1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ Original
2、 date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA TITLE MICROCIRCUIT, LINEAR, SINGLE SUPPLY, QUAD, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON 12-09-05 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/12634 REV PAGE 1 OF 12 AMSC N/A 5962-V094-12 Provided by IHSNot for ResaleNo
3、 reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance single supply quad operational amplifier microcir
4、cuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/
5、12634 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 AD8574 Zero drift, single supply, quad operational amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outlin
6、e letter Number of pins JEDEC PUB 95 Package style X 14 MO-153-AB-1 Plastic thin shrink small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate
7、 D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VS) 6 V I
8、nput voltage . GND to VS+ 0.3 V Differential input voltage . 5.0 V 2/ Power dissipation (PD) . 138.8 mW typical Output short circuit duration to GND Indefinite Storage temperature range (TSTG) -65C to +150C Junction temperature range (TJ) -65C to +150C Lead temperature (soldering, 60 seconds) . +300
9、C Thermal resistance, junction to case (JC) . 36C/W Thermal resistance, junction to ambient (JA) 180C/W Electrostatic discharge: Human body model (HBM) . 2000 V 1.4 Recommended operating conditions. 3/ Supply voltage range (VS) 5 V Operating free-air temperature range (TA) -55C to +125C 1/ Stresses
10、beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-ma
11、ximum-rated conditions for extended periods may affect device reliability. 2/ Differential input voltage is limited to 5.0 V or the supply voltage, whichever is less. 3/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or
12、distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 4 2. APPLICABLE
13、 DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permane
14、ntly and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A
15、 and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensi
16、ons are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
17、DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VS= 5 V, VCM= 2.5 , VO= 2.5 V unless otherwise specifiedTemperature, TA Device type Limits Unit Min Max Input characteristics. O
18、ffset voltage VOS+25C 01 5 V -55C to +125C 15 Input bias current IB+25C 01 50 pA -55C to +125C 1.5 nA Input offset current IOS+25C 01 70 pA -55C to +125C 200 Input voltage range VIN+25C 01 0 5 V Common mode rejection ratio CMRR VCM= 0 V to 5 V +25C 01 120 dB -55C to +125C 115 Large signal voltage 2/
19、 gain AVOVO= 0.3 V to 4.7 V, RL= 10 k +25C 01 125 dB -55C to +125C 120 Offset voltage drift VOS/ T -55C to +125C 01 0.04 V/C Output characteristics. Output voltage high VOHRL= 100 k to GND +25C 01 4.99 V -55C to +125C 4.99 RL= 10 k to GND +25C 4.95 -55C to +125C 4.95 Output voltage low VOLRL= 100 k
20、to +VS+25C 01 10 mV -55C to +125C 10 RL= 10 k to +VS+25C 30 -55C to +125C 30 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 6
21、TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VS= 5 V, VCM= 2.5 , VO= 2.5 V unless otherwise specifiedTemperature, TA Device type Limits Unit Min Max Output characteristics continued. Short circuit limit ISC+25C 01 25 mA -55C to +125C 40 typical Output current
22、IO+25C 01 30 typical mA -55C to +125C 15 typical Power supply. Power supply rejection ratio PSRR VS= 2.7 V to 5.5 V +25C 01 120 dB -55C to +125C 115 Supply current per amplifier ISYVO= 0 V +25C 01 975 A -55C to +125C 1075 Dynamic performance. Slew rate SR RL= 10 k +25C 01 0.4 typical V/s Overload re
23、covery time +25C 01 0.3 ms Gain bandwidth product GBP +25C 01 1.5 typical MHz Noise performance. Voltage noise enp-p 0 Hz to 10 Hz +25C 01 1.3 typical Vpp 0 Hz to 1 Hz 0.41 typical Voltage noise density enf = 1 kHz +25C 01 51 typical nV / Hz Current noise density inf = 10 Hz +25C 01 2 typical fA / H
