1、 REVISIONSLTR DESCRIPTION DATE APPROVEDPrepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY RAJ
2、ESH PITHADIA TITLE MICROCIRCUIT, LINEAR, DUAL, HIGH SPEED BiFET OPERATIONAL AMPLIFIER, MONOLITHIC SILICON 10-12-13 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/11603 REV PAGE 1 OF 11 AMSC N/A 5962-V011-11 Provided by IHSNot for ResaleNo reproduction or networking permitted
3、without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance dual, high speed bipolar field effect transistor (BiFET) operational amplifier microcir
4、cuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/
5、11603 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 AD712-EP Dual, high speed BiFET operational amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline lette
6、r Number of pins JEDEC PUB 95 Package style X 8 MS-012-AA Plastic small outline1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plateC Gold plateD PalladiumE Gold flash p
7、alladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) 18 V Input voltage (VIN) 18 V 2/ Outpu
8、t short circuit duration . Indefinite Differential input voltage . +VSand -VSPower dissipation(PD) 14.4 mW Junction temperature range (TJ) -65C to +150C Storage temperature range (TSTG) -65C to +125C Lead temperature range (soldering, 60 seconds) . +300C Thermal resistance, junction to ambient (JC)
9、43C/W Thermal resistance, junction to ambient (JA) 100C/W 1.4 Recommended operating conditions. 3/ Supply voltage (VS) 15 V Operating temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress rati
10、ngs only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ For supply voltages less than 18 V, t
11、he absolute maximum voltage is equal to the supply voltage. 3/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by
12、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies
13、 should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufa
14、cturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditi
15、ons and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2
16、and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 5 TABLE I. E
17、lectrical performance characteristics. 1/ Test Symbol Conditions VS= 15 V unless otherwise specifiedTemperature, TADevice type Limits Unit Min Max Input offset voltage section 2/ Initial offset voltage VIO+25C 01 3 mV -55C to +125C 4 Initial offset voltage versus temperature VIO/ T +25C 01 20 V/C In
18、itial offset voltage versus supply VIO/ +25C 01 76 dB VS-55C to +125C 76 Long term offset stability +25C 01 15 typical V/ month Input bias current 3/ IIBVCM= 0 V +25C 01 75 pA +125C 77 nA VCM= 10 V +25C 100 pA Input offset current IIOVCM= 0 V +25C 01 25 pA +125C 26 nA Matching characteristics sectio
19、n Input offset voltage VIO+25C 01 3 mV -55C to +125C 4 Input offset voltage drift +25C 01 20 V/C Input bias current IIB+25C 01 25 pA Crosstalk At f = 1 kHz +25C 01 120 typical dB At f = 100 kHz 90 typical See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permi
20、tted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VS= 15 V unless otherwise specifiedTemperature, TADevice type Limits Unit Min Max Frequ
21、ency response section Small signal bandwidth SSBW +25C 01 3.0 MHz Full power response FPR +25C 01 200 typical kHz Slew rate SR +25C 01 16 V/s Settling time to 0.01% tS+25C 01 1.2 s Total harmonic distortion THD +25C 01 0.0003 typical % Input impedance section Differential input impedance 4/ +25C 01
22、3 x 1012| 5.5 typical |pF Common mode input impedance 4/ +25C 01 3 x 1012| 5.5 typical |pF Input voltage range section Differential input 5/ voltage range VDIN+25C 01 20 typical V Common mode 6/ voltage VCM+25C 01 +14.5, -11.5 typical V -55C to +125C -VS+ 4 +VS- 2 Common mode rejection ratio CMRR VC
23、M= 10 V +25C 01 76 dB -55C to +125C 76 VCM= 11 V +25C 70 -55C to +125C 70 Input voltage noise section Input voltage noise 0.1 Hz to 10 Hz +25C 01 2 typical Vp-p f = 10 Hz 45 typical nV / Hz f = 100 Hz 22 typical f = 1 kHz 18 typical f = 10 kHz 16 typical See footnotes at end of table. Provided by IH
24、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 7 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VS= 15 V unless otherwise specifiedTe
25、mperature, TADevice type Limits Unit Min Max Input current noise NI f = 1 kHz +25C 01 0.01 typical pA / Hz Open loop gain AOL +25C 01 150 V/mV -55C to +125C 100 Output characteristics Output voltage swing high VOH+25C 01 13.0 V -55C to +125C 12.0 Output voltage swing low VOL+25C 01 -12.5 V -55C to +
26、125C -12.0 Output current IOUT+25C 01 25 typical mA Power supply section Rated performance +25C 01 15 typical V Operating range +25C 01 4.5 18 V Quiescent current +25C 01 6.8 mA 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
27、 the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Input offset voltage specifi
28、cations are guaranteed after 5 minutes of operation at TA= +25C. 3/ Bias current specifications are guaranteed maximum at either input after five minutes of operation at TA= +25C. For higher temperatures, the current doubles every 10C. 4/ The | symbolizes that the input impedance is being represente
29、d as the resistance value is in parallel with the capacitance. 5/ Defined as voltage between inputs, such that neither exceeds 10 V from ground. 6/ Typically exceeding -14.1 V negative common mode voltage on either input results in an output phase reversal. Provided by IHSNot for ResaleNo reproducti
30、on or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 8 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME
31、 COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 9 Case X Symbol Dimensions Inches Millimeters Min Max Min Max A 0.0532 0.0688 1.35 1.75 A1 0.0040 0.0098 0.10 0.25 b 0.0122 0.0201 0.31 0.51 c 0.0067 0.0098 0.17 0.25 D 0.1890 0.1968 4.80 5.00 E 0.1497 0.1574 3.80 4.00 E1 0.2284
32、0.2441 5.80 6.20 e 0.0500 BSC 1.27 BSC L 0.0157 0.0500 0.40 1.27 n 8 8 NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only and are not appropriate for use in design. 2. Body dimensions do not include mold flash or protrusion not to exceed 0.006 inch (0.15 mm
33、). 3. Falls with JEDEC MS-012-AA. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 10 Device type 01 Case outline X Terminal
34、number Terminal symbol 1 OUTPUT 1 2 INVERTING INPUT 1 3 NONINVERTING INPUT 1 4 -VS5 NONINVERTING INPUT 2 6 INVERTING INPUT 2 7 OUTPUT 2 8 +VSFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBU
35、S, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11603 REV PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of el
36、ectrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic
37、 discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reser
38、ves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the
39、item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number V62/11603-01XE 24355 AD712TRZ-EP-R7 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 24355 Analog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: Raheen Business Park Limerick, Ireland Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
