1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add device type 02 and package Y. - PHN 06-08-09 Thomas M. Hess B Correct the device package top-side markings. Update boilerplate to latest requirements. - CFS 07-07-10 Thomas M. Hess C Update boilerplate paragraphs to current requirements. - PHN 13-09-09
2、Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV C C C C C C C C C C C PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY P
3、hu H. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing CHECKED BY Phu H. Nguyen TITLE MICROCIRCUIT, DIGITAL, SINGLE 2-INPUT POSITIVE OR GATE, MONOLITHIC SILICON YY MM DD 04-07-07 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/04734 REV C
4、PAGE 1 OF 11 AMSC N/A 5962-V079-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requir
5、ements of a high performance single 2-input positive OR gate microcircuit, with an operating temperature range of -40C to +85C and extended temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item
6、drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/04734 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 1/ SN74LVC1G32-EP S
7、ingle 2-input positive OR gate. 02 2/ SN74LVC1G32-EP Single 2-input positive OR gate. 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 JEDEC MO-203 Plastic small outline package Y 5 JEDEC MO-178 Plastic small outline packa
8、ge 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1/ Operate at -40C to +85C. 2/ Operate at -55C to +125C
9、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 3 1.3 Absolute maximum ratings. 3/ Supply voltage range, (VCC) . -0.5 V to +6.5 V Input voltage
10、range, (VI) . -0.5 V to +6.5 V 4/ Voltage range applied to any output in the high impedance or power-off stage, (VO) -0.5 V to +6.5 V 4/ Voltage range applied to any output in the high or slow state, (VO) . -0.5 V to VCC+ 0.5 V 4/ 5/ Maximum input clamp current, (IIK) (VI 0) -50 mA Maximum output cl
11、amp current, (IOK) (VO 0) -50 mA Maximum continuous output current, (IO) . 50 mA Maximum continuous current through VCCor GND 100 mA Package thermal impedance (JA): Case X . 252C/W 6/ Case Y . 324.1C/W 6/ Storage temperature range, (TSTG) -65C to +150C 1.4 Recommended operating conditions. 7/ Supply
12、 voltage, (VCC): Operating +1.65 V to +5.5 V Minimum data retention only . +1.5 V Minimum high level input voltage, (VIH): VCC= 1.65 V to 1.95 V +0.65 x VCCVCC= 2.3 V to 2.7 V +1.7 V VCC= 3.0 to 3.6 V . +2.0 V VCC= 4.5 V to 5.5 V +0.7 x VCCMaximum low level input voltage, (VIL): VCC= 1.65 V to 1.95
13、V +0.35 x VCCVCC= 2.3 V to 2.7 V +0.7 V VCC= 3.0 to 3.6 V . +0.8 V VCC= 4.5 V to 5.5 V +0.3 x VCCInput voltage, (VI) 0.0 V to 5.5 V Output voltage, (VO) 0.0 V to VCCMaximum high level output current, (IOH): VCC= 1.65 V . -4 mA VCC= 2.3 V . -8 mA VCC= 3.0 V . -16 mA VCC= 3.0 V . -24 mA VCC= 4.5 V . -
14、32 mA 3/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Expos
15、ure to absolute-maximum-rated conditions for extended periods may affect device reliability. 4/ The input and output negative voltage ratings may exceeded if the input and output current ratings are observed. 5/ The value of VCCis provided in the recommended operating conditions table. 6/ The packag
16、e thermal impedance is calculated in accordance with JESD 51-7. 7/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS,
17、OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 4 1.4 Recommended operating conditions.- Continued. Maximum low level output current, (IOH): VCC= 1.65 V . 4 mA VCC= 2.3 V . 8 mA VCC= 3.0 V . 16 mA VCC= 3.0 V . 24 mA VCC= 4.5 V . 32 mA Maximum Input transition rise or fall rate (t/v): V
18、CC= 1.8 V 0.15 V, 2.5 V 0.2 V 20 ns/V VCC= 3.3 V 0.3 V . 10 ns/V VCC= 5 V 0.5 V 5 ns/V Operating free air temperature, (TA): Case X -40C to +85C Case Y -55C to +125C 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be add
19、ressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name,
20、CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electr
21、ical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline(s). The case outline(s) shall be as shown in 1.2.2 and figu
22、re 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Function table. The function table shall be as shown in figure 4. 3.5.5 Load circuit and voltage waveforms. The load circuit and timin
23、g waveforms shall be as specified in figure 5 and 6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 5 TABLE I. Electrical performance characteris
24、tics. 1/ Test Symbol Conditions -40C TA +85C 2/ -55C TA +125C 3/ unless otherwise specified VCCLimits Unit Min Max High level output voltage VOHIOH= -100 A 1.65 V to 5.5 V VCC 0.1 V IOH= -4 mA 1.65 V 1.2 IOH= -8 mA 2.3 V 1.9 IOH= -16 mA 3.0 V 2.4 IOH= -24 mA 2.3 IOH= -32 mA 4.5 V 3.8 Low level outpu
25、t voltage VOLIOL= 100 A 1.65 V to 5.5 V 0.1 IOL= 4 mA 1.65 V 0.45 IOL= 8 mA 2.3 V 0.3 IOL= 16 mA 3.0 V 0.4 IOL= 24 mA 0.55 IOL= 32 mA 4.5 V 0.55 Input current A or B inputs IIVI= 5.5 V or GND 0 to 5.5 V 5 A Input/output power off leakage current IoffVIor VO= 5.5 V 0 10 A Quiescent supply current ICC
26、VI= 5.5 V or GND, IO= 0 1.65 V to 5.5 V 10 A Quiescent supply current delta ICCOne input at VCC 0.6 V, Other inputs at VCCor GND 3 V to 5.5 V 500 A Input capacitance CiVI= VCCor GND, VCC = 3.3 V, TA= 25C 3.3 V 4 Typ pF Propagation delay time from input A or B to output Y tpdCL= 15 pF See figure 5 1.