24、z See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 7 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol C
25、onditions VS= 2.7 V, VCM= 1.35 V, VO= 1.35 V unless otherwise specifiedTemperature, TA Device type Limits Unit Min Max Input characteristics. Offset voltage VOS+25C 01 5 V -55C to +125C 15 Input bias current IB+25C 01 50 pA -55C to +125C 1.5 nA Input offset current IOS+25C 01 50 pA -55C to +125C 200
26、 Input voltage range VIN+25C 01 0 2.7 V Common mode rejection ratio CMRR VCM= 0 V to 2.7 V +25C 01 115 dB -55C to +125C 110 Large signal voltage 2/ gain AVOVO= 0.3 V to 2.4 V, RL= 10 k +25C 01 110 dB -55C to +125C 105 Offset voltage drift VOS/ T -55C to +125C 01 0.04 V/C Output characteristics. Outp
27、ut voltage high VOHRL= 100 k to GND +25C 01 2.685 V -55C to +125C 2.685 RL= 10 k to GND +25C 2.67 -55C to +125C 2.67 Output voltage low VOLRL= 100 k to +VS+25C 01 10 mV -55C to +125C 10 RL= 10 k to +VS+25C 20 -55C to +125C 20 See footnotes at end of table. Provided by IHSNot for ResaleNo reproductio
28、n or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 8 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VS= 2.7 V, VCM= 1.35 V, VO= 1.35 V unless otherwise specifiedTempe
29、rature, TA Device type Limits Unit Min Max Output characteristics continued. Short circuit limit ISC+25C 01 10 mA -55C to +125C 10 typical Output current IO+25C 01 10 typical mA -55C to +125C 5 typical Power supply. Power supply rejection ratio PSRR VS= 2.7 V to 5.5 V +25C 01 120 dB -55C to +125C 11
30、5 Supply current per amplifier ISYVO= 0 V +25C 01 900 A -55C to +125C 1000 Dynamic performance. Slew rate SR RL= 10 k +25C 01 0.5 typical V/s Overload recovery time +25C 01 0.05 typical ms Gain bandwidth product GBP +25C 01 1.0 typical MHz Noise performance. Voltage noise enp-p 0 Hz to 10 Hz +25C 01
31、 2.0 typical Vpp Voltage noise density enf = 1 kHz +25C 01 94 typical nV / Hz Current noise density inf = 10 Hz +25C 01 2 typical fA / Hz 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Produc
32、t may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Gain testing is dependent upon test bandwidth. Provided by IHSNot fo
33、r ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 9 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
34、DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 10 Case X Symbol Dimensions Inches Millimeters Min Max Min Max A - .047 - 1.20 A1 .001 .005 0.05 0.15 A2 .031 .041 0.80 1.05 b .007 .011 0.19 0.30 c .003 .007 0.09 0.20 D .192 .200 4.90 5.10 E .169 .177 4.30
35、4.50 E1 .251 BSC 6.40 BSC e .025 BSC 0.65 BSC L .017 .028 0.45 0.75 NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Falls within reference to JEDEC MO-153-AB-1. FIGURE 1. Case outline - Continued. Provided by IHSNot for ResaleNo reproduction or netwo
36、rking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 11 Device type 01 Case outline X Terminal number Terminal symbol 1 OUTPUT A 2 -INPUT A 3 +INPUT A 4 +VS5 +INPUT B 6 -INPUT B 7 OUTPUT B 8 OUTPUT C 9 -INPUT C 10 +I
37、NPUT C 11 -VS12 +INPUT D 13 -INPUT D 14 OUTPUT D FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12634 REV PAGE 12 4. VERIFICATION 4.1 Produc
38、t assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive
39、 devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensiti
40、ve and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are p
41、rovided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at
42、 http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Transport media, quantity Vendor part number V62/12634-01XE 24355 Reel, 2500 AD8574TRU-EP-RL Tube, 96 AD8574TRU-EP 1/ The vendor item drawing establishes an administr
43、ative control number for identifying the item on the engineering documentation. CAGE code Source of supply 24355 Analog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: Raheen Business Park Limerick, Ireland Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
