1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add device type 02 and case outline Y. Update boilerplate. - CFS 06-07-21 Thomas M. Hess B Update boilerplate paragraphs to current requirements. - PHN 13-09-09 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITI
2、ME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV B B B B B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Original date o
3、f drawing CHECKED BY Phu H. Nguyen TITLE MICROCIRCUIT, DIGITAL, SINGLE 2-INPUT POSITIVE AND GATE, MONOLITHIC SILICON YY MM DD 04-07-07 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/04733 REV B PAGE 1 OF 13 AMSC N/A 5962-V078-13Provided by IHSNot for ResaleNo reproduction or net
4、working permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance single 2-input positive AND gate microcircuit, with an op
5、erating temperature range of -40C to +85C for device 01, and -55C to +125C for device 02. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the e
6、ngineering documentation: V62/04733 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 SN74LVC1G08-EP Single 2-input positive AND gate. 02 SN74LVC1G08-EP Single 2-input positive AND gate. 1.2.
7、2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 JEDEC MO-203 Plastic small outline Y 5 JEDEC MO-178 Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by t
8、he device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE ID
9、ENT NO. 16236 DWG NO. V62/04733 REV B PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range, (VCC) . -0.5 V to +6.5 V Input voltage range, (VI) . -0.5 V to +6.5 V 2/ Voltage range applied to any output in the high impedance or power-off stage, (VO) -0.5 V to +6.5 V 2/ Voltage range applied to
10、 any output in the high or slow state, (VO) . -0.5 V to VCC+ 0.5 V 2/ 3/ Input clamp current, (IIK) (VI 0) -50 mA Output clamp current, (IOK) (VO 0) . -50 mA Continuous output current, (IO) . 50 mA Continuous current through VCCor GND 100 mA Package thermal impedance (JA): Case X 252C/W 4/ Case Y 25
11、6C/W 4/ Storage temperature range, (TSTG) -65C to +150C 1.4 Recommended operating conditions. 5/ Supply voltage, (VCC): Operating +1.65 V to +5.5 V Minimum data retention only . +1.5 V Minimum high level input voltage, (VIH): VCC= 1.65 V to 1.95 V +0.65 x VCCVCC= 2.3 V to 2.7 V +1.7 V VCC= 3.0 to 3.
12、6 V . +2.0 V VCC= 4.5 V to 5.5 V +0.7 x VCCMaximum low level input voltage, (VIL): VCC= 1.65 V to 1.95 V +0.35 x VCCVCC= 2.3 V to 2.7 V +0.7 V VCC= 3.0 to 3.6 V . +0.8 V VCC= 4.5 V to 5.5 V +0.3 x VCCInput voltage, (VI) 0.0 V to 5.5 V Output voltage, (VO) 0.0 V to VCCMaximum high level output curren
13、t, (IOH): VCC= 1.65 V . -4 mA VCC= 2.3 V . -8 mA VCC= 3.0 V . -16 mA VCC= 3.0 V -24 mA VCC= 4.5 V . -32 mA Maximum low level output current, (IOL): VCC= 1.65 V . 4 mA VCC= 2.3 V . 8 mA VCC= 3.0 V . 16 mA VCC= 3.0 V 24 mA VCC= 4.5 V . 32 mA Maximum Input transition rise or fall rate (t/v): VCC= 1.8 V
14、 0.15 V, 2.5 V 0.2 V 20 ns/V VCC= 3.3 V 0.3 V . 10 ns/V VCC= 5 V 0.5 V 5 ns/V 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those
15、indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input and output negative voltage ratings may exceeded if the input and output current ratings are observed. 3/ The value of VCC
16、is provided in the recommended operating conditions table. 4/ The package thermal impedance is calculated in accordance with JESD 51-7. 5/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo reproduction or networking permitted
17、 without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 4 1.4 Recommended operating conditions - Continued. Operating free air temperature, (TA): Device 01 -40C to +85C Device 02 -55C to +125C 2. APPLICABLE DOCUMENTS JEDEC
18、 SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 Registered and Standard Outlines for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201-2107). 3. REQU
19、IREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with th
20、e manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. Th
21、e design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline(s). The case outline(s) shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall
22、be as shown in figure 3. 3.5.4 Function table. The function table shall be as shown in figure 4. 3.5.5 Load circuit and voltage waveforms. The load circuit and timing waveforms shall be as specified in figure 5 and 6. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
23、se from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions Device 01: -40C TA +85C Device 02: -55C TA +125C unless otherwise specified VCCDevice type Limits Unit
