1、AMSC N/A FSC 5985 MIL-DTL-24044/1C 15 September 2011 SUPERSEDING MIL-DTL-24044/1B 10 January 2000 DETAIL SPECIFICATION SHEET FLANGES, FIXED, COAXIAL LINE, RIGID This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the pro
2、duct listed herein shall consist of this specification sheet and MIL-DTL-24044. FIGURE 1. 7/8 flange. FIGURE 2. 1-5/8 flange. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24044/1C 2 FIGURE 3. 3-1/8 flange. FIGURE 4. 6-1/8 flange
3、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24044/1C 3 FIGURE 5. Section A-A. FIGURE 6. Inner connector. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24044/1C 4 REQUIREMENTS:
4、Dimensions and configuration: See figures 1 through 6 and table IA, IB, and IC. Materials and reference data: See table II. TABLE IA. Dimensions for figures 1 through 4. Figure 1 Figure 2 Figure 3 Figure 4 Dim Inches mm Degrees and minutes Inches mm Degrees and minutes Inches mm Degrees and minutes
5、Inches mm Degrees and minutes Min .1218 3.09 .1218 3.09 .2465 6.26 .2465 6.26 A Nom .1218 .1218 .2470 .2470 Max .1223 3.11 .1223 3.11 .2470 6.27 .2470 6.27 Min .129 3.28 .129 3.28 .253 6.43 .253 6.43 B Nom .129 1/ .129 3/ .253 6/ .253 8/ Max .133 3.38 .133 3.38 .257 6.53 .257 6.53 Min C Nom .281 2/
6、7.14 .343 4/ 8.71 .406 7/ 10.31 .406 9/ 10.31 Max Min 17953 14955 17957 17958 D Nom 180 150 180 180 Max 1807 1505 1803 1802 Min 2940 1448 2952 2955 E Nom 30 15 30 30 Max 3020 1512 308 305 Min 2.734 69.44 1455 F Nom 120 2.750 5/ 15 Max 2.766 70.26 155 1/ B diameter drill on 1.809 to 1.815 inches (45.
7、95 to 46.10 mm) circle. 2/ C diameter drill: 3 holes equally spaced (120 apart 15, not cumulative) on 1.747 to 1.753 inches (44.37 to 44.53 mm) circle. 3/ B diameter drill on 2.809 to 2.815 inches (71.35 to 71.50 mm) circle. 4/ C diameter drill: 4 holes equally spaced (90 apart 15, not cumulative) o
8、n 2.809 to 2.815 inches (71.35 to 71.50 mm) circle. 5/ Square flange optional. 6/ B diameter drill on 4.372 to 4.378 inches (111.05 to 111.20 mm) circle. 7/ C diameter drill: 6 holes equally spaced (60 apart 15, not cumulative) on 4.370 to 4.380 inches (111.00 to 111.25 mm) circle. 8/ B diameter dri
9、ll on 7.372 to 7.378 inches (187.25 to 187.40 mm) circle. 9/ C diameter drill: 12 holes equally spaced (30 apart 5, not cumulative) on 7.370 to 7.380 inches (187.20 to 187.45 mm) circle. 10/ Metric equivalents tabulated and in parentheses are for general information only. Provided by IHSNot for Resa
10、leNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24044/1C 5 TABLE IB. Dimensions for figure 5. M-24044/1- 1 and 2 7/8 50 ohm M-24044/1- 3 and 4 7/8 75 ohm M-24044/1- 5 and 6 1-5/8 50 ohm M-24044/1- 7 and 8 1-5/8 75 ohm M-24044/1- 9 and 10 3-1/8 50 ohm M-24044/1- 11 and
11、12 3-1/8 75 ohm M-24044/1- 13 and 14 6-1/8 50 ohm Dim Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Min 2.235 56.77 2.235 56.77 3.484 88.50 3.484 88.50 5.1719 131.36 5.1719 131.36 8.109 205.97 A Nom 2.250 57.15 2.250 57.15 3.5 88.90 3.5 88.90 5.1875 131.76 5.1875 131.76 8.125
12、 206.38 Max 2.265 57.53 2.265 57.53 3.516 89.30 3.516 89.30 5.2031 132.16 5.2031 132.16 8.141 206.78 Min 1.350 34.29 1.350 34.29 2.305 58.55 2.305 58.55 3.805 96.65 3.805 96.65 6.795 172.59 B Nom 1.350 34.29 1.350 34.29 2.310 58.67 2.310 58.67 3.810 96.77 3.810 96.77 6.800 172.72 Max 1.355 34.42 1.3
13、55 34.42 2.315 58.80 2.315 58.80 3.815 96.90 3.815 96.90 6.805 172.85 Min 1.025 26.04 1.025 26.04 1.815 46.10 1.815 46.10 3.320 84.33 3.320 84.33 6.215 157.86 C Nom 1.030 26.16 1.030 26.16 1.820 46.23 1.820 46.23 3.325 84.46 3.325 84.46 6.220 157.99 Max 1.030 26.16 1.030 26.16 1.825 46.36 1.825 46.3
14、6 3.330 84.58 3.330 84.58 6.225 158.12 Min .815 20.70 .815 20.70 1.647 41.83 1.647 41.83 3.203 81.36 3.203 81.36 6.075 154.31 D Nom .815 20.70 .815 20.70 1.647 41.83 1.647 41.83 3.203 81.36 3.203 81.36 6.075 154.31 Max .820 20.83 .820 20.83 1.652 41.96 1.652 41.96 3.208 81.48 3.208 81.48 6.080 154.4
15、3 Min .782 19.86 .782 19.86 1.524 38.71 1.524 38.71 3.022 76.76 3.022 76.76 5.973 151.71 E Nom .785 19.94 .785 19.94 1.527 38.79 1.527 38.79 3.027 76.89 3.027 76.89 5.981 151.92 Max .788 20.02 .788 20.02 1.530 38.86 1.530 38.86 3.032 77.01 3.032 77.01 5.989 152.12 Min .878 22.30 .878 22.30 1.628 41.