27、8 V 0.15 V 1.9 7.2 ns 2.5 V 0.2 V 0.8 4.4 3.3 V 0.3 V 0.9 3.6 5 V 0.5 V 0.8 3.4 Propagation delay time from input A or B to output Y tpdCL= 30 pF or 50 pF See figure 6 1.8 V 0.15 V 2.8 8 2.5 V 0.2 V 1.2 5.5 3.3 V 0.3 V 1.1 4.5 5 V 0.5 V 1 4 Power dissipation capacitance Cpdf = 10 MHz, TA= 25C 1.8 V
28、20 Typ pF 2.5 V 20 Typ 3.3 V 21 Typ 5.0 V 22 Typ 1. Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may
29、not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2. For device type 01 and 02. 3. For device type 02. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE S
30、UPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 6 Case X Dimensions Symbol Inches Millimeter Symbol Inches Millimeter Min Max Min Max Min Max Min Max A .031 .043 0.80 1.10 E .043 .055 1.10 1.40 A1 .000 .004 0.00 0.10 E1 .070 .094 1.80 2.40 b .006 .012 0
31、.15 0.30 e .025 BSC 0.65 BSC c .005 NOM 0.13 NOM L .010 .018 0.26 0.46 D .072 .084 1.85 2.15 L1 .006 TYP 0.15 TYP Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion. 4. Fall within JEDEC
32、MO-203. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 7 Case Y Dimensions Symbol Inches Millimeter Symbol Inches Millim
33、eter Min Max Min Max Min Max Min Max A .057 1.45 E .057 .068 1.45 1.75 A1 .000 .006 0.00 0.15 E1 .102 .117 2.60 3.00 b .012 .020 0.30 0.50 e .037 BSC 0.95 BSC c .003 .009 0.08 0.22 L .012 .021 0.30 0.55 D .107 .119 2.75 3.05 L1 .010 NOM 0.25 NOM Notes: 5. All linear dimensions are in millimeters. 6.
34、 This drawing is subject to change without notice. 7. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 mm per side 8. Fall within JEDEC MO-178 variation AA FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or net
35、working permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 8 Case X Pin No. Signal name 1 A 2 B 3 GND 4 Y 5 VCCFIGURE 2. Terminal connections. FIGURE 3. Logic diagram. Inputs Output Y A B H X H X H H L L L FI
36、GURE 4. Function Table Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 9 Notes: 1. CLincludes probe and test fixture capacitance. 2. Waveform 1 is
37、 for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. 3. All input pulses are supplied by generators having follow
38、ing characteristics: PRR 10 MHz, ZO= 50 . 4. The outputs are measured one at a time with one transition per measurement. 5. tPLZand tPHZare the same tdis. 6. tPZLand tPZHare the same ten. 7. tPLHand tPHLare the same tpd. 8. All parameters and waveforms are not applicable to all devices. FIGURE 5. Lo
39、ad circuit and voltage waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 10 Notes: 1. CLincludes probe and jig capacitance. 2. Waveform 1
40、 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. 3. All input pulses are supplied by generators having fol
41、lowing characteristics: PRR 10 MHz, ZO= 50 . 4. The outputs are measured one at a time with one transition per measurement. 5. tPLZand tPHZare the same tdis. 6. tPZLand tPZHare the same ten. 7. tPLHand tPHLare the same tpd. 8. All parameters and waveforms are not applicable to all devices. FIGURE 6.
42、 Load circuit and voltage waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04734 REV C PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The ma
43、nufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREP
44、ARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS cl
45、ass 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s)
46、 of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.m
47、il/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking 2/ V62/04734-01XE 01295 SN74LVC1G32IDCKREP CG0 V62/04734-02XE 01295 SN74LVC1G32MDCKREP BYB V62/04734-02YE 01295 SN74LVC1G32MDBVREP SBGM 1/ The vendor item drawing
48、 establishes an administrative control number for identifying the item on the engineering documentation. 2/ The actual top side marking has one additional character that designates the assembly/test site. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 6601
