Millimeters Inches Millimeters Inches Symbol Min Max Min Max Symbol Min Max Min Max A - 0.069 - 1.75 E 0.150 0.157 3.81 4.00 A1
26、0.004 0.010 0.10 0.25 E1 0.228 0.244 5.80 6.20 b 0.014 0.020 0.35 0.51 e 0.050 BSC 1.27 BSC c 0.008 NOM 0.20 NOM L 0.016 0.044 0.40 1.12 D 0.386 0.394 9.80 10.00 NOTES: 1. All linear dimensions are in inches (millimeters). 2. This case outline is subject to change without notice. 3. Body dimensions
27、do not include mold flash or protrusion, not to exceed 0.006 inches (0.15 mm). 4. Falls within JEDEC MS-012. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO.
28、 16236 DWG NO. V62/04657 REV A PAGE 7 Case Y Dimensions Millimeters Inches Millimeters Inches Symbol Min Max Min Max Symbol Min Max Min Max A - 1.20 - 0.047 E 4.30 4.50 0.169 0.177 A1 0.05 0.15 0.002 0.006 E1 6.20 6.60 0.244 0.260 b 0.19 0.30 0.007 0.012 e 0.65 BSC 0.026 BSC c 0.15 NOM 0.006 NOM L 0
29、.50 0.75 0.020 0.030 D 4.90 5.10 0.193 0.201 NOTES: 1. All linear dimensions are in millimeters (inches). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.15 millimeters (0.006 in). 4. Fall within JEDEC MO-153. FIGU
30、RE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 8 Enable Inputs Select Inputs Outputs G1 G2A G2B C B A Y0 Y1 Y2 Y
31、3 Y4 Y5 Y6 Y7 X X L H H H H H H H H H X X L L L L L L L L X H X L L L L L L L L X X X L L L L H H H H X X X L L H H L L H H X X X L H L H L H L H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H
32、H H H H H H H H H H L H = High voltage level L = Low voltage level X = Immaterial FIGURE 2. Truth table. FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 162
33、36 DWG NO. V62/04657 REV A PAGE 9 Device type 01 Case outlines X and Y Terminal number Terminal symbol 1 A 2 B 3 C 4 G2A 5 G2B 6 G1 7 Y7 8 GND 9 Y6 10 Y5 11 Y4 12 Y3 13 Y2 14 Y1 15 Y0 16 VCCFIGURE 4. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without l
34、icense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 10 NOTES: 1. CLincludes probe and jig capacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO= 50 . 3. tPLHand tPHLare
35、the same as tpd. 4. The outputs are measured one at a time with one input transition per measurement. FIGURE 5. Test circuit and timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A C
36、ODE IDENT NO. 16236 DWG NO. V62/04657 REV A PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic se
37、nsitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sen
38、sitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right
39、to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor i
40、tem drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/04657-01XE 01295 SN74LVC138AQDREP C138AEP V62/04657-01YE 01295 SN74LVC138AQPWREP C138AEP V62/04657-02YE 01295 SN74LVC138AMPWTEP C138AME 1/ The vendor item drawing establishes an adminis
41、trative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