16、35 1.628 41.35 3.130 79.50 3.130 79.50 6.130 155.70 F Nom .878 22.30 .878 22.30 1.628 41.35 1.628 41.35 3.130 79.50 3.130 79.50 6.133 155.78 Max .881 22.36 .881 22.36 1.631 41.43 1.631 41.43 3.133 79.58 3.133 79.58 6.138 155.91 Min .093 2.36 .093 2.36 .125 3.18 .125 3.18 .187 4.75 .187 4.75 .218 5.5
17、4 G Nom .093 2.36 .093 2.36 .125 3.18 .125 3.18 .187 4.75 1.87 4.75 .218 5.54 Max .098 2.49 .098 2.49 .130 3.30 .130 3.30 .192 4.88 .192 4.88 .223 5.66 Min .048 1.22 .048 1.22 .077 1.96 .077 1.96 .077 1.96 .077 1.96 .110 2.79 H Nom .053 1.35 .053 1.35 .080 2.03 .080 2.03 .080 2.03 .080 2.03 .115 2.9
18、2 Max .053 1.35 .053 1.35 .080 2.03 .080 2.03 .080 2.03 .080 2.03 .120 3.05 Min .005 0.13 .005 0.13 .005 0.13 .005 0.13 .004 0.10 .004 0.10 .008 0.20 J Nom .005 0.13 .005 0.13 .010 0.25 .010 0.25 .010 0.25 .010 0.25 .014 0.35 Max .015 0.38 .015 0.38 .015 0.38 .015 0.38 .016 0.41 .016 0.41 .020 0.51
19、Min .3125 7.94 .3125 7.94 .375 9.53 .375 9.53 .4375 11.11 .4375 11.11 .531 13.49 K Nom .3125 7.94 .3125 7.94 .375 9.53 .375 9.53 .4375 11.11 .4375 11.11 .531 13.49 Max - - - - - - - - - - - - - - Min .140 3.56 .140 3.56 .234 5.94 .234 5.94 .359 9.12 .359 9.12 .359 9.12 L Nom .156 3.96 .156 3.96 .250
20、 6.35 .250 6.35 .375 9.53 .375 9.53 .375 9.53 Max .172 4.37 .172 4.37 .266 6.76 .266 6.76 .391 9.93 .391 9.93 .391 9.93 1/ Metric equivalents tabulated for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24044/1C 6 T
21、ABLE IC. Dimensions for figure 6. M-24044/1- 1 and 2 7/8 50 ohm M-24044/1- 3 and 4 7/8 75 ohm M-24044/1- 5 and 6 1-5/8 50 ohm M-24044/1- 7 and 8 1-5/8 75 ohm M-24044/1- 9 and 10 3-1/8 50 ohm M-24044/1- 11 and 12 3-1/8 75 ohm M-24044/1- 13 and 14 6-1/8 50 ohm Dim Inches mm Inches mm Inches mm Inches
22、mm Inches mm Inches mm Inches mm Min - - - - - - - - - - - - - - A Nom 2.688 68.28 2.688 68.28 3.250 82.55 3.250 82.55 4.250 107.95 4.250 107.95 5.50 139.70 Max 2.688 68.28 2.688 68.28 3.250 82.55 3.250 82.55 4.250 107.95 4.250 107.95 5.50 139.70 Min - - - - - - - - - - - - - - B Nom 1.344 34.14 1.3
23、44 34.14 1.625 41.28 1.625 41.28 2.125 53.98 2.125 53.98 2.750 69.85 Max 1.344 34.14 1.344 34.14 1.625 41.28 1.625 41.28 2.125 53.98 2.125 53.98 2.750 69.85 Min - - - - - - - - - - - - - - C Nom .433 11.00 .433 11.00 .573 14.55 .573 14.55 .893 22.68 .893 22.68 1.221 31.01 Max .433 11.00 .433 11.00 .
