1、AMSC N/A FSC 6145 INCH-POUND MIL-DTL-17/135D 03 June 2013 SUPERSEDING MIL-C-17/135C 13 April 1993 DETAIL SPECIFICATION SHEET CABLE, RADIO FREQUENCY, TRIAXIAL, .500 INCH, 50 OHM, WATER BLOCKED, NON-WATER BLOCKED AND CROSSLINKED, LOW SMOKE This specification is approved for use by all Departments and
2、Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-17. NOTE: Cable should be constructed of non-toxic material. FIGURE 1. General configuration. Provided by IHSNot for ResaleNo reproduction or netwo
3、rking permitted without license from IHS-,-,-MIL-DTL-17/135D 2 TABLE I. Description. Component Construction Inner conductor (M17/135-00001 and -00002) Seven strands of silver-coated copper wire each strand .0296 inch diameter. Diameter: .089 inch 0.001 Inner conductor(M17/135-00003 thru -00006) Soli
4、d silver-coated copper wire diameter. Diameter: .081 inch 0.001 Dielectric core Type A-1: Solid polyethylene Diameter: .285 inch 0.010 Inner shield Single braid of AWG No. 33 silver-coated copper wire Diameter: .340 inch maximum Coverage: 90%, minimum Carriers: 24 Ends: 7 Picks/inch: 8 Separator tap
5、e optional Interlayer (M17/135-00001 thru M17/135-00004) Type A-1: Solid polyethylene Diameter: .365 inch .010 Interlayer (M17/135-00005 and M17/135-00006) Cross-linked polyolefin Diameter: .365 inch .010 Outer shield Single braid of AWG No. 33 silver-coated copper wire Diameter: .414 inch, maximum
6、Coverage: 85%, minimum Carriers: 24 Ends: 8 Picks/inch: 5.11 Separator tape optional Jacket M17/135-00005 1/ and M17/135-00006 Cross-linked polyolefin Diameter: .500 inch .010, maximum Jacket M17/135-00001 1/ and M17/135-00002 Type XIII: Polyurthane Diameter: .500 inch .010, maximum Jacket M17/135-0
7、0003 1/ and M17/135-00004 Type IIIa: Polyethylene Diameter: .500 inch .010 1/ Free strippable blocking compound needed where necessary to meet hydrostatic test. The inner shield may be partially imbedded in the dielectric. Applicable to water blocked cables only. ENGINEERING INFORMATION Continuous w
8、orking voltage: 3,700 V rms, maximum. Operating frequency: 3 GHz, maximum. Velocity of propagation: 65.9 percent, nominal. Power rating: See figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17/135D 3 Operating temperature range: -40C
9、 to +70C (M17/135-00001 thru M17/135-00004) -30C to +85C (M17/135-00005 and M17/135-00006) Inner conductor properties: DC resistance (maximum at 20C): 1.62 ohms per 100 feet. (0.173 ohm per 100 feet for M17/135-00001 and M17/135-00002.) Elongation: 25 percent, minimum. (30 percent minimum for M17/13
10、5-00001 and M17/135-00002) Tensile strength: Not applicable. Engineering note: This cable useful for non-hosing low temperature applications. REQUIREMENTS Dimensions, configuration, and description: See figure 1 and table I. Environmental and mechanical: Visual and mechanical examination: Out-of-rou
11、ndness: Not applicable. Eccentricity: 10 percent, maximum. Adhesion of conductors: M17/135-00001,M17/135-00003,and M17/135-00005: 7 pounds minimum, 65 pounds maximum. M17/135-00002,M17/135-00004,and M17/135-00006: 7 pounds minimum, 50 pounds maximum Aging stability: +90C 2C (M17/135-00003 and M17/13
12、5-00004) +98C 2C (M17/135-00001, M17/135-00002, M17/135-00005 and M17/135-00006) Stress crack resistance: Not applicable. Outer conductor integrity: Not applicable. Cold bend: -55C 2C (M17/135-00001 thru M17/135-00004) -30C 2C (M17/135-00005 and M17/135-00006) Dimensional stability: +85C 2C. Inner c
13、onductor from core: .125 inch, maximum. Inner conductor from jacket: .250 inch, maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17/135D 4 Contamination: Not applicable. Bendability: Not applicable. Flammability: Not applicable. Flame
14、 propagation: Applicable to M17/135-00005 and M17/135-00006. Acid gas generation: 2.0 percent, maximum. Halogen content: 0.2 percent, maximum. Applicable to M17/135-00005 and M17/135-00006. Immersion test: Applicable to M17/135-00005 and M17/135-00006. Tensile strength, percent of unaged minimum: 50
15、 Applicable to M17/135-00005 and M17/135-00006. Elongation, percent of unaged minimum: 50. Applicable to M17/135-00005 and M17/135-00006. Smoke index: 25 maximum. Applicable to M17/135-00005 and M17/135-00006. Toxicity index: 5 maximum. Applicable to M17/135-00005 and M17/135-00006. Durometer hardn
16、ess: (type A) 80 minimum. Applicable to M17/135-00005 and M17/135-00006. Weathering: Applicable to M17/135-00005 and M17/135-00006. Abrasion resistance: 75 cycles minimum (jacket only). Applicable to M17/135-00005 and M17/135-00006. Tear strength: 35 pounds per inch minimum. Applicable to M17/135-00
17、005 and M17/135-00006. Heat distortion: 30 percent maximum distortion. Applicable to M17/135-00005 and M17/135-00006. Physical tests on unaged jacket: Tensile strength: 1,300 psi, minimum. Applicable to M17/135-00005 and M17/135-00006. Elongation: 160 percent, minimum. Applicable to M17/135-00005 an
