1、AMSC N/A FSC 5935 MIL-DTL-24308/26L w/AMENDMENT 4 11 December 2013 SUPERSEDING w/AMENDMENT 3 9 April 2013 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, POLARIZED SHELL, RACK AND PANEL, SCREW-LOCK ASSEMBLY, FEMALE This specification is approved for use by all Departments an
2、d Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24308. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. When a connector using the alternate method o
3、f securing the shell (tab type) is front mounted, one flat washer shall be used as a spacer between the mounting surface and the connector. 4. Female screw-lock assembly supplied as an individual order, not by the pair. FIGURE 1. Dimensions and configuration. Inches mm .015 0.38 .030 0.76 .032 0.81
4、107 2.72 .112 2.84 .120 3.05 .155 3.94 .188 4.78 .216 5.49 .219 5.56 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24308/26L w/AMENDMENT 4 2 REQUIREMENTS: Dimensions and configuration: See figure 1. Material: Cold rolled steel o
5、r corrosion resistant steel in accordance with ASTM A582/A582M. Washer and lock washer: Cold rolled steel or corrosion resistant steel in accordance with ASTM A582/A582M or ASTM A666. Finish: Cold rolled steel - Yellow chromate over cadmium in accordance with SAE AMS-QQ-P-416, or yellow chromate ove
6、r zinc in accordance with ASTM B633 or zinc nickel alloy in accordance with ASTM B841 over a suitable underplate or Nickel fluorocarbon polymer over a suitable underplate or pure electrodeposited aluminum in accordance with MIL-DTL-83488. Corrosion resistant steel - Shall be passivated in accordance
7、 with SAE AMS2700, type 6. Jackpost installation torque: 5 inch pounds min. 6 inch-pounds max. Jackpost mating torque: 4 inch-pounds max. Qualification requirements: See MIL-DTL-24308/25. Part or Identifying Number (PIN) example: M24308/26 - 1 F Dash number, see table I Finish A = Pure electrodeposi
8、ted aluminum F = Cadmium K = Zinc nickel P = Passivated stainless steel T = Nickel fluorocarbon polymer Z = Zinc TABLE I. Dash number. Dash no. A .015 -1 -2 .312 .625 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24308/26L w/AMENDMENT 4 3 A
9、mendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are caut
10、ioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents. In addition to MIL-DTL-24308, this document references the following: MIL-DTL-24308/25 MIL-DTL-83488 ASTM A582/A582M ASTM A666 ASTM B633 ASTM B841 SAE AMS-QQ-
11、P-416 SAE AMS2700 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2014-010) NASA - NA DLA - CC Review activities: Army - AT, AV, CR4, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this docume
12、nt as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
