1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate paragraphs to current requirements. - ro 12-06-06 C. SAFFLE CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE
2、 REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY TOM HESS TITLE MICROCIRCUIT, CMOS, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON 06
3、-07-07 APPROVED BY RAYMOND MONNIN SIZE A CODE IDENT. NO. 16236 DWG NO. V62/06641 REV A PAGE 1 OF 11 AMSC N/A 5962-V070-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG N
4、O. V62/06641 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance CMOS operational amplifier microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item
5、of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/06641 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circ
6、uit function 01 OPA336-EP CMOS operational amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 MO-178-AA Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes a
7、s provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO
8、SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) 7.5 V Signal input terminals: Voltage range . -VS 0.3 V to +VS+ 0.3 V 2/ Current . 10 mA 2/ Output short circuit . Continuous 3/ Storage temperature range (TSTG) -55C to +125C Junction tem
9、perature (TJ) +150C Lead temperature (soldering, 10 seconds) . +300C Electrostatic discharge rating: Charged device model (CDM) 1000 V Human body model (HBM) . 500 V Machine model (MM) . 100 V Package thermal impedance (JA) . 200C/W 1.4 Recommended operating conditions. 4/ Supply voltage range (VS)
10、2.3 V to 5.5 V Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indic
11、ated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Input terminals are diode clamped to the power supply rails. Input signals that can swing more than 0.3 V beyond the supply rails should
12、be current limited to 10 mA or less. 3/ Short circuit to ground, one amplifier per package. 4/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond
13、 the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC Solid State Technology Association JEDEC PUB 9
14、5 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the JEDEC Office, 3103 North 10th Street, Suite 240-S, Arlington, VA 22201-2107 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked wi
15、th the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) abo
16、ve. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herei
17、n. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER,
18、COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/Temperature, TADevice type Limits Unit Min Max Offset voltage section Input offset voltage VOS+25C 01 500 V -55C to +125C 950 Input offset v
19、oltage versus power supply PSRR VS= 2.3 V to 5.5 V +25C 01 100 V/V -55C to +125C 150 Channel separation, dc +25C 01 0.1 typical Input bias current section Input bias current +25C 01 10 pA -55C to +125C 200 Input offset current IOS+25C 01 60 pA Noise section Input voltage noise f = 0.1 Hz to 10 Hz +2
20、5C 01 3 typical Vp-p Input voltage noise density enf = 1 kHz +25C 01 40 typical nV / Hz Current noise density inf = 1 kHz +25C 01 30 typical fA / Hz Input voltage range section Common mode voltage range VCM+25C 01 -0.2 +VS- 1 V Common mode rejection ratio CMRR -0.2 V VCM ( +VS) 1 V +25C 01 76 dB -55
21、C to +125C 72 Input impedance section Differential input impedance 3/ +25C 01 1013| 2 typical | pF Common mode input impedance 3/ +25C 01 1013| 4 typical | pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPP
22、LY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TA Device type Limits Unit Min Max Open loop gain section Open loop voltage gain AOL100 mV VO (+VS) 100 mV
23、, RL= 25 k +25C 01 90 dB 500 mV VO (+VS) 500 mV, RL= 5 k 90 100 mV VO (+VS) 100 mV, RL= 25 k -55C to +125C 82 500 mV VO (+VS) 500 mV, RL= 5 k 89 Frequency response section Gain bandwidth product GBW VS= 5 V, G = 1 +25C 01 100 typical kHz Slew rate SR VS= 5 V, G = 1 +25C 01 0.03 typical V/s Overload
24、recovery time VINx G = VS+25C 01 100 typical s Output section Voltage output 4/ swing from rail RL= 100 k, AOL 70 dB +25C 01 3 typical mV RL= 25 k, AOL 90 dB 100 RL= 5 k, AOL 90 dB 500 RL= 25 k, AOL 82 dB -55C to +125C 100 RL= 5 k, AOL 89 dB 500 Short circuit current +25C 01 5 typical mA See footnot
25、es at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 7 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Co
26、nditions 2/Temperature, TA Device type Limits Unit Min Max Power supply section Specified voltage range VS+25C 01 2.3 5.5 V Minimum operating voltage +25C 01 2.1 typical V Quiescent current IQIO= 0 +25C 01 35 A (per amplifier) -55C to +125C 38 1/ Testing and other quality control techniques are used
27、 to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured
28、by characterization and/or design. 2/ Unless otherwise specified, VS= 2.3 V to 5.5 V, RL= 25 k connected to VS/ 2. 3/ The | symbols represent that the values and symbols are in parallel to each other. 4/ Output voltage swings are measured between the output and positive and negative power supply rai
29、ls. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 8 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking pe
30、rmitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 9 Case X Dimensions Symbol Inch Millimeters Min Max Min Max A - .057 - 1.45 A1 .000 .005 0.00 0.15 b .011 .019 0.30 0.50 c .003 .008 0.08 0.22 D .108 .120 2.75
31、 3.05 E .057 .068 1.45 1.75 E1 .102 .118 2.60 3.00 e .037 BSC 0.95 BSC L .011 .021 0.30 0.55 L1 .009 BSC 0.25 BSC n 5 leads 5 leads NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Body dimensions do not include mold flash or protrusion. Mold flash an
32、d protrusion shall not exceed 0.15 mm (0.006 inch) per side. 3. Falls with JEDEC MO-178-AA. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 D
33、WG NO. V62/06641 REV A PAGE 10 Device type 01 Case outline X Terminal number Terminal symbol 1 OUTPUT 2 -VS3 +INPUT 4 -INPUT 5 +VSFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS
34、, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06641 REV A PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of e
35、lectrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostati
36、c discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer rese
37、rves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the
38、 item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Top side marking Vendor part number V62/06641-01XE 01295 OAYM OPA336MDBVR
39、EP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Ln. PO Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