18、d M17/135-00006. Physical tests on aged jacket: Applicable to M17/135-00005 and M17/135-00006. Air oven: Tensile strength, percent minimum: 60. Elongation, percent minimum: 60. Hot oil immersion: Applicable to M17/135-00005 and M17/135-00006. Tensile strength, percent minimum: 50. Elongation, percen
19、t minimum: 50. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17/135D 5 Tensile strength and elongation: 1,300 psi, 160 percent, minimum. Applicable to M17/135-00005 and M17/135-00006. Weight: 16 pounds per 100 feet, max (M17/135-00001 and 0
20、0002). 18.5 pounds per 100 feet, max (M17/135-00003 thru 00006). Watertightness (not applicable to M17/135-00002, M17/135-00004, and M17/135-00006): One end of a five foot length of completed cable shall be placed in a terminal fitting which will allow water pressure to be applied directly to the ex
21、posed cross-sectional area of the end of the cable. Exposure of the sides of the cable to water shall be kept to a minimum, and the fitting shall not exert radial compression against the cable. Unless otherwise approved by the qualifying activity, the sealer used for the packing gland in the termina
22、l fitting shall be a metal alloy having a maximum melting point of 88C. The specimen shall be subjected to a water pressure of 25 lbf /in2for a period of 6 hours. Any evidence of water leakage shall be cause for rejection. Hydrostatic (open end) (not applicable to M17/135-00002, M17/135-00004, and M
23、17/135-00006): A 5-foot specimen of completed cable shall be fitted into a gland similar to USL 44500B-12. The cable shall be capable of withstanding 1,000 lbf/in2 applied to the gland end of the specimen for a period of 2 hours. Any evidence of water leakage shall be cause for rejection. Electrical
24、 Continuity: Applicable. Spark test: 8,000 V rms, +10%, -0%. Voltage withstanding: 10,000 V rms, minimum applied between the inner and outer conductors with the outer conductor grounded; 500 V dc minimum applied between the outer conductor and the extra shield with the extra shield grounded. Insula
25、tion resistance: Not applicable. Corona extinction voltage: 5,000 V rms, minimum. Characteristic impedance: 50 ohms 2. Attenuation: See figure 2. Structural return loss: See figure 3. Capacitance: 32 pF per foot, maximum. Capacitance stability: Not applicable. Capacitance unbalance: Not applicable.
26、Transmission unbalance: Not applicable. Mechanically induced noise voltage: Not applicable. Time delay: Not applicable. Part or Identifying Number (PIN): See table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17/135D 6 Supersession dat
27、a: See table II. NOTE: 1. Maximum power (at 25C seal level) 2. Maximum attenuation 3. Test requirements shall be noted as line indicated on graph. FIGURE 2. Power rating and attenuation Frequency MHz Attenuation dB Watts dB 50 100 400 1000 3000 1.7 2.6 6.4 11.4 23 1400 850 350 190 90 Provided by IHS
28、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17/135D 7 FIGURE 3. Structural return loss. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17/135D 8 FIGURE 3. Structural return loss - Continued. TAB
29、LE II. Cross-reference of PIN. PIN Superseded PIN type or designation Type M17/13500001 1/ AA-3833 Water blocked M17/13500002 1/ TRF-8 Non-water blocked M17/13500003 - Water blocked M17/13500004 - Non-water blocked M17/13500005 2/ AA-7559 Water blocked M17/13500006 2/ AA-7560 Non-water blocked 1/ In
30、active for new design. 2/ Cable previously manufactured using the barrier tape is acceptable for Government use until stock is purged. SWR Reflection coefficient Return loss dB SWR Reflection coefficient Return loss dB 17.3910 8.7242 5.8480 4.4194 3.5698 .8913 .7943 .7079 .6310 .5623 1 2 3 4 5 1.376
31、7 1.3290 1.2880 1.2528 1.2222 .1585 .1413 .1259 .1122 .1000 16 17 18 19 20 3.0095 2.6146 2.3229 2.0999 1.9250 .5012 .4467 .3981 .3548 .3162 6 7 8 9 10 1.1957 1.1726 1.1524 1.1347 1.1192 .0891 .0794 .0708 .0631 .0562 21 22 23 24 25 1.7849 1.6709 1.5769 1.4985 1.4326 .2818 .2512 .2239 .1995 .1778 11 1
32、2 13 14 15 1.1055 1.0935 1.0829 1.0736 1.0653 .0501 .0447 .0398 .0355 .0316 26 27 28 29 30 Frequency MHz MIN. SRL 50 1000 2000 3000 27 21 16 13.8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17/135D 9 Changes from previous issue. The margi
33、ns of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the r
34、equirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references MIL-DTL-17. CONCLUDING MATERIAL Custodians: Preparing activity Army - CR DLA - CC Navy - EC Air Force - 85 (Proj
35、ect 6145-2012-004) DLA - CC Review activities: Army - AR, AT, CR4, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
