1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing
2、YY-MM-DD CHECKED BY TOM HESS APPROVED BY RAYMOND MONNIN TITLE MICROCIRCUIT, DIGITAL-LINEAR, 3 V TO 5.5 V MULTICHANNEL RS-232 LINE DRIVER / RECEIVER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/06623 06-04-27 REV PAGE 1 OF 15 AMSC N/A 5962-V061-06 Provided by IHSNot for ResaleNo repro
3、duction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 3 V to 5.5 V multichannel RS-232 line driver
4、/ receiver microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering
5、documentation: V62/06623 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 MAX3232-EP 3 V to 5.5 V multichannel RS-232 line driver / receiver 1.2.2 Case outline(s). The case outline(s) are as
6、 specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 16 MO-150 Plastic small outline Y 16 MO-153 Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot
7、 solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 3 1.3 Absolute
8、maximum ratings. 1/ Supply voltage range (VCC) -0.3 V to 6 V 2/ Positive output supply voltage range (V+) -0.3 V to 7 V 2/ Negative output supply voltage range (V-) . 0.3 V to -7 V 2/ Supply voltage difference (V+ - V-) 13 V 2/ Input voltage range (VI): Drivers -0.3 V to 6 V Receivers . -25 V to 25
9、V Output voltage range (VO): Drivers -13.2 V to 13.2 V Receivers . -0.3 V to VCC+ 0.3 V Package thermal impedance (JA): 3/ Case X . 82C/W Case Y . 108C/W Operating virtual junction temperature (TJ) 150C Storage temperature range (Tstg) -65C to +150C 1.4 Recommended operating conditions. 4/ Supply vo
10、ltage range (VCC): VCC= 3.3 V 3 V to 3.6 V VCC= 5 V . 4.5 V to 5.5 V Driver high level input voltage (VIH) at DIN pins: VCC= 3.3 V 2 V minimum VCC= 5 V . 2.4 V minimum Driver low level input voltage (VIL) at DIN pins . 0.8 V maximum Driver input voltage (VI) at DIN pins . 0 V to 5.5 V Receiver input
11、 voltage (VI) . -25 V to 25 V Operating free air temperature (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond th
12、ose indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. See figure 6. 2/ All voltages are with respect to network GND. 3/ Maximum power dissipation is a function of TJ(max), JA, and TA. T
13、he maximum allowable power dissipation at any allowable ambient temperature is PD= (TJ(max) TA) / JA. Operating at the absolute maximum TJof 150C can affect reliability. 4/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/
14、or distributor maintain no responsibility or liability for product used beyond the stated limits. See figure 6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/066
15、23 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Mark
16、ing. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers p
17、art number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, constru
18、ction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Truth table. The truth table shall be as shown in figure 3.
19、3.5.4 Logic diagram. The logic diagram shall be as shown in figure 4. 3.5.5 Timing waveforms and test circuits. The timing waveforms and test circuits shall be as shown in figure 5. 3.5.6 Typical operating circuit. The typical operating circuit shall be as shown in figure 6. Provided by IHSNot for R
20、esaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions 2/ see figure 6Temperature, TA Device ty
21、pe Min Max Unit Supply current ICCNo load, VCC= 3.3 V to 5 V -55C to +125C 01 2 mA Driver section High level output voltage VOHDOUT at RL= 3 k to GND, DIN = GND -55C to +125C 01 5 V Low level output voltage VOLDOUT at RL= 3 k to GND, DIN = VCC-55C to +125C 01 5 V High level input current IIHVI= VCC-
22、55C to +125C 01 1 A Low level input current IILVIat GND -55C to +125C 01 1 A Short circuit output 3/ current IOSVCC= 3.6 V, VO= 0 V -55C to +125C 01 60 mA VCC= 5.5 V, VO= 0 V 60 Output resistance roVCC, V+, and V- = 0 V, VO= 2 V -55C to +125C 01 300 Switching characteristics section Maximum data rat
23、e CL= 1000 pF, RL= 3 k, one DOUT switching, see figure 5 -55C to +125C 01 150 kbit/s Pulse skew 4/ tsk(p)CL= 150 pF to 2500 pF, RL= 3 k to 7 k, see figure 5 +25C 01 300 typical 5/ ns Slew rate, transition region SR(tr) RL= 3 k to 7 k, VCC= 3.3 V, CL= 150 pF to 1000 pF, see figure 5 -55C to +125C 01
24、6 30 V/s RL= 3 k to 7 k, VCC= 3.3 V, CL= 150 pF to 2500 pF, see figure 5 4 30 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623
25、REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions 2/ see figure 6Temperature, TA Device type Min Max Unit Supply current ICCNo load, VCC= 3.3 V to 5 V -55C to +125C 01 2 mA Receiver section High level output voltage VOHIOH= -1 mA -55C to +125C 01
