1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKE
2、D BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, LINEAR, 24 V, LOW DROPOUT REGULATOR, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/08619 08-10-15 REV PAGE 1 OF 10 AMSC N/A 5962-V002-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
3、ense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 24 V low dropout regulator microcircuit, with an operating temperature range of -55C to
4、+125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/08619 - 01 X E Drawing Device type Case outline Lead
5、finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 TPS71501-EP 24 V low dropout regulator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 MO-203-AA Plastic su
6、rface mount 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or
7、 networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 3 1.3 Absolute maximum ratings. 1/ 2/ Input voltage range (VIN) -0.3 V to 24 V Output voltage range (VOUT) . -0.3 V to 6 V Peak output current Inte
8、rnally limited Continuous total power dissipation (PD) . See 1.5 dissipation rating table Junction temperature range (TJ) -55C to +150C Storage temperature range (TSTG) -65C to +150C Electrostatic discharge (ESD) rating: Human body model (HDM) . 2000 V Charge device model (CDM) 500 V 1.4 Recommended
9、 operating conditions. 3/ Operating free-air temperature range (TA) . -55C to +125C 1.5 Dissipation rating table. Board JCJADerating factor above TA 25C TA= 70C TA= 85C TA= 25C power rating power rating power rating Low K 4/ 165C/W 395C/W 2.52 mWC 250 mW 140 mW 100 mW High K 5/ 165C/W 315C/W 3.18 mW
10、/C 320 mW 175 mW 130 mW 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is
11、not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All voltage values are within respect to the network ground terminal. 3/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The man
12、ufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. 4/ The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the board. 5/ The JEDEC High K (2s2p) board design
13、 used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS
14、COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834
15、or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. T
16、he unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design,
17、 construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Bloc
18、k diagram. The block diagram shall be as shown in figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 5 TABLE I. Electrical performance charac
19、teristics. 1/ Limits Test Symbol Conditions 2/Temperature, TJDevice type Min Max Unit Input voltage 3/ VINIO= 10 mA -55C to +125C 01 2.5 24 V IO= 50 mA 3 24 Voltage range VOUT-55C to +125C 01 1.2 15 V VOUTaccuracy 3/ over VIN, IOUT, and temperature VOUTVIN+ 1.0 V VIN 24 V, 100 A IOUT 50 mA -55C to +
20、125C 01 -6.25 +6.25 % IGND0 mA IOUT 50 mA -40C to +85C 01 4.2 A Ground pin 4/ current 0 mA IOUT 50 mA -55C to +125C 4.8 0 mA IOUT 50 mA, VIN= 24 V 5.8 Load regulation VOUT/ IOUTIOUT= 100 A to 50 mA +25C 01 22 typical mV Output voltage 3/ line regulation VOUT/ VINVOUT+ 1 V VIN 24 V -55C to +125C 01 7
21、5 mV Output noise voltage VnBW = 200 Hz to 100 kHz, COUT= 10 F, IOUT= 50 mA +25C 01 575 typical Vrms Output current limit ICLVOUT= 0 V, VIN 3.5 V -55C to +125C 01 125 750 mA VOUT= 0 V, VIN 3.5 V 90 750 Power supply ripple rejection PSRR f = 100 kHz, COUT= 10 F +25C 01 60 typical dB Dropout voltage V
22、IN= VOUT(NOM)-1 V VDOIOUT= 50 mA -55C to +125C 01 750 mV 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all paramet
23、ers may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, VIN= VOUT(NOM)+ 1 V, IOUT= 1 mA, and COUT= 1 F. 3/ Minimum VIN= VOUT+ VDOor the value shown for input voltage in this tab
24、le, whichever is greater. 4/ See figure 3. This device employs a leakage null control circuit. This circuit is active only if output current is less than pass field effect transistor (FET) leakage current. The circuit is normally active when output load is less than 5 A, VINis greater than 18 V, and
25、 die temperature is greater than 100C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 6 Case X FIGURE 1. Case outline. Provided by IHSNot for Resal
26、eNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 7 Case X Dimensions Inches Millimeters Symbol Min Max Min Max A .031 .043 0.80 1.10 A1 .000 .003 0.00 0.10 b .005 .011 0.15 0.30
27、 c .003 .008 0.08 0.22 D .072 .084 1.85 2.15 E .043 .055 1.10 1.40 E1 .070 .094 1.80 2.40 e .025 BSC 0.65 BSC L .010 .018 0.26 0.46 L1 .005 BSC 0.15 BSC NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Body dimensions do not include mold flash or prot
28、rusion. Mold flash and protrusion shall not exceed 0.15 mm (0.005 inch) per side. 3. Falls within JEDEC MO-203-AA. FIGURE 1. Case outline - continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE
29、 A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 8 Device type 01 Case outline X Terminal number Terminal symbol Description 1 FB Feedback. This terminal is used to set the output voltage. 2 GND Ground. 3 NC No connection. 4 IN Input supply. 5 OUT Output of the regulator, any output capacitor 0.47
30、 F can be used for stability. FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE 9 Output voltage programming guide tab
31、le Output voltage R1 R2 1.8 V 0.499 M 1 M 2.8 V 1.33 M 1 M 5.0 V 3.16 M 1 M FIGURE 3. Block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08619 REV PAGE
32、 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and
33、labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are e
34、lectrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing wil
35、l be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ 2/
36、Device manufacturer CAGE code Package 3/ Top side marking Vendor part number V62/08619-01XE 01295 Reel of 3000 CVP TPS71501MDCKREP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ For the most current package and or
37、dering information, see the package option addendum at the end of the manufacturers data sheet , or use website . 3/ Package drawings, thermal data, and symbolization are available at CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
