1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY RAJESH PITHADIA DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHE
2、CKED BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, LINEAR, QUAD, PRECISION, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/09614 08-12-18 REV PAGE 1 OF 10 AMSC N/A 5962-V021-09 Provided by IHSNot for ResaleNo reproduction or networking permitt
3、ed without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance quad, precision, operational amplifier microcircuit, with an operating tem
4、perature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/09614 - 01 X E Drawing Devi
5、ce type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 LT1014 Quad, precision, operational amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Packa
6、ge style X 16 MS-013-AA Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by I
7、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -22 V to 22 V 2/ Differential input voltage range .
8、 -30 V to 30 V 3/ Input voltage range (any input) . -VCC 5 V to +VCC2/ Duration of short-circuit current Unlimited 4/ Continuous total power dissipation (PD) . See dissipation rating table Storage temperature range (TSTG). -65C to 150C Lead temperature (1.6 mm, at distance 1/16 inch from case for 10
9、 seconds) 260C 1.4 Recommended operating conditions. 5/ Operating free-air temperature range (TA) -55C to +125C Dissipation rating table Package TA 25C Derating factor TA= 70C TA= 105C TA= 125C power rating above TA= 25C power rating power rating power rating X 1025 mW 8.2 mW/C 656 mW 369 mW 205 mW
10、1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to
11、 absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All voltage values, except differential voltages, are with respect to the midpoint between +VCCand VCC. 3/ Differential voltages are at the noninverting input with respect to the inverting input. 4/ The output
12、may be shorted to either supply. 5/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reprodu
13、ction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addres
14、sed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAG
15、E code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrica
16、l performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline(s). The case outline(s) shall be as shown in 1.2.2 and figure
17、1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 5 TABLE I. El
18、ectrical performance characteristics. 1/ Limits Test Symbol Conditions 2/Temperature, TA Device type Min Max Unit Input offset voltage VIORS= 50 +25C 01 450 V -55C to +125C 1500 RS= 50 , VIC= 0.1 V +125C 750 Input offset current IIO+25C 01 2 nA -55C to +125C 10 Input bias current IIB+25C 01 -50 nA -
19、55C to +125C -120 Common-mode input voltage range VICR+25C 01 0 to 3.5 V -55C to +125C 0.1 to 3 Maximum peak output voltage swing VOMOutput low, no load +25C 01 25 mV Output low, RL= 600 to GND +25C 10 -55C to +125C 18 Output low, ISINK= 1 mA +25C 350 Output high, no load +25C 4 V Output high +25C 3
20、.4 RL= 600 to GND -55C to +125C 3.1 Large signal differential voltage amplification AVDVO= 5 mV to 4 V, RL= 500 +25C 01 1 typical V/V Supply current per amplifier ICC+25C 01 0.5 mA -55C to +125C 0.65 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted
21、without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 6 HzHzTABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions 3/Temperature, TA Device type Min Max Unit Slew rate SR +25C 01 0.2 V/s
22、 Equivalent input noise voltage Vnf = 10 Hz +25C 01 24 typical nV/ f = 1 kHz 22 typical Peak-to-peak equivalent input noise voltage VN(PP)f = 0.1 Hz to 10 Hz +25C 01 0.55 typical V Equivalent input noise current Inf = 10 Hz +25C 01 0.07 typical pA/ 1/ Testing and other quality control techniques are
23、 used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is ass
24、ured by characterization and/or design. 2/ Unless otherwise specified, +VCC= 5 V, -VCC= 0 V, VO= 1.4 V, VIC= 0 V. 3/ Unless otherwise specified, VCC=15 V, VIC= 0 V.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMB
25、US, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 7 Case X FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 8
26、Case X continued. Dimensions Inches Millimeters Symbol Min Max Min Max A - 0.104 - 2.65 A1 0.004 0.012 0.10 0.30 b 0.012 0.020 0.31 0.50 c 0.008 0.013 0.20 0.33 D 0.398 0.413 10.10 10.50 E 0.291 0.299 7.40 7.60 E1 0.393 0.419 9.97 10.63 e 0.050 NOM 1.27 NOM L 0.016 0.050 0.40 1.27 n 16 16 NOTES: 1.
27、Controlling dimensions are inch, millimeter dimensions are given for reference only. 2. Body length does not include mold flash, protrusion, or gate burrs. Mold flash, protrusion, or gate burrs shall not exceed 0.006 inch (0.15 mm) per end. 3. Falls within reference to JEDEC MS-013-AA. FIGURE 1. Cas
28、e outlines continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09614 REV PAGE 9 Device type 01 Case outlines X Terminal number Terminal symbol 1 1OUT 2 1IN-
29、 3 1IN+ 4 +VCC5 2IN+6 2IN- 7 2OUT 8 NC 9 NC 10 3OUT 11 3IN- 12 3IN+ 13 -VCC/GND 14 4IN+ 15 4IN- 16 4OUT FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT N
30、O. 16236 DWG NO. V62/09614 REV PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devic
31、es, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive device
32、s. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make chang
33、es without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing a
34、dministrative control number 1/ Device manufacturer CAGE code Vendor part number V62/09614-01XE 01295 LT1014DMDWREP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
