1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD
2、CHECKED BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, LINEAR, LOW NOISE, VOLTAGE REFERENCE, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/08629 08-12-10 REV PAGE 1 OF 12 AMSC N/A 5962-V055-08 Provided by IHSNot for ResaleNo reproduction or networking permitted with
3、out license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance low noise voltage reference microcircuit, with an operating temperature range of
4、-55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/08629 - 01 X B Drawing Device type Case outli
5、ne Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Initial accuracy Circuit function 01 ISL21009BMB825EP 0.5 mV 2.5 V output, low noise voltage reference 02 ISL21009CMB825EP 1.0 mV 2.5 V output, low noise voltage reference 03 ISL21009BMB841EP 0.5 mV 4
6、.096 V output, low noise voltage reference 04 ISL21009BMB850EP 0.5 mV 5.0 V output, low noise voltage reference 05 ISL21009CMB850EP 1.0 mV 5.0 V output, low noise voltage reference 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package
7、style X 8 MS-012-AA Plastic surface mount 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNo
8、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Maximum voltage VINto GND -0.5 V to +18 V Maximum voltage VOUTto GND (10 seconds)
9、-0.5 V to VOUT+1 V Voltage on do not connect (DNC) pins . No connections permitted to these pins. Power dissipation (PD) . 471 mW 2/ Junction temperature range (TJ) +150C Storage temperature range (TSTG). -65C to +150C Thermal resistance, junction to ambient (JA) 120C/W Electrostatic discharge (ESD)
10、 rating: Human body model (HDM) . 6 kV Charge device model (CDM) 2 kV 1.4 Recommended operating conditions. 3/ Operating free-air temperature range (TA) -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings on
11、ly, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Derate 5.88 mW/C above+70C. JAis measured w
12、ith the component mounted on a high effective thermal conductivity test board in free air. See manufacturers technical brief TB379 for details. 3/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no
13、 responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 4 2. APPLICABLE DOCUMENTS JE
14、DEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legi
15、bly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if ap
16、plicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as sp
17、ecified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SU
18、PPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions IOUT= 0 mA, unless otherwise specifiedTemperature, TADevice type Min Max Unit VOUTaccuracy VOA+25C 01, 03, 04 -0.5 +0.5 mV 0
19、2,05 -1.0 +1.0 Output voltage temperature coefficient TC VOUT2/ -55C to +125C 01, 03, 04 3 ppm / C 02, 05 5 Supply current IIN-55C to +125C All 180 A 95 typical Trim range VOUT/ -55C to +125C All 2.0 % VOUT2.5 typical Short circuit current ISCVOUTtied to ground +25C All 10 typical mA Turn on settlin
20、g time tRVOUT= 0.1 % -55C to +125C All 100 typical s Ripple rejection f = 10 kHz -55C to +125C All 60 typical dB Output voltage noise eN0.1 Hz f 10 Hz -55C to +125C All 4.5 typical VP-PBroadband voltage noise VN10 Hz f 1 kHz -55C to +125C All 2.2 typical VRMSSee footnotes at end of table. Provided b
21、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions VIN= 5.0 V, IOUT
22、= 0 mA, unless otherwise specifiedTemperature, TA Device type Min Max Unit Output voltage VOUT-55C to +125C 01, 02 2.500 typical V Input voltage range VIN-55C to +125C 01, 02 3.5 16.5 V Line regulation VOUT/ 3.5 V VIN 5.5 V -55C to +125C 01, 02 150 V / V VIN50 typical 5.5 V VIN 16.5 V 50 10 typical
23、Load regulation VOUT/ Sourcing, 0 mA IOUT 7 mA -55C to +125C 01, 02 50 V / IOUT10 typical mA Sinking, -7 mA IOUT 0 mA 100 20 typical Thermal hysteresis VOUT/ TA3/ TA= +165C 01, 02 50 typical ppm Long term stability VOUT/ t 4/ +25C 01, 02 50 typical ppm See footnotes at end of table. Provided by IHSN
24、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 7 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions VIN= 5.0 V, IOUT= 0 mA
25、, unless otherwise specifiedTemperature, TA Device type Min Max Unit Output voltage VOUT-55C to +125C 03 4.096 typical V Input voltage range VIN-55C to +125C 03 4.5 16.5 V Line regulation VOUT/ 4.5 V VIN 16.5 V -55C to +125C 03 200 V / V VIN50 typical Load regulation VOUT/ Sourcing, 0 mA IOUT 5 mA -
26、55C to +125C 03 100 V / IOUT20 typical mA Sinking, -5 mA IOUT 0 mA 150 20 typical Thermal hysteresis VOUT/ TA3/ TA= +165C 03 50 typical ppm Long term stability VOUT/ t 4/ +25C 03 50 typical ppm See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted withou
