1、 REVISIONSLTR DESCRIPTION DATE APPROVEDA Delete the -55C to +125C temperature limit from the Initial accuracy test under Table I. Output voltage temperature drift test, for device types 01, 02, change the maximum limit from 5 ppm/C to 6.5 ppm/C under Table I. - ro 10-08-19 C. SAFFLE B Add device typ
2、e 04. - ro 10-11-17 C. SAFFLE CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED
3、 BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA TITLE MICROCIRCUIT, LINEAR, LOW NOISE, LOW DRIFT, PRECISION VOLTAGE REFERENCE, MONOLITHIC SILICON 10-05-11 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236
4、 DWG NO. V62/10613 REV B PAGE 1 OF 9 AMSC N/A 5962-V012-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10613 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing docu
5、ments the general requirements of a low noise, low drift, precision voltage reference microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an
6、 administrative control number for identifying the item on the engineering documentation: V62/10613 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Output voltage Circuit function 01 REF5020 2.048 V Low noise,
7、 low drift, precision voltage reference 02 REF5040 4.096 V Low noise, low drift, precision voltage reference 03 REF5050 5.0 V Low noise, low drift, precision voltage reference 04 REF5025 2.5 V Low noise, low drift, precision voltage reference 1.2.2 Case outline(s). The case outline(s) are as specifi
8、ed herein. Outline letter Number of pins JEDEC PUB 95 Package style X 8 MS-012-AA Plastic surface mount with gullwing leads 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-le
9、ad plateC Gold plateD PalladiumE Gold flash palladium Z Other 1.3 Absolute maximum ratings. 1/ Input voltage (VIN) 18 V Output short circuit (IOS) 30 mA Operating temperature range (TA) . -55C to +125C Storage temperature range (TSTG) -65C to +150C Junction temperature range (TJmax) 150C Power dissi
10、pation (PD) . 166.66 mW Electrostatic discharge (ESD) rating: Human body model (HBM) . 3,000 V Charged device model (CDM) 1,000 V _ 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the
11、 device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
12、nse from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10613 REV B PAGE 3 1.4 Recommended operating conditions. 2/ Input voltage range (VIN) per device ( VOUT+ 0.2 V ) to 18 V Operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS JE
13、DEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legi
14、bly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if ap
15、plicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as sp
16、ecified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 2/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk.
17、 The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO.
18、 V62/10613 REV B PAGE 4 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/ Temperature, TADevice type Limits Unit Min Max Output voltage VOUT2.7 V VIN 18 V 3/ +25C 01 2.048 typical V 02 4.096 typical03 5 typical 04 2.5 typicalInitial accuracy +25C All -0.05 0.05 % Output v
19、oltage noise f = 0.1 Hz to 10 Hz +25C 01 6 typical VPP02 12 typical03 15 typical 04 7.5 typicalOutput voltage temperature drift VOUT/ T -55C to +125C 01, 02 5 ppm / C 03, 04 6.5Line regulation VOUT/ VINVIN= 2.7 V to 18 V 3/ +25C 01 1 ppm/V VIN= VOUT+ 0.2 V +25C 02, 03, 04 1 -55C to +125C 3 Load regu
20、lation VOUT/ ILOAD-10 mA ILOAD +10 mA, VIN= 3 V +25C 01 30 ppm / mA -10 mA ILOAD +10 mA, +25C 02, 03, 04 30 VIN= VOUT+ 0.75 V -55C to +125C 60 Short circuit current ISCVOUT= 0 V +25C All 25 typical mA TEMP pin, voltage output +25C All 575 typical mV TEMP pin, temperature sensitivity -55C to +125C Al
21、l 2.64 typical mV/C Turn on settling time To 0.1 % with CL= 1 F +25C All 200 typical s See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V
22、62/10613 REV B PAGE 5 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/ Temperature, TADevice type Limits Unit Min Max Supply voltage VS3/ +25C All VOUT+ 0.2 18 V Quiescent current +25C All 1 mA -55C to +125C 1.25 Specified temperature range All -55 +125 C Opera
23、ting temperature range All -55 +125 C Thermal resistance, junction to ambient JAAll 150 typical C/W 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across
24、 the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, ILOAD= 0, CL= 1 F, and VIN= ( VOUT+ 0.2 V ) to 18 V. 3/ For VOUT 2.5 V, the mi
25、nimum supply voltage is 2.7 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10613 REV B PAGE 6 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo re
26、production or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10613 REV B PAGE 7 Case X Symbol Dimensions Inches Millimeters Min Max Min Max A - 0.069 - 1.75 A1 0.004 0.010 0.10 0.25 b 0.012 0.020 0.31 0.51 c 0.
27、007 0.010 0.17 0.25 D 0.189 0.197 4.80 5.00 E 0.150 0.157 3.80 4.00 E1 0.228 0.244 5.80 6.20 e 0.050 BSC 1.27 BSC L 0.016 0.050 0.40 1.27 n 8 8 NOTES: 1. Controlling dimensions are inch, millimeter dimensions are given for reference only. 2. For dimension D, body length does not include mold flash,
28、protrusion, or gate burrs. Mold flash, protrusion, or gate burrs shall not exceed 0.006 inch (0.15 mm) per end. 3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm) per side. 4. Falls with JEDEC MS-012-AA. FIGURE 1. Case outline Conti
29、nued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10613 REV B PAGE 8 Device types 01, 02, 03, 04 Case outline X Terminal number Terminal symbol Description 1 D
30、NC Do not connect 2 VINInput voltage 3 TEMP Temperature output terminal 4 GND Ground 5 TRIM / NR Trim and noise reduction 6 VOUTOutput voltage 7 NC No internal connection 8 DNC Do not connect FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without
31、 license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10613 REV B PAGE 9 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal docum
32、entation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the
33、 manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the
34、 device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of pr
35、esent or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ 2/ 3/ Device manufacturer CAGE code Output voltage Top side marking Vendor part number V62/10613-01XE 01295 2.048 V 5020EP REF5020MDREP V62/10613-02XE 01295 4.096 V 5040EP REF5040
36、MDREP V62/10613-03XE 01295 5 V 5050EP REF5050MDREP V62/10613-04XE 01295 2.5 V 5025EP REF5025MDTEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ For the most current package and ordering information, see the packa
37、ge option addendum at the end of the manufacturers data sheet. 3/ Package drawings, standard packaging quantities, thermal data, symbolization, and printed circuit board (PCB) design guidelines are available from the manufacturer. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group8505 Forest lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