24、Min Max High level output voltage VOHIOH= -100 A 1.65 V to 5.5 V All VCC 0.1 V IOH= -4 mA 1.65 V 1.2 IOH= -8 mA 2.3 V 1.9 IOH= -16 mA 3.0 V 2.4 IOH= -24 mA 2.3 IOH= -32 mA 4.5 V 3.8 Low level output voltage VOLIOL= 100 A 1.65 V to 5.5 V 0.1 V IOL= 4 mA 1.65 V 0.45 IOL= 8 mA 2.3 V 0.3 IOL= 16 mA 3.0
25、V 0.4 IOL= 24 mA 0.55 IOL= 32 mA 4.5 V 0.55 Input current A or B inputs IIVI= 5.5 V or GND 0 to 5.5 V 5 A Input/output power off leakage current IoffVIor VO= 5.5 V 0 V 10 A Quiescent supply current ICCVI= 5.5 V or GND, IO= 0 1.65 V to 5.5 V 10 A Quiescent supply current delta ICCOne input at VCC 0.6
26、 V, Other inputs at VCCor GND 3 V to 5.5 V 500 A Input capacitance CiVI= VCCor GND, VCC = 3.3 V, TA= 25C 3.3 V 4 Typ pF Propagation delay time from input A or B to output Y tpdCL= 15 pF See figure 5 1.8 V 0.15 V 01 1.5 7.2 ns 2.5 V 0.2 V 0.7 4.4 3.3 V 0.3 V 0.8 3.6 5 V 0.5 V 0.8 3.4 Propagation dela
27、y time from input A or B to output Y tpdCL= 30 pF or 50 pF See figure 6 1.8 V 0.15 V 2.4 8 ns 2.5 V 0.2 V 1.1 5.5 3.3 V 0.3 V 1 4.5 5 V 0.5 V 1 4 Propagation delay time from input A or B to output Y tpdCL= 50 pF See figure 6 1.8 V 0.15 V 02 2.4 11 ns 2.5 V 0.2 V 1.1 7.5 3.3 V 0.3 V 1 6.5 5 V 0.5 V 1
28、 5 Power dissipation capacitance Cpdf = 10 MHz TA= 25C 1.8 V All 21 Typ pF 2.5 V 24 Typ 3.3 V 26 Typ 5.0 V 31 Typ 1. Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be
29、 tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
30、-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 6 Case X Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion. 4. Falls within JED
31、EC MO-203. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 7 Case X Symbol Dimensions Inches Millimeters Min Max Min Max
32、A .031 .043 0.80 1.10 A1 .000 .004 0.00 0.10 b .006 .012 0.15 0.30 c .005 NOM 0.13 NOM D .072 .084 1.85 2.15 E .043 .055 1.10 1.40 E1 .070 .094 1.80 2.40 e .025 BSC 0.65 BSC L .010 .018 0.26 0.46 L1 .006 TYP 0.15 TYP FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction o
33、r networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 8 Case Y Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not incl
34、ude mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 per side. 4. Falls within JEDEC MO-178, variation AA. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS C
35、OLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 9 Case Y Symbol Dimensions Inches Millimeters Min Max Min Max A - .057 - 1.45 A1 .000 .006 0.00 0.15 b .012 .020 0.30 0.50 c .003 .009 0.08 0.22 D .108 .120 2.75 3.05 E .057 .069 1.45 1.75 E1 .102 .118 2.60 3.00 e .037 BSC 0.95 B
36、SC L .012 .022 0.30 0.55 L1 .010 BSC 0.25 BSC FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 10 Cases X and
37、Y Pin No. Signal name 1 A 2 B 3 GND 4 Y 5 VCCFIGURE 2. Terminal connections. FIGURE 3. Logic diagram. Inputs Output Y A B H H H L X L X L L FIGURE 4. Function Table Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUM
38、BUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 11 Notes: 1. CLincludes probe and test fixture capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal co
39、nditions such that the output is high, except when disabled by the output control. 3. All input pulses are supplied by generators having following characteristics: PRR 10 MHz, ZO= 50 . 4. The outputs are measured one at a time with one transition per measurement. 5. tPLZand tPHZare the same tdis. 6.
40、 tPZLand tPZHare the same ten. 7. tPLHand tPHLare the same tpd. 8. All parameters and waveforms are not applicable to all devices. FIGURE 5. Load circuit and voltage waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, CO
41、LUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 12 Notes: 1. CLincludes probe and jig capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal
42、 conditions such that the output is high, except when disabled by the output control. 3. All input pulses are supplied by generators having following characteristics: PRR 10 MHz, ZO= 50 . 4. The outputs are measured one at a time with one transition per measurement. 5. tPLZand tPHZare the same tdis.
43、 6. tPZLand tPZHare the same ten. 7. tPLHand tPHLare the same tpd. 8. All parameters and waveforms are not applicable to all devices. FIGURE 6. Load circuit and voltage waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER,
44、 COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04733 REV B PAGE 13 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include pr
45、oper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practice
46、s for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device
47、 manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE cod