24、573 14.55 .573 14.55 .893 22.68 .893 22.68 1.221 31.01 Min .810 20.57 .810 20.57 1.640 41.66 1.640 41.66 3.195 81.15 3.195 81.15 6.067 154.10 D Nom .812 20.63 .812 20.63 1.645 41.78 1.645 41.78 3.198 81.23 3.198 81.23 6.072 154.23 Max .812 20.63 .812 20.63 1.645 41.78 1.645 41.78 3.198 81.23 3.198 8
25、1.23 6.072 154.23 Min .339 8.61 .224 5.69 .6615 16.80 .436 11.07 1.312 33.33 .8665 22.01 2.596 65.94 E Nom .341 8.66 .226 5.74 .6640 16.86 .438 11.13 1.315 33.40 .8690 22.07 2.600 66.04 Max .343 8.71 .228 5.79 .6665 16.93 .440 11.18 1.318 33.48 .8715 22.14 2.604 66.14 Min .183 4.65 .183 4.65 .244 6.
26、20 .244 6.20 .367 9.32 .367 9.32 .429 10.90 F Nom .185 4.70 .185 4.70 .249 6.32 .249 6.33 .372 9.45 .372 9.45 .434 11.02 Max .185 4.70 .185 4.70 .249 6.32 .249 6.33 .372 9.45 .372 9.45 .434 11.02 1/ Figure 6 for assurance of interchangeability only of inner connector. 2/ All diameters to be concentr
27、ic within .005 inch (0.13 mm) except stock size (O.D.). 3/ Metric equivalents tabulated for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24044/1C 8 TABLE II. Requirements. PIN Type Size (inches) Nominal impedance
28、(ohms) Material Figure no. Mates with self and Hi. pot. test (kv) “O” ring data Bolt data Inner connector PIN Type Figure M-24044/1-01 M-24044/1-02 M-24044/1-03 M-24044/1-04 CG-3030/U CG-3006/U CG-3007/U CG-3008/U 7/8 7/8 7/8 7/8 50 50 75 75 Copper-base alloy Aluminum-base alloy Copper-base alloy Al
29、uminum-base alloy 1 and 5 1 and 5 1 and 5 1 and 5 M-24044/2-01 M-24044/2-02 M-24044/2-03 M-24044/2-04 5 5 5 5 O.D. 1.324 inch (33.63 mm) I.D.1.046 inch (26.57 mm) 3 each 1/2-20 x 1 long Inch (min) M-24044/1-01C M-24044/1-01C M-24044/1-03C M-24044/1-03C UG-1164/U UG-1164/U CG-3036/U CG-3036/U 6 6 6 6
30、 M-24044/1-05 M-24044/1-06 M-24044/1-07 M-24044/1-08 CG-3032/U CG-3012/U CG-3013/U CG-3014/U 1-5/8 1-5/8 1-5/8 1-5/8 50 50 75 75 Copper-base alloy Aluminum-base alloy Copper-base alloy Aluminum-base alloy 2 and 5 2 and 5 2 and 5 2 and 5 M-24044/2-05 M-24044/2-06 M-24044/2-07 M-24044/2-08 10 10 10 10
31、 O.D. 2.270 inch (57.66 mm) I.D.1.850 inch (46.99 mm) 4 each 5/16-18 x 1-1/2 long Inch (min) M-24044/1-05C M-24044/1/05C M-24044/1-07C M-24044/1-07C UG-1161/U UG-1161/U CG-3037/U CG-3037/U 6 6 6 6 M-24044/1-09 M-24044/1-10 M-24044/1-11 M-24044/1-12 CG-3018/U CG-3020/U CG-3019/U CG-3021/U 3-1/8 3-1/8
32、 3-1/8 3-1/8 50 50 75 75 Copper-base alloy Aluminum-base alloy Copper-base alloy Aluminum-base alloy 3 and 5 3 and 5 3 and 5 3 and 5 M-24044/2-09 M-24044/2-10 M-24044/2-11 M-24044/2-12 20 20 20 20 O.D. 3.770 inch (95.76 mm) I.D.3.350 inch (85.09 mm) 6 each 3/8-16 x 1-1/2 long Inch (min) M-24044/1-09
33、C M-24044/1-09C M-24044/1-11C M-24044/1-11C CG-3034/U CG-3034/U CG-3038/U CG-3038/U 6 6 6 6 M-24044/1-13 M-24044/1-14 CG-3026/U CG-3027/U 6-1/8 6-1/8 50 50 Copper-base alloy Aluminum-base alloy 4 and 5 4 and 5 M-24044/2-13 M-24044/2-14 20 20 O.D. 6.775 inch (172.09 mm) I.D.6.225 inch (158.12 mm) 12
34、each 3/8-16 x 1-3/4 long Inch (min) M-24044/1-13C M-24044/1-13C CG-3035/U CG-3035/U 6 6 1/ Flange size is defined by the nominal outside diameter of the line with which it is used. 2/ “C” on PIN denotes inner connector used with flange. 3/ Metric equivalents tabulated in parentheses are for general
35、information only. MIL-DTL-24044/1C7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24044/1C 8 Referenced documents: This document references only the following: MIL-DTL-24044. Marginal notations are not used in this revision to identify chang
36、es with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5985-2011-031) DLA - CC Review activities: Navy - AS, MC, OS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