27、t license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 8 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions VIN= 10.0 V, IOUT= 0 mA, unless otherwise specifiedTemperature, TA Device type Mi
28、n Max Unit Output voltage VOUT-55C to +125C 04, 05 5.000 typical V Input voltage range VIN-55C to +125C 04, 05 5.5 16.5 V Line regulation VOUT/ 5.5 V VIN 16.5 V -55C to +125C 04, 05 90 V / V VIN20 typical Load regulation VOUT/ Sourcing, 0 mA IOUT 7 mA -55C to +125C 04, 05 100 V / IOUT10 typical mA S
29、inking, -7 mA IOUT 0 mA 150 20 typical Thermal hysteresis VOUT/ TA3/ TA= +165C 04, 05 50 typical ppm Long term stability VOUT/ t 4/ +25C 04, 05 50 typical ppm 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temp
30、erature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Over the specified temperature range. Temperatu
31、re coefficient is measured by the box method whereby the change in VOUTis divided by the temperature range; in this case, -55C to +125C = +180C. 3/ Thermal hysteresis is the change VOUTmeasured at TA= +25C after temperature cycling over a specified range, TA. VOUTis read initially at TA= +25C for th
32、e device under test. The device is temperature cycled and a second VOUTmeasurement is taken at +25C. The difference between the initial VOUTreading and the second VOUTreading is then expressed in ppm. For TA= +180C, the device under test is cycled from +25C to +125C to -55C to +25C. 4/ Long term dri
33、ft is logarithmic in nature and diminishes over time. Drift after the first 1,000 hours will be approximately 10 ppm / hours 1,000 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO.
34、16236 DWG NO. V62/08629 REV PAGE 9 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 10 Case X continued. Dimensions In
35、ches Millimeters Notes Symbol Min Max Min Max A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - b 0.013 0.020 0.33 0.51 9 c 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 4 E 0.1497 0.1574 3.80 4.00 5 E1 0.2284 0.2440 5.80 6.20 - e 0.050 BSC 1.27 BSC - L 0.016 0.050 0.40 1.27 7 n 8 8 8 N
36、OTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Symbols are defined in the “MO series symbol list” in section 2.2 of JEDEC publication number 95. 3. Dimensioning and tolerance per ANSI Y14.5M-1982. 4. Dimension “D” does not include mold flash, protrus
37、ions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15 mm (0.006 inch) per side. 5. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25 mm (0.010 inch) per side. 6. The chamfer on the body is optional. If it is
38、 not present, a visual index feature must be located within the crosshatched area. 7. “L” is the length of terminal for soldering to a substrate. 8. “n” is the number of terminal positions. 9. The lead width “b”, as measured 0.36 mm (0.014 inch) or greater above the seating plane, shall not exceed a
39、 maximum value of 0.61 mm (0.024 inch). 10. Falls within JEDEC MS-012-AA. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 R
40、EV PAGE 11 Device types All Case outline X Terminal number Terminal symbol 1 GND or NC 2 VIN3 DNC 4 GND 5 TRIM or NC 6 VOUT7 DNC 8 DNC Terminal symbol Description GND or NC Can be either ground or no connect. VINPower supply input connection. GND Ground connection. TRIM Allows user trim typically 2.
41、5%. Leave unconnected when unused. VOUTVoltage reference output connection. DNC Do not connect; internal connection must be left floating. FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS
42、 COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08629 REV PAGE 12 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handli
43、ng of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for elect
44、rostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufactur
45、er reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply
46、for the item. Vendor item drawing administrative control number 1/ 2/ Device manufacturer CAGE code Grade Part marking Vendor part number V62/08629-01XB 34371 0.5 mV, 3 ppm/C 21009BM25EP ISL21009BMB825EP V62/08629-02XB 34371 1.0 mV, 5 ppm/C 21009CM25EP ISL21009CMB825EP V62/08629-03XB 34371 0.5 mV, 3
47、 ppm/C 21009BM41EP ISL21009BMB841EP V62/08629-04XB 34371 0.5 mV, 3 ppm/C 21009BM50EP ISL21009BMB850EP V62/08629-05XB 34371 1.0 mV, 5 ppm/C 21009CM50EP ISL21009CMB850EP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ Add “-TK” suffix for tape and reel. Please refer to manufacturers technical brief TB347 for details on reel specifications. CAGE code Source of supply 34371 Intersil Corpor