26、VCC 0.6 V Low level output voltage VOLIOL= 1.6 mA -55C to +125C 01 0.4 V Positive going input threshold voltage VIT+VCC= 3.3 V -55C to +125C 01 2.4 V VCC= 5 V 2.4 Negative going input threshold voltage VIT+VCC= 3.3 V -55C to +125C 01 0.6 V VCC= 5 V 0.8 Input hysteresis (VIT+- VIT-) Vhys+25C 01 0.3 t
27、ypical 5/ V Input resistance riVI= 3 V to 25 V -55C to +125C 01 3 8 k Switching characteristics section Propagation delay time, low to high level output tPLHCL= 150 pF +25C 01 300 typical 5/ ns Propagation delay time, high to low level output tPHLCL= 150 pF +25C 01 300 typical 5/ ns Pulse skew 4/ ts
28、k(p)+25C 01 300 typical 5/ ns 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be
29、tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Test conditions are C1-C4 = 0.1 F at VCC= 3.3 V 0.3 V; C1 = 0.047 F, C2 C4 = 0.33 F at VCC= 5 V 0.5 V. 3/ Short circuit durations should be controlled to prevent exceeding the
30、device absolute power dissipation ratings, and not more than one output should be shorted at a time. 4/ Pulse skew is defined as | tPLH tPHL| of each channel of the same device. 5/ All typical values are at VCC= 3.3 V or VCC= 5 V, and TA= +25C. Provided by IHSNot for ResaleNo reproduction or network
31、ing permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 7 Case X FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER,
32、COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 8 Case X - continued Dimensions Inches Millimeters Symbol Min Max Min Max A - .078 - 2.00 A1 .001 - 0.05 - b .008 .014 0.22 0.38 c .003 .009 0.09 0.25 D .232 .255 5.90 6.50 E .196 .220 5.00 5.60 E1 .291 .322 7.40 8.20 e .
33、025 nominal 0.65 nominal L .021 .037 0.55 0.95 NOTES: 1. All linear dimensions are in millimeters, inch equivalents are given for general information only. 2. Body dimensions do not include mold flash or protrusion, not to exceed 0.15 millimeter ( .006 inch ) 3. Fall within JEDEC MO-150. FIGURE 1. C
34、ase outlines Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 9 Case Y FIGURE 1. Case outlines Continued. Provided by IHSNot for ResaleNo
35、reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 10 Case Y - continued Dimensions Inches Millimeters Symbol Min Max Min Max A - .047 - 1.20 A1 .001 .005 0.05 0.15 b .007 .011 0.19 0
36、30 c .005 nominal .015 nominal D .192 .200 4.90 5.10 E .169 .177 4.30 4.50 E1 .244 .259 6.20 6.60 e .025 nominal 0.65 nominal L .019 .029 0.50 0.75 NOTES: 1. All linear dimensions are shown in millimeters, inch equivalents are given for general information only. 2. Body dimensions do not include mo
37、ld flash or protrusion not to exceed 0.15 mm (.006 inch). 3. Falls within JEDEC MO-153. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DW
38、G NO. V62/06623 REV PAGE 11 Device type 01 Case outlines X and Y Terminal number Terminal symbol 1 C1+ 2 V+3 C1- 4 C2+ 5 C2- 6 V- 7 DOUT2 8 RIN2 9 ROUT2 10 DIN2 11 DIN1 12 ROUT1 13 RIN1 14 DOUT1 15 GND 16 VCCFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking p
39、ermitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 12 Each driver Each receiver Input DIN Output DOUT Input RIN Output ROUT L H L H H L H L - - Open H H = High level L = Low level Open = Input disconnected or co
40、nnected driver off FIGURE 3. Truth table. ( Positive logic ) FIGURE 4. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 13 NOTES: 1. C
41、Lincludes probe and jig capacitance. 2. The pulse generator has the following characteristics: ZO= 50 , 50% duty cycle, tr 10 ns, tf 10 ns. FIGURE 5. Timing waveforms and test circuits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY C
42、ENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 14 VCCversus capacitor values VCCC1 C2, C3, C4 3.3 V 0.3 V 0.1 F 0.1 F 5 V 0.5 V 0.047 F 0.33 F 3 V to 5.5 V 0.1 F 0.47 F NOTES: 1. C3 can be connected to VCCor GND. 2. Resistor values shown are nominal. 3. Nonpola
43、rized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be connected as shown. FIGURE 6. Typical operating circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBU
44、S COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06623 REV PAGE 15 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handl
45、ing of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for elec
46、trostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufactu
47、rer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Package 2/ Top s
